ENGINE ASSEMBLY > INSTALLATION |
| 1. REMOVE ENGINE STAND |
Using a chain block and engine sling device, secure the engine assembly.
Remove the engine stand from the engine.
| 2. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
Clean the bolts and their installation holes.
![]() |
Install the front drive plate spacer.
![]() |
Install the drive plate and rear drive plate spacer onto the crankshaft.
| *1 | Drive Plate |
| *2 | Rear Drive Plate Spacer |
![]() | Transaxle Side |
![]() |
Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 8 bolts.
| *1 | Adhesive |
![]() |
Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.
| 3. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY |
![]() |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.
| *1 | Torque Converter Centerpiece |
| *2 | Crankshaft |
![]() |
While keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the 9 bolts shown in the illustration.
| Bolt | Bolt Length | Torque |
| A | 55 mm (2.17 in.) | 64 N*m (653 kgf*cm, 47 ft.*lbf) |
| B | 50 mm (1.97 in.) | 46 N*m (469 kgf*cm, 34 ft.*lbf) |
| C | 32 mm (1.26 in.) | 44 N*m (449 kgf*cm, 32 ft.*lbf) |
| 33 mm (1.30 in.) | 43 N*m (438 kgf*cm, 32 ft.*lbf) |
| 4. INSTALL ENGINE MOUNTING BRACKET RH |
Install the engine mounting bracket RH with the 3 bolts.
| 5. INSTALL DRIVE SHAFT BEARING BRACKET |
Install the drive shaft bearing bracket with the 3 bolts.
| 6. TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR |
Temporarily install the front engine mounting insulator with the 3 nuts.
| 7. TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH |
Temporarily install the engine mounting insulator LH with the 3 nuts.
| 8. TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH |
Temporarily install the engine mounting insulator RH with the 3 nuts.
| 9. INSTALL FRONT FRAME ASSEMBLY |
Install the engine mounting insulator LH with the nut.
Install the engine mounting insulator RH with the nut.
Install the front engine mounting insulator with the bolt.
Fully tighten the 9 temporarily installed nuts of the engine mounting insulators to the specified torque.

| *a | Front Engine Mounting Insulator | *b | Engine Mounting Insulator RH |
| *c | Engine Mounting Insulator LH | - | - |
Install the 4 hole plugs.

| *a | Engine Mounting Insulator RH | *b | Engine Mounting Insulator LH |
| 10. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH |
Install a new front drive shaft hole snap ring LH.
| 11. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
Coat the spline of the front drive inboard joint assembly with ATF.
Coat the lip of the transaxle case oil seal with MP grease.
![]() |
Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.
![]() |
Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.
| *a | Matchmark |
| 12. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
Coat the spline of the front drive inboard joint assembly with ATF.
Coat the lip of the front transaxle case oil seal with MP grease.
Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.
Install the front drive shaft assembly RH.
![]() |
Install the bearing bracket hole snap ring and a new bolt.
![]() |
Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.
| *a | Matchmark |
| 13. INSTALL GENERATOR ASSEMBLY |
![]() |
Disconnect the generator connector.
Remove the terminal cap.
Remove the nut and disconnect the generator wire.
Remove the bolt and wire harness clamp bracket.
![]() |
Remove the 2 bolts and generator.
| 14. INSTALL COMPRESSOR AND PULLEY |
![]() |
Remove the 2 bolts and 2 nuts.
![]() |
Using an E8 "TORX" socket, remove the 2 stud bolts and compressor assembly with pulley.
| 15. INSTALL V-RIBBED BELT |
![]() |
Set the V-ribbed belt onto each part as shown in the illustration except the water pump pulley.
| *1 | Crankshaft |
| *2 | Tensioner |
| *3 | Generator |
| *4 | Water Pump |
| *5 | Cooler Compressor |
Loosen the V-ribbed belt by turning the belt tensioner clockwise.
Set the V-ribbed belt onto the water pump pulley.
| 16. INSTALL ENGINE WIRE |
Install the engine wire to the engine with transaxle.
| 17. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
Remove the engine hangers .
Set the engine assembly with transaxle on an engine lifter.
Install the engine assembly to the vehicle.
![]() |
Install the frame side rail plate RH and LH with the 4 bolts and 2 nuts.
Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.
| 18. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
![]() |
Apply a few drops of adhesive to the first 2 or 3 threads of the 6 drive plate and torque converter setting bolts.
| *1 | Adhesive |
![]() |
Turn the crankshaft to gain access to the installation locations of the 6 torque converter setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.
| 19. INSTALL FLYWHEEL HOUSING UNDER COVER |
Install the flywheel housing under cover.
| 20. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks and install the steering intermediate shaft to the steering link assembly.
| *a | Matchmark |
Install the bolt.
| 21. INSTALL FRONT AXLE ASSEMBLY LH |
![]() |
Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
| *a | Matchmark |
| 22. INSTALL FRONT AXLE ASSEMBLY RH |
| 23. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.
| 24. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH |
| 25. INSTALL TIE ROD ASSEMBLY LH |
Connect the tie rod assembly LH to the steering knuckle with the nut.
Install a new cotter pin.
| 26. INSTALL TIE ROD ASSEMBLY RH |
| 27. INSTALL FRONT SPEED SENSOR LH |
Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.
Install the front speed sensor to the steering knuckle with the bolt.
| 28. INSTALL FRONT SPEED SENSOR RH |
| 29. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
Install the front stabilizer link assembly to the front shock absorber assembly with the nut.
| 30. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 31. INSTALL FRONT AXLE SHAFT NUT LH |
Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using a non-residue solvent.
Using a socket wrench (30 mm), install the front axle hub shaft nut.
| 32. INSTALL FRONT AXLE SHAFT NUT RH |
| 33. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum | 40.5 mm (1.60 in.) |
Fully insert a new gasket to the exhaust manifold converter sub-assembly.
![]() |
Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.
| *1 | Exhaust Manifold Converter Sub-assembly |
| *2 | Gasket |
| *3 | Wooden Block |
Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.
Connect the front exhaust pipe assembly to the exhaust pipe support.
| 34. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Push in the fuel tube connector to the fuel pipe until the connector makes a "click" sound.
![]() |
Install the No. 1 fuel pipe clamp.
| 35. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.
Install the O-ring onto the No. 1 cooler refrigerant discharge hose.
Install the No. 1 cooler refrigerant discharge hose onto the compressor assembly with pulley with the bolt.
Connect the 2 connectors.
Install the bolt.
| 36. INSTALL NO. 1 COOLER REFRIGERANT SUCTION HOSE |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.
Install the O-ring onto the No. 1 cooler refrigerant suction hose.
Install the No. 1 cooler refrigerant suction hose onto the compressor assembly with pulley with the bolt.
Connect the 2 connectors.
Install the bolt.
| 37. CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD) |
Connect the union to connector tube hose.
| 38. CONNECT UNION TO CHECK VALVE HOSE (for RHD) |
Connect the union to check valve hose.
| 39. INSTALL ENGINE MOVING CONTROL ROD |
Temporarily install the engine moving control rod to the engine moving control rod bracket with the bolt.
| 40. INSTALL ENGINE MOVING CONTROL ROD BRACKET |
![]() |
When the engine moving control rod has been replaced.
Temporarily install the engine moving control rod bracket with the 4 bolts.
Fully tighten the engine moving control rod bracket with the bolts except bolt A.
![]() |
Fully tighten the bolt A.
![]() |
When the engine moving control rod has been reused.
Temporarily install the engine moving control rod bracket with the 4 bolts.
Fully tighten the engine moving control rod bracket with the 4 bolts.
| 41. INSTALL EARTH WIRE |
Install the earth wire with the bolt.
| 42. INSTALL NO. 2 ENGINE MOUNTING STAY RH |
Install the No. 2 engine mounting stay RH with the 2 bolts.
| 43. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Connect the control cable to the bracket with a new clip.
![]() |
Install the control cable to the control shaft lever with the nut.
| 44. INSTALL NO. 1 AIR CLEANER BRACKET |
Install the No. 1 air cleaner bracket to the battery carrier with the bolt.
Connect the 2 wire clamps.
| 45. CONNECT ENGINE WIRE |
![]() |
Connect the 2 wire clamps.
Connect the connector to the ECM with the lock lever.
Connect the engine wire to the engine room relay block.
Connect the 4 connectors.
![]() |
Connect the engine wire to the engine room relay block.
Connect the wire clamp and install the 2 nuts.
Install the No. 1 relay block cover.
| 46. INSTALL STARTER ASSEMBLY (for 1.6 kW Type) |
Install the starter assembly with the 2 bolts.
Connect the starter connector.
Install the terminal nut and cover the nut with the cap.
| 47. INSTALL STARTER ASSEMBLY (for 1.7 kW Type) |
Install the starter assembly with the 2 bolts.
