CAN COMMUNICATION SYSTEM > DIAGNOSIS SYSTEM |
| ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM |
V Bus
ECM
Brake actuator assembly
Main body ECU (Multiplex network body ECU)
Air conditioning amplifier assembly
Power steering ECU with motor assembly
Smart key ECU assembly (Certification ECU)*1
Airbag sensor assembly
Steering sensor
Clearance warning ECU assembly*2
AFS ECU*3
Combination meter assembly
Navigation ECU sub-assembly*4
Radio and display receiver assembly*5
Sub Bus 1*6
Main body ECU (Multiplex network body ECU)
Multiplex tilt and telescopic ECU
| CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION |
The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.
| ECU/Sensor Name | intelligent Tester Display | Applicability |
| ECM | ECM (Engine) | Installed on all vehicles |
| AFS ECU | Headlight swivel (AFS) | Vehicles with AFS |
| Combination meter assembly | Combination Meter | Installed on all vehicles |
| Main body ECU (Multiplex network body ECU) | Main Body | Installed on all vehicles |
| Power steering ECU with motor assembly | Power Steering (EPS) | Installed on all vehicles |
| Brake actuator assembly | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles |
| Steering sensor | Spiral cable (Steering Angle Sensor) | Installed on all vehicles |
| Airbag sensor assembly | Airbag | Installed on all vehicles |
| Smart key ECU assembly (Certification ECU) | Certification (Smart) | Vehicles with smart entry and start system |
| Air conditioning amplifier assembly | Air Conditioning Amplifier | Installed on all vehicles |
| Navigation ECU sub-assembly | Display and Navigation (AVN1) | Vehicles with navigation system |
| Radio and display receiver assembly | Display and Navigation (AVN1) | Vehicles with audio and visual system |
| Clearance warning ECU assembly | Clearance warning (Clearance Sonar2) | Vehicles with Toyota parking assist-sensor system |
| Multiplex tilt and telescopic ECU | Multiplex Tilt and Telescopic | Vehicles with power tilt and power telescopic steering column system |
| BUS CHECK (COMMUNICATION BUS CHECK) |
![]() |
Select "Bus Check" from the "System Select" screen on the intelligent tester.
![]() |
Select "Communication Bus Check" from the "Bus Check" screen.
![]() |
The screen displays the ECUs and sensors that are properly connected to the CAN communication system.
![]() |
"There is no system connected to the communication bus" is displayed if there are no ECUs or sensors connected to the CAN bus.
![]() |
The default item displayed in the pull down menu is "ALL". When checking the ECUs (sensors) connected to each bus, open the pull down menu and select the bus to be checked from the pull down menu. The pull down menu displays "ALL", "V Bus", and the names of the remaining buses.
| Pull Down Menu | Display Content |
| ALL | All ECUs (sensors) connected to the CAN bus |
| V Bus | ECUs (sensors) connected to the V Bus |
| Bus Name | ECUs (sensors) connected to the selected bus |
| *a | Pull down menu |
| *b | List |
| *c | Example of displayed item |
| *d | Bus (V bus or sub bus) selected using pull down menu. |
| Bus Type | Background Color | Connection Status |
| V Bus | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the communication bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the communication bus check.*1 | |
| Sub bus (gateway function equipped ECU that does not have history of connected ECUs)*2 | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the communication bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the communication bus check.*1 | |
| Sub bus (gateway function equipped ECU that has history of connected ECUs)*3 | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
| |
| Not displayed | Either of the following:
|
Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.
| HOW TO INTERPRET BUS CHECK (COMMUNICATION BUS CHECK) SCREEN |
When a communication stop is currently occurring, the probable malfunctioning part can be determined from the communication bus check and by using the following methods.
If a communication error of only 1 ECU or sensor is indicated on the Communication Bus Check screen, a communication stop of the ECU or sensor is suspected.
Example: Open in both CAN branch lines of ECU B on the V bus

| *a | V Bus | *b | Sub bus |
| *c | Terminating Resistor | *d | Location of malfunction |
| *e | Not displayed or background color changes to red or yellow | *f | Communication Bus Check screen |
![]() |
If communication errors for multiple ECUs or sensors are indicated on the Communication Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or a sensor which is not displayed) is suspected.
Example: Open in a CAN branch line for ECU D on the V bus
| *a | Background color periodically changes to yellow or red |
| *b | Not displayed or background color is yellow or red |
| *c | Not displayed |
| Bus Type | Background Color | Connection Status |
| V Bus | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the communication bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the communication bus check.*1 | |
| Sub bus (gateway function equipped ECU that does not have history of connected ECUs)*2 | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the communication bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the communication bus check.*1 | |
| Sub bus (gateway function equipped ECU that has history of connected ECUs)*3 | White | Communication has been normal since the start of the communication bus check. |
| Yellow | Communication stop occurred at least once since the start of the communication bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
| |
| Not displayed | Either of the following:
|
![]() |
If a communication error is indicated on both the V bus and sub bus on the Communication Bus Check screen, suspect any communication stop displayed for the V bus first.
Example: Open in both CAN branch lines of ECU C on the V bus
| *a | Not displayed or background color changes to red |
![]() |
If the Communication Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.
Example: Open in both CAN branch lines of ECU G on the sub bus
| *a | Background color changes to red |
If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the Communication Bus Check screen.
(In this case, ECU A and B are not displayed or their background color changes to red.)

| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of malfunction |
| *e | Not displayed or background color is red | *f | Communication Bus Check screen |
If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the Communication Bus Check screen.
(In this case, ECU I and J are not displayed or their background color changes to red.)

| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of malfunction |
| *e | Not displayed or background color is red | *f | Communication Bus Check screen |
| *g | Gateway function equipped ECU | - | - |
![]() |
When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the Communication Bus Check screen.
| *a | When any of the following malfunctions occur on the V bus |
| *b | When any of the following malfunctions occur on a sub bus |
| *c | Not displayed |
| Short between CAN lines (CANH and CANL) |
| Short between a CAN line (CANH or CANL) and +B |
| Short between a CAN line (CANH or CANL) and ground |
| Open in a CAN main bus line |
| BUS CHECK (COMMUNICATION MALFUNCTION DTC) |
![]() |
Select "Bus Check" from the "System Select" screen on the intelligent tester.
![]() |
Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".
![]() |
Select the system to be checked for DTCs and select "Details".
![]() |
CAN communication system DTCs are output.
| HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U) |
If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.
If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.

| *a | Items to be checked | - | - |
If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.

| *a | Items to be checked | - | - |
To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.

