Home › Engine / Hybrid System ยท 1AZ-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (Click here).



2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
  1. Turn the A/C switch on.

  1. Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.

  1. Turn the ignition switch off.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.



3. DISCHARGE FUEL SYSTEM PRESSURE



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the oil into a container.

  1. Clean and install the oil pan drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Using a 10 mm hexagon socket wrench, remove the drain plug and gasket, and drain the ATF.

  1. Using a 10 mm hexagon socket wrench, install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



7. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

  1. Loosen the cylinder block drain cock plug.



  1. Remove the radiator cap sub-assembly.


    A264832E01


    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Radiator Drain Cock Plug
    *3
    Cylinder Block Drain Cock Plug
    -

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.



8. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


9. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY


    C239198
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C239185
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



10. REMOVE COOL AIR INTAKE DUCT SEAL


    B282103
  1. Remove the 9 clips and cool air intake duct seal.



11. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    A134904
  1. Remove the 2 nuts and No. 1 engine cover sub-assembly.



12. REMOVE INLET AIR CLEANER ASSEMBLY


    A264362
  1. Remove the 2 bolts and inlet air cleaner assembly.



13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A264433
  1. Disconnect the vacuum switching valve connector.

  1. Disconnect the 2 vacuum switching valve vacuum hoses.

  1. Disconnect the purge line hose from the 2 clamps.

  1. Disconnect the mass air flow meter connector.

  1. Disconnect the wire harness clamp.

  1. Loosen the 2 bolts and separate the air cleaner cap sub-assembly.



    A264435
  1. Disconnect the ventilation hose from the cylinder head cover sub-assembly.



    A264436E01
  1. Lock the air cleaner hose clamp as shown in the illustration, and disconnect the air cleaner cap sub-assembly from the throttle with motor body assembly.
    Text in Illustration 
    *1
    Air Cleaner Hose Clamp

  1. Remove the air cleaner filter element from the air cleaner case sub-assembly.



14. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A264522
  1. Disconnect the wire harness clamp.

  1. Remove the 3 bolts and air cleaner case sub-assembly.



15. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A134912
  1. Remove the 2 bolts and No. 2 engine mounting stay RH.



16. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY


    A264363
  1. Remove the 3 bolts and engine moving control rod sub-assembly.



17. REMOVE NO. 2 ENGINE MOUNTING BRACKET RH


    A264364
  1. Remove the 3 bolts and No. 2 engine mounting bracket RH.



18. DISCONNECT UNION TO VACUUM TUBE HOSE


    A264238
  1. Disconnect the union to vacuum tube hose from the intake manifold.



19. DISCONNECT NO. 1 RADIATOR HOSE


    A264525
  1. Disconnect the wire harness clamp and No. 1 radiator hose.



20. DISCONNECT NO. 2 RADIATOR HOSE


    A127545E01
  1. Disconnect the No. 2 radiator hose.



21. DISCONNECT INLET NO. 1 OIL COOLER HOSE


    A264369
  1. Disconnect the inlet No. 1 oil cooler hose from the automatic transaxle assembly.



22. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE


    A264370
  1. Disconnect the hose clamp and outlet No. 1 oil cooler hose from the automatic transaxle assembly.



23. DISCONNECT INLET HEATER WATER HOSE


    A264365
  1. Disconnect the breather hose.



    A264366
  1. Disconnect the inlet heater water hose.



24. DISCONNECT OUTLET HEATER WATER HOSE


    A264368
  1. Disconnect the outlet heater water hose.



25. REMOVE STARTER ASSEMBLY


    A134876
  1. Disconnect the connector.

  1. Open the terminal cap, remove the nut and disconnect the starter wire.



    A134877
  1. Remove the 2 bolts and starter assembly.



26. DISCONNECT ENGINE WIRE
  1. Remove the No. 1 relay block cover.



    A264371
  1. Pull up the lever and disconnect the ECM connector and 2 wire harness clamps.



    A264372
  1. Disconnect the 4 connectors and remove the nut.

  1. Using a screwdriver, disengage the claw and separate the engine wire.



    A264373
  1. Remove the bolt and disconnect the wire harness clamp.



    A264374
  1. Disconnect the wire harness clamp.



27. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C222560
  1. Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.



    C199358
  1. Remove the clip and disconnect the transmission control cable assembly from the control cable bracket.



    C200869
  1. Disconnect the control cable from the control cable support.



28. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


    E234907
  1. Disconnect the 2 connectors.

  1. Disengage the 2 clamps.



    E234908
  1. Remove the bolt and bracket.



    E234909
  1. Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the compressor assembly with pulley.

  1. Remove the O-ring from the No. 1 cooler refrigerant discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



29. DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE


    E234910
  1. Remove the bolt and disconnect the No. 1 cooler refrigerant suction hose from the compressor assembly with pulley.

  1. Remove the O-ring from the No. 1 cooler refrigerant suction hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



30. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A261648
  1. Remove the No. 1 fuel pipe clamp.



    A261677E01
  1. Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.
    Text in Illustration 
    *1
    Fuel Pipe
    *2
    Fuel Tube Connector
    *3
    Nylon Tube
    *4
    O-ring
    *5
    Retainer
    V100135
    Pinch
    V100136
    Pull

    NOTICE:
    1. Check for foreign matter on the fuel tube around the fuel tube connector. Clean it if necessary. Foreign matter can affect the ability of the O-ring to seal the fuel tube connector and fuel pipe.
    2. Do not use any tools to separate the fuel tube connector and fuel pipe.
    3. Do not forcibly bend, kink or twist the nylon tube.
    4. Keep the fuel tube connector and fuel pipe free from foreign matter.
    5. If the fuel tube connector and fuel pipe are stuck, push and pull to release them.
    6. Cover the fuel tube connector and fuel pipe with plastic bags to prevent damage and contamination.