Connect the starter connector.
Install the terminal nut and cover the nut with the cap.
| 48. CONNECT INLET HEATER WATER HOSE |
Connect the inlet heater water hose.
| 49. CONNECT OUTLET HEATER WATER HOSE |
Connect the outlet heater water hoses.
| 50. CONNECT INLET NO. 1 OIL COOLER HOSE |
Connect the inlet No. 1 oil cooler hose to the automatic transaxle assembly.
| 51. CONNECT OUTLET NO. 1 OIL COOLER HOSE |
Connect the outlet No. 1 oil cooler hose to the automatic transaxle assembly.
| 52. CONNECT NO. 1 RADIATOR HOSE |
Connect the air fuel ratio sensor wire to the No. 1 radiator hose with the hose clamp.
| 53. CONNECT NO. 2 RADIATOR HOSE |
Connect the No. 2 radiator hose.
| 54. INSTALL BATTERY |
Install the battery and battery tray.
Install the battery clamp with the bolt and nut.
Connect the positive (+) battery terminal
| 55. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.
| *a | Wire harness clamp |
| *b | Hole |
| *c | Projection |
Tighten the 2 bolts.
Connect the wire harness clamp.
| 56. INSTALL AIR CLEANER FILTER ELEMENT |
| 57. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Install the air cleaner cap sub-assembly with the 2 clamps.
Install the air cleaner hose with the hose clamp.
Connect the ventilation hose to the cylinder head cover.
Install the fuel vapor feed hose to the air cleaner hose.
Connect the mass air flow meter connector and 2 wire harness clamps to the air cleaner cap sub-assembly.
Connect the vacuum switching valve assembly to the air cleaner hose.
| 58. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner with the 2 bolts.
| 59. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 60. ADD ENGINE OIL |
| 61. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
![]() |
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| *a | Code Mark |
| Code Mark "M" | 6.9 liters (7.3 US qts, 6.1 lmp. qts) |
| Code Mark "G" | 7.0 liters (7.4 US qts, 6.2 lmp. qts) |
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 62. ADD AUTOMATIC TRANSAXLE FLUID |
| 63. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100 g (3.5 oz.) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| 64. WARM UP ENGINE |
| 65. INSPECT FOR FUEL LEAK |
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
| 66. INSPECT FOR OIL LEAK |
| 67. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 68. INSPECT FOR EXHAUST GAS LEAK |
| 69. INSPECT REFRIGERANT LEAK |
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
| *1 | Halogen Leak Detector |
| *a | Inspect for Leak |
![]() |
Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.
| 70. INSPECT IGNITION TIMING |
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Start the engine and idle it.
Turn the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine / Data List / IGN Advance.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / ON.
Monitor IGN Advance of the Data List.
Enter the following menus: Connect the TC and TE1 / OFF.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
Remove the No. 1 engine cover sub-assembly.
![]() |
Pull out the wire harness as shown in the illustration.
Connect the clip of a timing light to the wire harness.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *1 | DLC3 |
Using a timing light, check the ignition timing.
Remove SST from the DLC3.
Check the ignition timing.
Check that the ignition timing advances immediately when the engine speed is increased.
Disconnect the timing light from the engine.
Install the No. 1 engine cover sub-assembly.
| 71. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Turn the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
| *1 | DLC3 |
Race the engine at 2500 rpm for approximately 90 seconds.
Check the idle speed.
Disconnect the tachometer probe from the DLC3.
| 72. INSPECT CO/HC |
Start the engine.
Keep the engine speed at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.
Immediately check CO/HC concentration at idle and 2500 rpm.
Check the A/F sensor and heated oxygen sensor operation.
See the table below for possible causes, and then inspect and correct the applicable causes if necessary.
| CO | HC | Symptom | Causes |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 73. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
Fit the 3 retainers and install the No.1 engine cover sub-assembly.
| 74. INSTALL COOL AIR INTAKE DUCT SEAL |
Install the cool air intake duct seal with the 9 clips.
| 75. INSPECT AND ADJUST SHIFT LEVER POSITION |
| 76. INSTALL FRONT FENDER APRON SEAL LH |
| 77. INSTALL FRONT FENDER APRON SEAL RH |
| 78. INSTALL ENGINE UNDER COVER LH |
| 79. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
| 80. INSTALL ENGINE UNDER COVER RH |
| 81. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |
| 82. INSTALL FRONT WHEEL |
| 83. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 84. CHECK ABS SPEED SENSOR SIGNAL |