| *a | Items to be checked | *b | ECM |
| *c | Gateway function equipped ECU | *d | Location of malfunction |
| *e | V Bus | *f | Sub bus |
When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.
| DTC TABLE BY ECU |
ECM (for 1AZ-FE)
ECM (for 2AR-FE) / Intelligent Tester Display "Engine and ECT"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100*1 | Lost Communication with ECM / PCM "A" | The transmission control ECU does not receive data from the engine control ECU for 1.25 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait 5 seconds or more. | MIL illuminates. | DTC remains stored only while malfunction is occurring. |
| U0101*2 | Lost Communication with TCM | The engine control ECU does not receive data from the transmission control ECU for 1.25 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait 5 seconds or more. | MIL illuminates. | DTC remains stored only while malfunction is occurring. |
ECM (for 2GR-FE) / Intelligent Tester Display "Engine"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0101*1 | Lost Communication with TCM | The ECM does not receive data from the TCM for 1.25 seconds or more. | Both conditions are met:
| Turn the engine switch on (IG) and wait 5 seconds or more. | MIL illuminates. | DTC remains stored only while malfunction is occurring. |
TCM (for 2GR-FE) / Intelligent Tester Display "ECT"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100*1 | Lost Communication with ECM / PCM "A" | The TCM does not receive data from the ECM for 1.25 seconds or more. | Both conditions are met:
| Turn the engine switch on (IG) and wait 5 seconds or more. | MIL illuminates. | DTC remains stored only while malfunction is occurring. |
Power Steering ECU with Motor Assembly / Intelligent Tester Display "EMPS"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM "A" | The power steering ECU with motor assembly does not receive data from the ECM for 5 minutes or more. | All conditions are met:
| Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
| U0129 | Lost Communication with Brake System Control Module | The power steering ECU with motor assembly cannot receive data from the brake actuator assembly for 2.34 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 6 seconds. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
Brake Actuator Assembly / Intelligent Tester Display "ABS/VSC/TRC"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0073 | Control Module Communication Bus OFF | Bus off is judged for 0.1 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and check that the initial light check illumination turns off, and then wait at least 3 seconds. |
| DTC is stored until it is cleared using the intelligent tester. |
| U0100 | Lost Communication with ECM / PCM | The brake actuator assembly does not receive data from the ECM for 2.5 seconds or more. | All conditions are met:
| Turn the ignition switch to ON and drive the vehicle at a speed of 6 km/h (4 mph) or more for 6 seconds or more. Check that the warning light remains off after turning off following the initial light check. | Slip indicator light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The brake actuator assembly does not receive data from the airbag sensor assembly for 1.1 seconds or more. | All conditions are met:
| Turn the ignition switch to ON and drive the vehicle at a speed of 6 km/h (4 mph) or more for 3 seconds or more. Check that the warning light remains off after turning off following the initial light check. | Slip indicator light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The brake actuator assembly does not receive data from the steering sensor for 1.1 seconds or more. | All conditions are met:
| Turn the ignition switch to ON and drive the vehicle at a speed of 6 km/h (4 mph) or more for 3 seconds or more. Check that the warning light remains off after turning off following the initial light check. | Slip indicator light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
Steering Sensor / Intelligent Tester Display "Steering Angle Sensor"
Airbag Sensor Assembly / Intelligent Tester Display "SRS Airbag"
Main Body ECU (Multiplex network body ECU) / Intelligent Tester Display "Main Body"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM "A" | The main body ECU (multiplex network body ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0101 | Lost Communication with TCM | The main body ECU (multiplex network body ECU) does not receive data from the TCM for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0120 | Lost Communication with Starter / Generator Control Module | The main body ECU (multiplex network body ECU) does not receive data from the smart key ECU assembly (certification ECU) for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0151 | Lost Communication with Restraints Control Module | The main body ECU (multiplex network body ECU) does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The main body ECU (multiplex network body ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0164 | Lost Communication with HVAC Control Module | The main body ECU (multiplex network body ECU) does not receive data from the air conditioning amplifier assembly for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0182 | Lost Communication with AFS ECU | The main body ECU (multiplex network body ECU) does not receive data from the AFS ECU for 5 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0327 | Software Incompatibility with Vehicle Security Control Module | The main body ECU (multiplex network body ECU) does not receive data from the smart key ECU assembly (certification ECU) for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U1002 | Lost Communication with Gateway Module (Main body) | The main body ECU (multiplex network body ECU) does not receive data from ECUs with a sub bus 1 connection record for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U1115 | Lost Communication with Tilt and Telescopic Module | The main body ECU (multiplex network body ECU) does not receive data from the multiplex tilt and telescopic ECU for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
Smart Key ECU Assembly (Certification ECU) / Intelligent Tester Display "Entry & Start"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM | The smart key ECU assembly (certification ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0142 | Lost Communication with Main Body ECU | The smart key ECU assembly (certification ECU) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Combination Meter | The smart key ECU assembly (certification ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
Smart Key ECU Assembly (Certification ECU) / Intelligent Tester Display "Power Source Control "
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM | The smart key ECU assembly (certification ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0140 | Lost Communication with Main Body ECU | The smart key ECU assembly (certification ECU) does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Combination Meter | The smart key ECU assembly (certification ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
Air Conditioning Amplifier Assembly / Intelligent Tester Display "Air Conditioner"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM | The air conditioning amplifier assembly does not receive data from the ECM for 5 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0131 | Lost Communication with Electric Power Steering ECU | The air conditioning amplifier assembly does not receive data from the power steering ECU with motor assembly for 5 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0142 | Lost Communication with Main Body ECU | The air conditioning amplifier assembly does not receive data from the Main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Combination Meter | The air conditioning amplifier assembly does not receive data from the combination meter assembly for 5 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
Combination Meter Assembly / Intelligent Tester Display "Combination Meter"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM "A" | The combination meter assembly does not receive data from the ECM for 2 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 2 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0129 | Lost Communication with Skid Control ECU | The combination meter assembly does not receive data from the brake actuator assembly for 3 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 3 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0131 | Lost Communication with Power Steering Control Module | The combination meter assembly does not receive data from the power steering ECU with motor assembly for 3 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 3 seconds. | EPS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0142 | Lost Communication with Main Body ECU | The combination meter assembly does not receive data from the Main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 3 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0151 | Lost Communication with Airbag ECU | The combination meter assembly does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10 seconds. | SRS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
Navigation ECU Sub-Assembly (for Navigation receiver type) / Intelligent Tester Display "Navigation System"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0073 | Sending Malfunction (Navigation to APGS) | The navigation ECU sub-assembly does not send/receive data 10 times in succession. | Both conditions are met:
| Turn the ignition switch to ACC and wait at least 11 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0100 | Lost Communication with ECM | The navigation ECU sub-assembly does not receive data from the ECM for 4 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The navigation ECU sub-assembly does not receive data from the steering sensor for 1.12 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 2.12 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0140 | Lost Communication with Body Control Module | The navigation ECU sub-assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Meter ECU Communication | The navigation ECU sub-assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 31 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
Radio and Display Receiver Assembly (for Radio and display type) / Intelligent Tester Display "Navigation System"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0073 | Sending Malfunction (Navigation to APGS) | The radio and display receiver assembly does not send/receive data 10 times in succession. | Both conditions are met:
| Turn the ignition switch to ACC and wait at least 11 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0100 | Lost Communication with ECM | The radio and display receiver assembly does not receive data from the ECM for 4 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0140 | Lost Communication with Body Control Module | The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Meter ECU Communication | The radio and display receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 31 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
AFS ECU / Intelligent Tester Display "AFS"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0073 | Control Module Communication Bus Off | The AFS ECU does not send/receive data 10 times in succession. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 13 seconds. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0100 | Lost Communication with ECM | The AFS ECU does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 13 seconds. | AFS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0101 | Lost Communication with TCM | The AFS ECU does not receive data from the TCM for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 13 seconds. | AFS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The AFS ECU does not receive data from the steering sensor for 5 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 8 seconds. | AFS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0129 | Lost Communication with Skid Control ECU | The AFS ECU does not receive data from the brake actuator assembly for 5 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 13 seconds. | AFS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U0142 | Lost Communication with Main Body ECU | The AFS ECU does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 13 seconds. | AFS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
| U1000*1 | Can Communication Failure(Message Registry) | The AFS ECU does not send/receive data 10 times in succession. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 13 seconds. | AFS warning light illuminates. | DTC is stored until it is cleared using the intelligent tester. |
Clearance Warning ECU Assembly / Intelligent Tester Display "Clearance Sonar"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0100 | Lost Communication with ECM / PCM "A" | The clearance warning ECU assembly does not receive data from the ECM for 5.75 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 7.75 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0101 | Lost Communication with TCM | The clearance warning ECU assembly does not receive data from the TCM for 8.07 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 10.07 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0142 | Lost Communication with Body Control Module "B" | The clearance warning ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 5.9 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 7.9 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| U0155 | Lost Communication with Instrument Panel Cluster Control Module (Combination Meter) | The clearance warning ECU assembly does not receive data from the combination meter assembly for 6.5 seconds or more. | Both conditions are met:
| Turn the ignition switch to ON and wait at least 8.5 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
Multiplex Tilt and Telescopic ECU / Intelligent Tester Display "Tilt & Telescopic"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
| U0142 | Lost Communication with Main Body ECU | The multiplex tilt and telescopic ECU does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | The power source voltage of the multiplex tilt and telescopic ECU is 10.1 V or more. | Turn the ignition switch to ON and wait at least 10 seconds or more. | - | DTC is stored until it is cleared using the intelligent tester. |
| DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF V BUS, PAST COMMUNICATION ERROR) |
Regarding a past communication error of an ECU or sensor connected to the V bus (in this case, normal is displayed when performing the communication bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.
