Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    U0073    Control Module Communication Bus OFF

DTC    U0100    Lost Communication with ECM / PCM

DTC    U0123    Lost Communication with Yaw Rate Sensor Module

DTC    U0126    Lost Communication with Steering Angle Sensor Module

for Preparation Click here


DESCRIPTION

The skid control ECU receives signals from the ECM, steering angle sensor and yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

DTC No.
DTC Detection Condition
Trouble Area
U0073
The +BS terminal voltage is between 9.6 and 16.5 V and bus off is judged for 0.1 seconds or more.
CAN communication system
U0100
The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the ECM for 2.5 seconds or more.
  1. CAN communication system
  2. Skid control ECU (Brake actuator assembly)
  3. ECM
U0123
The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the yaw rate and acceleration sensor cannot be received for 1.1 seconds or more.
  1. CAN communication system
  2. Skid control ECU (Brake actuator assembly)
  3. Yaw rate and acceleration sensor (Airbag sensor assembly)
U0126
The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the steering angle sensor cannot be received for 1.1 seconds or more.
  1. CAN communication system
  2. Skid control ECU (Brake actuator assembly)
  3. Steering angle sensor

WIRING DIAGRAM


for LHD

C269200E02


for RHD

C243537E03


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    EFI Communication Open
    EFI communication open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    Yaw Rate Open
    Yaw rate sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    Steering Open
    Steering angle sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -

    Result:

    Result
    Proceed to
    There is a constant interruption. (Error is displayed without interruption)
    A
    There are no momentary interruptions.
    B
    There are momentary interruptions. (Error is displayed intermittently)
    C

    HINT:
    Perform the above inspection before disconnecting any sensors or connectors.



B
Go to step 3

C
Go to step 4
A


2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
  1. Turn the ignition switch off.

  1. Check if each sensor or ECM connector is securely connected.

    OK:
    Each connector is securely connected.



NG
CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY
OK


3.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Record the output DTCs (for VSC system and/or CAN communication system) (Click here for VSC system, or Click here for CAN communication system).

    HINT:
    If CAN communication system DTCs and related sensor DTCs are output simultaneously, troubleshoot the DTCs (for VSC system) after the CAN communication system returns to normal.


    Result:

    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B
    CAN communication system DTC is output.
    C



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

C
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Turn the ignition switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruptions between the skid control ECU and each sensor or ECM (Click here).


NEXT


5.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.

  1. Check that no CAN communication system DTC is output (Click here).

  1. If VSC system DTCs are output, record them (Click here).

    Result:

    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B
    CAN communication system DTC is output.
    C

    HINT:
    The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for VSC system).



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

C
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A

END