    A261678
  1. Remove the fuel tube sub-assembly from the fuel hose clamp.



31. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A266362
  1. Disconnect the oxygen sensor connector.



    A254747
  1. Remove the 2 bolts, 2 nuts, 2 compression springs and front exhaust pipe assembly.

  1. Remove the 2 gaskets from the front exhaust pipe assembly and exhaust manifold converter sub-assembly.



32. REMOVE FRONT DRIVE SHAFT ASSEMBLY
(Click here)


33. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


34. SECURE STEERING WHEEL


    C238510
  1. Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.



35. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY


    C238511E02
  1. Put matchmarks on the steering intermediate shaft assembly and steering link assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the bolt.

  1. Separate the steering intermediate shaft assembly from the steering link assembly.



36. REMOVE FLYWHEEL HOUSING UNDER COVER


    D025407
  1. Remove the flywheel housing under cover.



37. REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT


    C092290
  1. Turn the crankshaft to gain access to the removal locations of the 6 drive plate and torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.



38. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE


    A264389
  1. Set an engine lifter.
    Text in Illustration 
    V100145
    Attachment Installation Position

    NOTICE:
    1. Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.
    2. Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.
    3. To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.
    4. Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.
    5. Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed or removed from an engine stand.



    A264390
  1. Remove the 4 bolts, 2 nuts, and frame side rail plate RH and LH.

  1. Remove the 4 bolts, 2 nuts, and front suspension member brace rear RH and LH.

  1. Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

    NOTICE:
    1. Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
    2. While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.

  1. Remove the engine wire from the engine assembly with transaxle.



39. INSTALL ENGINE HANGERS


    A162166E08
  1. Install the 2 engine hangers with the 2 bolts.
    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

    Part Name
    Part No.
    No. 1 engine hanger
    12281-28010
    No. 2 engine hanger
    12282-28010
    Bolt
    91552-B1020



40. REMOVE V-RIBBED BELT


    A264360E01
  1. Using SST, slowly turn the V-ribbed belt tensioner assembly clockwise.

    NOTICE:
    1. Make sure that SST and other tools are set to the V-ribbed belt tensioner assembly securely.
    2. When compressing the V-ribbed belt tensioner assembly, slowly turn the V-ribbed belt tensioner assembly.

    SST
    09216-42010  

  1. Remove the V-ribbed belt from each pulley and slowly return the V-ribbed belt tensioner assembly.



41. REMOVE COMPRESSOR ASSEMBLY WITH PULLEY


    E234911
  1. Remove the 4 bolts and compressor assembly with pulley.



42. REMOVE GENERATOR ASSEMBLY


    A192602
  1. Disconnect the connector and wire harness clamp.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the bolt and wire harness clamp bracket.



    A192601
  1. Remove the 2 bolts and generator assembly.



43. REMOVE FRONT FRAME ASSEMBLY


    A255456
  1. Remove the nut and separate the engine mounting insulator LH .



    A289267
  1. Remove the bolt and separate the front engine mounting insulator.



    A282839
  1. Remove the nut and separate the engine mounting insulator RH.

  1. Remove the front frame assembly.

  1. Using a height adjustable attachment and plate lift attachment, place the engine assembly with transaxle on a flat level surface.

    NOTICE:
    1. Using a height adjustable attachment and plate lift attachment, place the engine assembly with transaxle horizontally.
    2. To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.
    3. Using an engine sling device and engine lift, secure the engine assembly with transaxle before service.



44. REMOVE FRONT ENGINE MOUNTING INSULATOR


    A289268
  1. Remove the 3 nuts and front engine mounting insulator.

    HINT:
    Perform this procedure only when replacement of the front engine mounting insulator is necessary.



45. REMOVE ENGINE MOUNTING INSULATOR LH


    A264375
  1. Remove the 2 hole plugs from the front frame assembly.



    A264555
  1. Remove the 3 nuts and engine mounting insulator LH.

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator LH is necessary.



46. REMOVE ENGINE MOUNTING INSULATOR RH


    A264376
  1. Remove the 2 hole plugs from the front frame assembly.



    A282840
  1. Remove the 3 nuts and engine mounting insulator RH.

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator RH is necessary.



47. REMOVE DRIVE SHAFT BEARING BRACKET


    A134945
  1. Remove the 3 bolts and drive shaft bearing bracket.



48. REMOVE ENGINE MOUNTING BRACKET RH


    A282838
  1. Remove the 3 bolts and engine mounting bracket RH.



49. DISCONNECT ENGINE WIRE


    C248852
  1. Remove the bolt and disconnect the 4 connectors, 6 clamps and engine wire from the automatic transaxle assembly.



50. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY
  1. Using a transmission jack attachment, set the automatic transaxle assembly on a transmission jack.

    NOTICE:
    1. Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.
    2. To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the automatic transaxle assembly.
    3. Hold the engine assembly with a suitable adapter, such as a rope, during the operation.



    C248853
  1. Remove the 9 bolts and automatic transaxle assembly.

    NOTICE:
    To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine.



51. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A264395E01
  1. Using SST, hold the crankshaft pulley.
    Text in Illustration 
    *a
    Hold

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A264396
  1. Remove the 8 bolts, the front drive plate spacer, the drive plate and ring gear sub-assembly, and the rear drive plate spacer.



52. INSTALL ENGINE STAND
  1. Install the engine onto an engine stand with the bolts.