| - | Trouble Mode | |||||
| V Bus (Open in one CAN branch line) | ||||||
| Output ECU | Output DTC | Center Airbag Sensor Communication Stop Mode (Click here) | Air Conditioning Amplifier Communication Stop Mode (Click here) | AFS ECU Communication Stop Mode (Click here) | Navigation ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | โ | - | - | |
| U0131 | - | โ | - | - | ||
| U0142 | - | โ | - | - | ||
| U0155 | - | โ | - | - | ||
| AFS ECU | U0073 | - | - | - | - | |
| U0100 | - | - | โ | - | ||
| U0101 | - | - | โ | - | ||
| U0126 | - | - | โ | - | ||
| U0129 | - | - | โ | - | ||
| U0142 | - | - | โ | - | ||
| U0073 | - | - | - | โ | |
| U0100 | - | - | - | โ | ||
| U0126*2 | X | X | X | โ | ||
| U0140 | - | - | - | โ | ||
| U0155 | - | - | - | โ | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - | - | |
| U0101 | - | - | - | - | ||
| U0120 | - | - | - | - | ||
| U0151 | โ | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0164 | - | โ | - | - | ||
| U0182 | - | - | โ | - | ||
| U0327 | - | - | - | - | ||
| V Bus | Clearance Warning ECU Assembly | U0100 | - | - | - | - |
| U0101 | - | - | - | - | ||
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| ECM | - | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | - | - | |
| U0129 | - | - | - | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | |
| U0140 | - | - | - | - | ||
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | |
| U0129 | - | - | - | - | ||
| U0131 | - | - | - | - | ||
| U0142 | - | - | - | - | ||
| U0151 | โ | - | - | - | ||
| Steering Sensor | - | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | - | |
| U0100 | โ | โ | โ | โ | ||
| U0123 | โ | โ | โ | โ | ||
| U0126 | โ | โ | โ | โ | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | - | - | |
| U1115 | - | - | - | - | ||
| - | Trouble Mode | ||||
| V Bus (Open in one CAN branch line) | |||||
| Output ECU | Output DTC | Audio Receiver Assembly Communication Stop Mode (Click here) | Main Body ECU Communication Stop Mode (Click here) | Clearance Warning ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | - | - | - | ||
| U0142 | - | โ | - | ||
| U0155 | - | - | - | ||
| AFS ECU | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0101 | - | - | - | ||
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | โ | - | ||
| V Bus |
| U0073 | โ | - | - |
| U0100 | โ | - | - | ||
| U0126*2 | โ | X | X | ||
| U0140 | โ | โ | - | ||
| U0155 | โ | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | โ | - | |
| U0101 | - | โ | - | ||
| U0120 | - | โ | - | ||
| U0151 | - | โ | - | ||
| U0155 | - | โ | - | ||
| U0164 | - | โ | - | ||
| U0182 | - | โ | - | ||
| U0327 | - | โ | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | โ | |
| U0101 | - | - | โ | ||
| U0142 | - | โ | โ | ||
| U0155 | - | - | โ | ||
| ECM | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | |
| U0140 | - | โ | - | ||
| U0142 | - | โ | - | ||
| U0155 | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | โ | - | ||
| U0151 | - | - | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | |
| U0100 | โ | โ | โ | ||
| U0123 | โ | โ | โ | ||
| U0126 | โ | โ | โ | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | - | |
| U1115 | - | - | - | ||
| - | Trouble Mode (Open in one CAN branch line) | ||||
| V Bus | |||||
| Output ECU | Output DTC | Power Steering ECU Communication Stop Mode (Click here) | Certification ECU Communication Stop Mode (Click here) | Steering Angle Sensor Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | โ | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| AFS ECU | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0101 | - | - | - | ||
| U0126 | - | - | โ | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0126*2 | X | X | โ | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | โ | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0182 | - | - | - | ||
| U0327 | - | โ | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| ECM | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | โ | - | - | |
| U0129 | โ | - | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | X | โ | - | |
| U0140 | - | โ | - | ||
| U0142 | - | โ | - | ||
| U0155 | - | โ | - | ||
| V Bus | Combination Meter Assembly | U0100 | - | - | - |
| U0129 | X | - | - | ||
| U0131 | โ | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | |
| U0100 | โ | โ | โ | ||
| U0123 | โ | โ | โ | ||
| U0126 | โ | โ | โ | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | - | |
| U1115 | - | - | - | ||
| - | Trouble Mode (Open in one CAN branch line) | |||
| V Bus | ||||
| Output ECU | Output DTC | Skid Control ECU Communication Stop Mode (Click here) | DLC3 | |
| V Bus | Airbag Sensor Assembly | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | |
| U0131 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| AFS ECU | U0073 | - | - | |
| U0100 | - | - | ||
| U0101 | - | - | ||
| U0126 | - | - | ||
| U0129 | โ | - | ||
| U0142 | - | - | ||
| U0073 | - | - | |
| U0100 | - | - | ||
| U0126*2 | X | X | ||
| U0140 | - | - | ||
| U0155 | - | - | ||
| V Bus | Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - |
| U0101 | - | - | ||
| U0120 | - | - | ||
| U0151 | - | - | ||
| U0155 | - | - | ||
| U0164 | - | - | ||
| U0182 | - | - | ||
| U0327 | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | |
| U0101 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| ECM | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | |
| U0129 | โ | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | X | - | |
| U0140 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| Combination meter assembly | U0100 | - | - | |
| U0129 | โ | - | ||
| U0131 | - | - | ||
| U0142 | - | - | ||
| U0151 | - | - | ||
| Steering Sensor | - | - | - | |
| Brake Actuator Assembly | U0073 | โ | - | |
| U0100 | โ | โ | ||
| U0123 | โ | โ | ||
| U0126 | โ | โ | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | |
| U1115 | - | - | ||
| - | Trouble Mode (Open in both CAN branch lines) | |||||
| V Bus | ||||||
| Output ECU | Output DTC | Center Airbag Sensor Communication Stop Mode (Click here) | Air Conditioning Amplifier Communication Stop Mode (Click here) | AFS ECU Communication Stop Mode (Click here) | Navigation ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | โ | - | - | |
| U0131 | - | โ | - | - | ||
| U0142 | - | โ | - | - | ||
| U0155 | - | โ | - | - | ||
| AFS ECU | U0073 | - | - | โ | - | |
| U0100 | - | - | โ | - | ||
| U0101 | - | - | โ | - | ||
| U0126 | - | - | โ | - | ||
| U0129 | - | - | โ | - | ||
| U0142 | - | - | โ | - | ||
| U0073 | - | - | - | โ | |
| U0100 | - | - | - | โ | ||
| U0126*2 | - | - | - | โ | ||
| U0140 | - | - | - | โ | ||
| U0155 | - | - | - | โ | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - | - | |
| U0101 | - | - | - | - | ||
| U0120 | - | - | - | - | ||
| U0151 | โ | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0164 | - | โ | - | - | ||
| U0182 | - | - | โ | - | ||
| U0327 | - | - | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | - | |
| U0101 | - | - | - | - | ||
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| ECM | - | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | - | - | |
| U0129 | - | - | - | - | ||
| V Bus | Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - |
| U0140 | - | - | - | - | ||
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | |
| U0129 | - | - | - | - | ||
| U0131 | - | - | - | - | ||
| U0142 | - | - | - | - | ||
| U0151 | โ | - | - | - | ||
| Steering Sensor | - | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | - | |
| U0100 | - | - | - | - | ||
| U0123 | โ | - | - | - | ||
| U0126 | - | - | - | - | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | - | - | |
| U1115 | - | - | - | - | ||
| - | Trouble Mode (Open in both CAN branch lines) | ||||
| V Bus | |||||
| Output ECU | Output DTC | Audio Receiver Assembly Communication Stop Mode (Click here) | Main Body ECU Communication Stop Mode (Click here) | Clearance Warning ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | - | - | - | ||
| U0142 | - | โ | - | ||
| U0155 | - | - | - | ||
| AFS ECU | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0101 | - | - | - | ||
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | โ | - | ||
| V Bus |
| U0073 | โ | - | - |
| U0100 | โ | - | - | ||
| U0126*2 | โ | - | - | ||
| U0140 | โ | โ | - | ||
| U0155 | โ | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | โ | - | |
| U0101 | - | โ | - | ||
| U0120 | - | โ | - | ||
| U0151 | - | โ | - | ||
| U0155 | - | โ | - | ||
| U0164 | - | โ | - | ||
| U0182 | - | โ | - | ||
| U0327 | - | โ | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | โ | |
| U0101 | - | - | โ | ||
| U0142 | - | โ | โ | ||
| U0155 | - | - | โ | ||
| ECM | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | |
| U0140 | - | โ | - | ||
| U0142 | - | โ | - | ||
| U0155 | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | โ | - | ||
| U0151 | - | - | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0123 | - | - | - | ||
| U0126 | - | - | - | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | - | |
| U1115 | - | - | - | ||
| - | Trouble Mode (Open in both CAN branch lines) | ||||
| V Bus | |||||
| Output ECU | Output DTC | Power Steering ECU Communication Stop Mode (Click here) | Certification ECU Communication Stop Mode (Click here) | Steering Angle Sensor Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | โ | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| AFS ECU | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0101 | - | - | - | ||
| U0126 | - | - | โ | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0126*2 | - | - | โ | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | โ | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0182 | - | - | - | ||
| U0327 | - | โ | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| V Bus | ECM | - | - | - | - |
| Power Steering ECU with Motor Assembly | U0100 | โ | - | - | |
| U0129 | โ | - | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | โ | - | |
| U0140 | - | โ | - | ||
| U0142 | - | โ | - | ||
| U0155 | - | โ | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | โ | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | |
| U0100 | - | - | โ | ||
| U0123 | - | - | - | ||
| U0126 | - | - | โ | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | - | |
| U1115 | - | - | - | ||
| - | Trouble Mode (Open in both CAN branch lines) | |||
| V Bus | ||||
| Output ECU | Output DTC | Skid Control ECU Communication Stop Mode (Click here) | DLC3 | |
| V Bus | Airbag Sensor Assembly | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | |
| U0131 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| AFS ECU | U0073 | - | - | |
| U0100 | - | - | ||
| U0101 | - | - | ||
| U0126 | - | - | ||
| U0129 | โ | - | ||
| U0142 | - | - | ||
| U0073 | - | - | |
| U0100 | - | - | ||
| U0126*2 | - | - | ||
| U0140 | - | - | ||
| U0155 | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | |
| U0101 | - | - | ||
| U0120 | - | - | ||
| U0151 | - | - | ||
| U0155 | - | - | ||
| U0164 | - | - | ||
| U0182 | - | - | ||
| U0327 | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | |
| U0101 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| ECM | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | |
| U0129 | โ | - | ||
| V Bus | Smart Key ECU Assembly (Certification ECU) | U0100 | - | - |
| U0140 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| Combination Meter Assembly | U0100 | - | - | |
| U0129 | โ | - | ||
| U0131 | - | - | ||
| U0142 | - | - | ||
| U0151 | - | - | ||
| Steering Sensor | - | - | - | |
| Brake Actuator Assembly | U0073 | โ | - | |
| U0100 | โ | - | ||
| U0123 | โ | - | ||
| U0126 | โ | - | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | |
| U1115 | - | - | ||
| - | Trouble Mode (Open in one CAN main bus line) | ||||
| V Bus | |||||
| Output ECU | Output DTC | Combination Meter ECU Communication Stop Mode (Click here) | CAN No. 1 J/C to CAN No. 2 J/C | ECM Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | โ | |
| U0131 | - | - | โ | ||
| U0142 | - | โ | - | ||
| U0155 | - | โ | - | ||
| AFS ECU | U0073 | - | - | - | |
| U0100 | - | โ | โ | ||
| U0101 | - | โ | โ | ||
| U0126 | - | - | - | ||
| U0129 | - | โ | - | ||
| U0142 | - | - | - | ||
| V Bus |
| U0073 | - | โ | - |
| U0100 | - | - | โ | ||
| U0126*2 | X | โ | X | ||
| U0140 | X | โ | - | ||
| U0155 | โ | โ | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | โ | โ | |
| U0101 | - | โ | โ | ||
| U0120 | - | โ | - | ||
| U0151 | - | - | - | ||
| U0155 | โ | - | - | ||
| U0164 | - | โ | - | ||
| U0182 | - | - | - | ||
| U0327 | - | โ | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | โ | |
| U0101 | - | - | โ | ||
| U0142 | - | โ | - | ||
| U0155 | โ | โ | - | ||
| ECM | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | โ | โ | |
| U0129 | - | โ | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | โ | |
| U0140 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | โ | โ | - | ||
| Combination Meter Assembly | U0100 | โ | โ | โ | |
| U0129 | โ | โ | - | ||
| U0131 | โ | - | - | ||
| U0142 | โ | - | - | ||
| U0151 | โ | - | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | |
| U0100 | โ | โ | โ | ||
| U0123 | โ | โ | โ | ||
| U0126 | โ | โ | โ | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | - | |
| U1115 | - | - | - | ||
| - | Trouble Mode (Open in both CAN main bus lines) | ||||
| V Bus | |||||
| Output ECU | Output DTC | Combination Meter ECU Communication Stop Mode (Click here) | CAN No. 1 J/C to CAN No. 2 J/C | ECM Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | โ | |
| U0131 | - | โ | - | ||
| U0142 | - | โ | - | ||
| U0155 | โ | โ | - | ||
| AFS ECU | U0073 | - | - | - | |
| U0100 | - | โ | โ | ||
| U0101 | - | โ | โ | ||
| U0126 | - | - | - | ||
| U0129 | - | โ | - | ||
| U0142 | - | - | - | ||
| U0073 | - | - | - | |
| U0100 | - | - | โ | ||
| U0126*2 | - | โ | - | ||
| U0140 | - | โ | - | ||
| U0155 | โ | โ | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | โ | โ | |
| U0101 | - | โ | โ | ||
| U0120 | - | โ | - | ||
| U0151 | - | - | - | ||
| U0155 | โ | - | - | ||
| U0164 | - | โ | - | ||
| U0182 | - | - | - | ||
| U0327 | - | โ | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | โ | |
| U0101 | - | - | โ | ||
| U0142 | - | โ | - | ||
| U0155 | โ | โ | - | ||
| ECM | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | โ | โ | |
| U0129 | - | โ | - | ||
| V Bus | Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | โ |
| U0140 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | โ | โ | - | ||
| Combination Meter Assembly | U0100 | โ | โ | โ | |
| U0129 | โ | โ | - | ||
| U0131 | โ | - | - | ||
| U0142 | โ | - | - | ||
| U0151 | โ | - | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | |
| U0100 | - | โ | โ | ||
| U0123 | - | โ | - | ||
| U0126 | - | โ | - | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | - | - | |
| U1115 | - | - | - | ||
| - | Trouble Mode (CAN bus line short circuit or short to GND) | ||
| V Bus | |||
| Output ECU | Output DTC | CAN No. 1 J/C to CAN No. 2 J/C | |
| V Bus | Airbag Sensor Assembly | - | - |
| Air Conditioning Amplifier Assembly | U0100 | โ | |
| U0131 | โ | ||
| U0142 | โ | ||
| U0155 | โ | ||
| AFS ECU | U0073 | โ | |
| U0100 | โ | ||
| U0101 | โ | ||
| U0126 | โ | ||
| U0129 | โ | ||
| U0142 | โ | ||
| V Bus |
| U0073 | โ |
| U0100 | โ | ||
| U0126*2 | โ | ||
| U0140 | โ | ||
| U0155 | โ | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | โ | |
| U0101 | โ | ||
| U0120 | โ | ||
| U0151 | โ | ||
| U0155 | โ | ||
| U0164 | โ | ||
| U0182 | โ | ||
| U0327 | โ | ||
| Clearance Warning ECU Assembly | U0100 | โ | |
| U0101 | โ | ||
| U0142 | โ | ||
| U0155 | โ | ||
| ECM | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | โ | |
| U0129 | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | โ | |
| U0140 | โ | ||
| U0142 | โ | ||
| U0155 | โ | ||
| Combination Meter Assembly | U0100 | โ | |
| U0129 | โ | ||
| U0131 | โ | ||
| U0142 | โ | ||
| U0151 | โ | ||
| Steering Sensor | - | - | |
| Brake Actuator Assembly | U0073 | โ | |
| U0100 | โ | ||
| U0123 | โ | ||
| U0126 | โ | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | - | |
| U1115 | - | ||
| - | Trouble Mode | |||||
| V Bus (Open in one CAN branch line) | ||||||
| Output ECU | Output DTC | Center Airbag Sensor Communication Stop Mode (Click here) | Air Conditioning Amplifier Communication Stop Mode (Click here) | Audio Receiver Assembly Communication Stop Mode (Click here) | Main Body ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | โ | - | - | |
| U0131 | - | โ | - | - | ||
| U0142 | - | โ | - | โ | ||
| U0155 | - | โ | - | - | ||
| Radio and Display Receiver Assembly (for Radio and Display Type) | U0073 | - | - | โ | - | |
| U0100 | - | - | โ | - | ||
| U0140 | - | - | โ | โ | ||
| U0155 | - | - | โ | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - | โ | |
| U0101 | - | - | - | โ | ||
| U0120 | - | - | - | โ | ||
| U0151 | โ | - | - | โ | ||
| U0155 | - | - | - | โ | ||
| U0164 | - | โ | - | โ | ||
| U0327 | - | - | - | โ | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | - | |
| U0101 | - | - | - | - | ||
| U0142 | - | - | - | โ | ||
| U0155 | - | - | - | - | ||
| ECM | - | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | - | - | |
| U0129 | โ | โ | โ | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | |
| U0140 | - | - | - | โ | ||
| U0142 | - | - | - | โ | ||
| U0155 | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | |
| U0129 | โ | โ | โ | โ | ||
| U0131 | - | - | - | - | ||
| U0142 | - | - | - | โ | ||
| U0151 | โ | - | - | - | ||
| Steering Sensor | - | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | - | |
| U0100 | โ | โ | โ | โ | ||
| U0123 | โ | โ | โ | โ | ||
| U0126 | โ | โ | โ | โ | ||
| - | Trouble Mode (Open in one CAN branch line) | |||||
| V Bus | ||||||
| Output ECU | Output DTC | Clearance Warning ECU Communication Stop Mode (Click here) | Power Steering ECU Communication Stop Mode (Click here) | Certification ECU Communication Stop Mode (Click here) | Steering Angle Sensor Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | - | |
| U0131 | - | โ | - | - | ||
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| Radio and Display Receiver Assembly (for Radio and Display Type) | U0073 | - | - | - | - | |
| U0100 | - | - | - | - | ||
| U0140 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - | - | |
| U0101 | - | - | - | - | ||
| U0120 | - | - | โ | - | ||
| U0151 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0164 | - | - | - | - | ||
| U0327 | - | - | โ | - | ||
| Clearance Warning ECU Assembly | U0100 | โ | - | - | - | |
| U0101 | โ | - | - | - | ||
| U0142 | โ | - | - | - | ||
| U0155 | โ | - | - | - | ||
| ECM | - | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | โ | - | - | |
| U0129 | โ | โ | โ | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | โ | - | |
| U0140 | - | - | โ | - | ||
| U0142 | - | - | โ | - | ||
| U0155 | - | - | โ | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | |
| U0129 | โ | โ | โ | โ | ||
| U0131 | - | โ | - | - | ||
| U0142 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| Steering Sensor | - | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | - | |
| U0100 | โ | โ | โ | โ | ||
| U0123 | โ | โ | โ | โ | ||
| U0126 | โ | โ | โ | โ | ||
| - | Trouble Mode (Open in one CAN branch line) | |||
| V Bus | ||||
| Output ECU | Output DTC | Skid Control ECU Communication Stop Mode (Click here) | DLC3 | |
| V Bus | Airbag Sensor Assembly | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | |
| U0131 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| Radio and Display Receiver Assembly (for Radio and Display Type) | U0073 | - | - | |
| U0100 | - | - | ||
| U0140 | - | - | ||
| U0155 | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | |
| U0101 | - | - | ||
| U0120 | - | - | ||
| U0151 | - | - | ||
| U0155 | - | - | ||
| U0164 | - | - | ||
| U0327 | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | |
| U0101 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| ECM | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | |
| U0129 | โ | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | |
| U0140 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| Combination meter assembly | U0100 | - | - | |
| U0129 | โ | โ | ||
| U0131 | - | - | ||
| U0142 | - | - | ||
| U0151 | - | - | ||
| Steering Sensor | - | - | - | |
| Brake Actuator Assembly | U0073 | โ | - | |
| U0100 | โ | โ | ||
| U0123 | โ | โ | ||
| U0126 | โ | โ | ||
| - | Trouble Mode (Open in both CAN branch lines) | |||||
| V Bus | ||||||
| Output ECU | Output DTC | Center Airbag Sensor Communication Stop Mode (Click here) | Air Conditioning Amplifier Communication Stop Mode (Click here) | Audio Receiver Assembly Communication Stop Mode (Click here) | Main Body ECU Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | โ | - | - | |
| U0131 | - | โ | - | - | ||
| U0142 | - | โ | - | โ | ||
| U0155 | - | โ | - | - | ||
| Radio and Display Receiver Assembly (for Radio and Display Type) | U0073 | - | - | โ | - | |
| U0100 | - | - | โ | - | ||
| U0140 | - | - | โ | โ | ||
| U0155 | - | - | โ | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - | โ | |
| U0101 | - | - | - | โ | ||
| U0120 | - | - | - | โ | ||
| U0151 | โ | - | - | โ | ||
| U0155 | - | - | - | โ | ||
| U0164 | - | โ | - | โ | ||
| U0327 | - | - | - | โ | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | - | |
| U0101 | - | - | - | - | ||
| U0142 | - | - | - | โ | ||
| U0155 | - | - | - | - | ||
| ECM | - | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | - | - | |
| U0129 | โ | โ | โ | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | - | |
| U0140 | - | - | - | โ | ||
| U0142 | - | - | - | โ | ||
| U0155 | - | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | |
| U0129 | โ | โ | โ | โ | ||
| U0131 | - | - | - | - | ||
| U0142 | - | - | - | โ | ||
| U0151 | โ | - | - | - | ||
| Steering Sensor | - | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | - | |
| U0100 | - | - | - | - | ||
| U0123 | โ | - | - | - | ||
| U0126 | - | - | - | - | ||
| - | Trouble Mode (Open in both CAN branch lines) | |||||
| V Bus | ||||||
| Output ECU | Output DTC | Clearance Warning ECU Communication Stop Mode (Click here) | Power Steering ECU Communication Stop Mode (Click here) | Certification ECU Communication Stop Mode (Click here) | Steering Angle Sensor Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | - | |
| U0131 | - | โ | - | - | ||
| U0142 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| Radio and Display Receiver Assembly (for Radio and Display Type) | U0073 | - | - | - | - | |
| U0100 | - | - | - | - | ||
| U0140 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - | - | |
| U0101 | - | - | - | - | ||
| U0120 | - | - | โ | - | ||
| U0151 | - | - | - | - | ||
| U0155 | - | - | - | - | ||
| U0164 | - | - | - | - | ||
| U0327 | - | - | โ | - | ||
| Clearance Warning ECU Assembly | U0100 | โ | - | - | - | |
| U0101 | โ | - | - | - | ||
| U0142 | โ | - | - | - | ||
| U0155 | โ | - | - | - | ||
| ECM | - | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | โ | - | - | |
| U0129 | โ | โ | โ | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | โ | - | |
| U0140 | - | - | โ | - | ||
| U0142 | - | - | โ | - | ||
| U0155 | - | - | โ | - | ||
| Combination Meter Assembly | U0100 | - | - | - | - | |
| U0129 | โ | โ | โ | โ | ||
| U0131 | - | โ | - | - | ||
| U0142 | - | - | - | - | ||
| U0151 | - | - | - | - | ||
| Steering Sensor | - | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | - | |
| U0100 | - | - | - | โ | ||
| U0123 | - | - | - | - | ||
| U0126 | - | - | - | โ | ||
| - | Trouble Mode (Open in both CAN branch lines) | |||
| V Bus | ||||
| Output ECU | Output DTC | Skid Control ECU Communication Stop Mode (Click here) | DLC3 | |
| V Bus | Airbag Sensor Assembly | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | |
| U0131 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| Radio and Display Receiver Assembly (for Radio and Display Type) | U0073 | - | - | |
| U0100 | - | - | ||
| U0140 | - | - | ||
| U0155 | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | |
| U0101 | - | - | ||
| U0120 | - | - | ||
| U0151 | - | - | ||
| U0155 | - | - | ||
| U0164 | - | - | ||
| U0327 | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | |
| U0101 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| ECM | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | |
| U0129 | โ | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | |
| U0140 | - | - | ||
| U0142 | - | - | ||
| U0155 | - | - | ||
| Combination Meter Assembly | U0100 | - | - | |
| U0129 | โ | โ | ||
| U0131 | - | - | ||
| U0142 | - | - | ||
| U0151 | - | - | ||
| Steering Sensor | - | - | - | |
| Brake Actuator Assembly | U0073 | โ | - | |
| U0100 | โ | - | ||
| U0123 | โ | - | ||
| U0126 | โ | - | ||
| - | Trouble Mode (Open in one CAN main bus line) | ||||
| V Bus | |||||
| Output ECU | Output DTC | Combination Meter ECU Communication Stop Mode (Click here) | CAN No. 1 J/C to CAN No. 2 J/C | ECM Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | โ | |
| U0131 | - | - | โ | ||
| U0142 | - | - | - | ||
| U0155 | โ | โ | - | ||
| Radio and Display Receiver Assembly (for Radio and Display Type) | U0073 | - | - | - | |
| U0100 | - | - | โ | ||
| U0140 | X | - | - | ||
| U0155 | โ | โ | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | โ | |
| U0101 | - | - | โ | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | โ | - | - | ||
| U0164 | - | โ | - | ||
| U0327 | - | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | โ | โ | |
| U0101 | - | โ | โ | ||
| U0142 | - | โ | - | ||
| U0155 | โ | - | - | ||
| ECM | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | โ | โ | |
| U0129 | - | โ | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | โ | |
| U0140 | - | โ | - | ||
| U0142 | - | โ | - | ||
| U0155 | โ | - | - | ||
| Combination Meter Assembly | U0100 | โ | โ | โ | |
| U0129 | โ | โ | โ | ||
| U0131 | โ | โ | - | ||
| U0142 | โ | โ | - | ||
| U0151 | โ | โ | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | |
| U0100 | โ | โ | โ | ||
| U0123 | โ | โ | โ | ||
| U0126 | โ | โ | โ | ||
| - | Trouble Mode (Open in both CAN main bus lines) | ||||
| V Bus | |||||
| Output ECU | Output DTC | Combination Meter ECU Communication Stop Mode (Click here) | CAN No. 1 J/C to CAN No. 2 J/C | ECM Communication Stop Mode (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | โ | |
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | โ | โ | - | ||
| Radio and Display Receiver Assembly (for Radio and Display Type) | U0073 | - | - | - | |
| U0100 | - | - | โ | ||
| U0140 | - | - | - | ||
| U0155 | โ | โ | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | โ | |
| U0101 | - | - | โ | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | โ | โ | - | ||
| U0164 | - | - | - | ||
| U0327 | - | โ | - | ||
| Clearance Warning ECU Assembly | U0100 | - | โ | โ | |
| U0101 | - | โ | โ | ||
| U0142 | - | โ | - | ||
| U0155 | โ | - | - | ||
| ECM | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | โ | |
| U0129 | โ | โ | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | โ | โ | |
| U0140 | - | โ | - | ||
| U0142 | - | โ | - | ||
| U0155 | โ | - | - | ||
| Combination Meter Assembly | U0100 | โ | โ | โ | |
| U0129 | โ | โ | โ | ||
| U0131 | โ | โ | - | ||
| U0142 | โ | โ | - | ||
| U0151 | โ | โ | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | |
| U0100 | - | โ | โ | ||
| U0123 | - | โ | - | ||
| U0126 | - | - | - | ||
| - | Trouble Mode (CAN bus line short circuit or short to GND) | ||
| V Bus | |||
| Output ECU | Output DTC | CAN No. 1 J/C to CAN No. 2 J/C | |
| V Bus | Airbag Sensor Assembly | - | - |
| Air Conditioning Amplifier Assembly | U0100 | โ | |
| U0131 | โ | ||
| U0142 | โ | ||
| U0155 | โ | ||
| Radio and Display Receiver Assembly (for Radio and Display Type) | U0073 | โ | |
| U0100 | โ | ||
| U0140 | โ | ||
| U0155 | โ | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | โ | |
| U0101 | โ | ||
| U0120 | โ | ||
| U0151 | โ | ||
| U0155 | โ | ||
| U0164 | โ | ||
| U0327 | โ | ||
| Clearance Warning ECU Assembly | U0100 | โ | |
| U0101 | โ | ||
| U0142 | โ | ||
| U0155 | โ | ||
| ECM | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | โ | |
| U0129 | โ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | โ | |
| U0140 | โ | ||
| U0142 | โ | ||
| U0155 | โ | ||
| Combination Meter Assembly | U0100 | โ | |
| U0129 | โ | ||
| U0131 | โ | ||
| U0142 | โ | ||
| U0151 | โ | ||
| Steering Sensor | - | - | |
| Brake Actuator Assembly | U0073 | โ | |
| U0100 | โ | ||
| U0123 | โ | ||
| U0126 | โ | ||
| DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF SUB BUS, PAST COMMUNICATION ERROR) |
Regarding a past communication error of ECUs and sensors connected to sub bus 1 (in this case, normal is displayed when performing the communication bus check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the Main Body ECU (Multiplex Network Body ECU).
| - | Trouble Mode (Open in one CAN branch line) | ||
| Sub bus 1 | |||
| Output ECU | Output DTC | Multiplex tilt and telescopic ECU (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | |
| U0131 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| AFS ECU | U0073 | - | |
| U0100 | - | ||
| U0101 | - | ||
| U0126 | - | ||
| U0129 | - | ||
| U0142 | - | ||
| V Bus |
| U0073 | - |
| U0100 | - | ||
| U0126*2 | - | ||
| U0140 | - | ||
| U0155 | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | |
| U0101 | - | ||
| U0120 | - | ||
| U0151 | - | ||
| U0155 | - | ||
| U0164 | - | ||
| U0182 | - | ||
| U0327 | - | ||
| Clearance Warning ECU Assembly | U0100 | - | |
| U0101 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| ECM | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | |
| U0129 | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | |
| U0140 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| Combination meter assembly | U0100 | - | |
| U0129 | - | ||
| U0131 | - | ||
| U0142 | - | ||
| U0151 | - | ||
| Steering Sensor | - | - | |
| Brake Actuator Assembly | U0073 | - | |
| U0100 | - | ||
| U0123 | - | ||
| U0126 | - | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | โ |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | โ | |
| U1115 | โ | ||
| - | Trouble Mode (Open in both CAN branch lines) | ||
| Sub bus 1 | |||
| Output ECU | Output DTC | Multiplex tilt and telescopic ECU (Click here) | |
| V Bus | Airbag Sensor Assembly | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | |
| U0131 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| AFS ECU | U0073 | - | |
| U0100 | - | ||
| U0101 | - | ||
| U0126 | - | ||
| U0129 | - | ||
| U0142 | - | ||
| U0073 | - | |
| U0100 | - | ||
| U0126*2 | - | ||
| U0140 | - | ||
| U0155 | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | |
| U0101 | - | ||
| U0120 | - | ||
| U0151 | - | ||
| U0155 | - | ||
| U0164 | - | ||
| U0182 | - | ||
| U0327 | - | ||
| Clearance Warning ECU Assembly | U0100 | - | |
| U0101 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| ECM | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | |
| U0129 | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | |
| U0140 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| Combination Meter Assembly | U0100 | - | |
| U0129 | - | ||
| U0131 | - | ||
| U0142 | - | ||
| U0151 | - | ||
| Steering Sensor | - | - | |
| V Bus | Brake Actuator Assembly | U0073 | - |
| U0100 | - | ||
| U0123 | - | ||
| U0126 | - | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | โ |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | โ | |
| U1115 | โ | ||
| - | Trouble Mode (Open in one CAN main bus line) | ||||
| Sub bus 1 | |||||
| Output ECU | Output DTC | Main Body ECU (Multiplex Network Body ECU) (Click here) | CAN No. 3 J/C to CAN No. 4 J/C | CAN No. 5 J/C | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| AFS ECU | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0101 | - | - | - | ||
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0126*2 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| V Bus | Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0182 | - | - | - | ||
| U0327 | - | - | - | ||
| Clearance Warning ECU Assembly | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| ECM | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0123 | - | - | - | ||
| U0126 | - | - | - | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | โ | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | โ | โ | โ | |
| U1115 | โ | โ | โ | ||
| - | Trouble Mode (Open in both CAN main bus lines) | ||||
| Sub bus 1 | |||||
| Output ECU | Output DTC | Main Body ECU (Multiplex Network Body ECU) (Click here) | CAN No. 3 J/C to CAN No. 4 J/C | CAN No. 5 J/C | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| AFS ECU | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0101 | - | - | - | ||
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0126*2 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0182 | - | - | - | ||
| U0327 | - | - | - | ||
| Clearance Warning ECU Assembly | U0073 | - | - | - | |
| U0101 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| ECM | - | - | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| Steering Sensor | - | - | - | - | |
| V Bus | Brake Actuator Assembly | U0073 | - | - | - |
| U0100 | - | - | - | ||
| U0123 | - | - | - | ||
| U0126 | - | - | - | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | โ | - | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | โ | - | - | |
| U1115 | โ | โ | - | ||
| - | Trouble Mode (CAN bus line short circuit or short to GND) | ||
| Sub bus 1 | |||
| Output ECU | Output DTC | CAN No. 3 J/C to CAN No. 4 J/C | |
| V Bus | Airbag Sensor Assembly | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | |
| U0131 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| AFS ECU | U0073 | - | |
| U0100 | - | ||
| U0101 | - | ||
| U0126 | - | ||
| U0129 | - | ||
| U0142 | - | ||
| U0073 | - | |
| U0100 | - | ||
| U0126*2 | - | ||
| U0140 | - | ||
| U0155 | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | |
| U0101 | - | ||
| U0120 | - | ||
| U0151 | - | ||
| U0155 | - | ||
| U0164 | - | ||
| U0182 | - | ||
| U0327 | - | ||
| V Bus | Clearance Warning ECU Assembly | U0100 | - |
| U0101 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| ECM | - | - | |
| Power Steering ECU with Motor Assembly | U0100 | - | |
| U0129 | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | |
| U0140 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| Combination Meter Assembly | U0100 | - | |
| U0129 | - | ||
| U0131 | - | ||
| U0142 | - | ||
| U0151 | - | ||
| Steering Sensor | - | - | |
| Brake Actuator Assembly | U0073 | - | |
| U0100 | - | ||
| U0123 | - | ||
| U0126 | - | ||
| Sub bus 1 | Multiplex Tilt and Telescopic ECU | U0142 | - |
| Main Body ECU (Multiplex Network Body ECU)*1 | U1002 | โ | |
| U1115 | โ | ||
| CAN BUS WAVEFORMS |

CAN bus waveforms (Group 1)
![]() |
Normal waveform
![]() |
Open in both of the lines (CANH and CANL) of a CAN branch
![]() |
Short between the CAN bus lines (CANH and CANL)
CAN bus waveforms (reference) (Group 2)
![]() |
Open in a CAN branch line (CANH)
![]() |
Open in a CAN branch line (CANL)
![]() |
Open in a CAN main bus line (CANH)
![]() |
Short between a CAN bus line (CANH) and ground
![]() |
Short between a CAN bus line (CANL) and ground
| DATA SENDING/RECEIVING TABLE |
Data sending/receiving table
| Data content | Data Detected and Sent by | Data Received from (Can be Checked in Data List) | Data Received (Cannot be Checked in Data List) | Relevant Data List Item [Selected System] |
| Accelerator position | ECM (1AZ-FE/2AR-FE/2GR-FE) | Brake actuator assembly | Airbag sensor assembly |
|
| Engine speed | ECM (1AZ-FE/2AR-FE/2GR-FE) |
|
|
|
| Engine coolant temperature | ECM (1AZ-FE/2AR-FE/2GR-FE) |
| - |
|
| Vehicle speed | Brake actuator assembly |
| Airbag sensor assembly |
|
| Combination meter assembly *3 |
|
|
| |
| Wheel speed | Brake actuator assembly | AFS ECU |
|
|
| Shift position | ECM (1AZ-FE/2AR-FE/2GR-FE) |
|
|
|
| Ambient temperature | Air conditioning amplifier assembly |
|
|
|
| FR door courtesy switch | Main body ECU (multiplex network body ECU) | - |
| FR Door Courtesy [Main Body] |
| Steering angle sensor | Steering sensor |
|
|
|
| Yaw rate sensor | Airbag sensor assembly | Brake actuator assembly |
| Yaw Rate Sensor [ABS/VSC/TRC] |
| Deceleration sensor | Airbag sensor assembly | Brake actuator assembly | ECM (1AZ-FE/2AR-FE/2GR-FE) |
|
| Headlight switch | Main body ECU (multiplex network body ECU) | AFS ECU | Combination meter assembly*2 |
|
| Combination meter assembly power source voltage*1 | Combination meter assembly | - | - | +B Voltage Value [Combination Meter] |
| Power steering ECU with motor assembly power source voltage*1 | Power steering ECU with motor assembly | - | - | IG Power Supply [EMPS] |
| Solar sensor*1 | Air conditioning amplifier assembly | - | - | Solar Sensor (D side) [Air Conditioner] |
| Ignition switch condition*1 | Smart key ECU assembly (certification ECU) | - | - | Ignition Switch [Entry & Start] |
| Clearance sonar main switch*1 | Clearance warning ECU assembly | - | - | Main Switch [Clearance Sonar] |
| ECM power source voltage*1 | ECM (1AZ-FE/2AR-FE/2GR-FE) | - | - |
|
| AFS off switch condition*1 | AFS ECU | - | - | AFS OFF Switch [AFS] |
| Tilt up switch condition*1 | Multiplex tilt and telescopic ECU | - | - | Tilt Up Switch [Tilt & Telescopic] |
| Navigation ECU sub-assembly power source voltage*1 | Navigation ECU sub-assembly | - | - | Battery Voltage [Navigation System] |
| Radio and display receiver assembly*1 | Radio and display receiver assembly | - | - | Battery Voltage [Navigation System] |
Details of relevant Data List items (Selected system: Engine and ECT) (for 1AZ-FE)
Warm up the engine.
Turn the A/C switch off.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed |
|
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 610 to 710 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Coolant Temp | Coolant temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | If 11 V or less, characteristics of some electrical components may change. |
| Accelerator Position | Accelerator pedal position/ Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%. |
| Neutral Position SW Signal | Park/Neutral position switch status/ ON or OFF | ON: Shift lever in P or N | - |
| Ambient Temp for A/C | Ambient temperature for A/C/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
Details of relevant Data List items (Selected system: Engine and ECT) (for 2AR-FE)
Warm up the engine.
Turn the A/C switch off.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed |
|
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 610 to 710 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Coolant Temp | Coolant temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | If 11 V or less, characteristics of some electrical components may change. |
| Accelerator Position | Accelerator pedal position/ Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%. |
| Neutral Position SW Signal | Park/neutral position switch status/ ON or OFF | ON: Shift lever in P or N | - |
| Ambient Temp for A/C | Ambient temperature for A/C/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
Details of relevant Data List items (Selected system: Engine) (for 2GR-FE)
Warm up the engine.
Turn the A/C switch off.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed |
|
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 600 to 700 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Coolant Temp | Coolant temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | If 11 V or less, characteristics of some electrical components may change. |
| Accelerator Position | Accelerator pedal position/ Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%. |
| Neutral Position SW Signal | Park/neutral position switch/ ON or OFF | ON: Shift lever in P or N | - |
| Ambient Temp for A/C | Ambient temperature for A/C/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
Details of relevant Data List items (Selected system: ABS/VSC/TRC)
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Deceleration Sensor | Acceleration sensor reading / Min.: -18.525 m/s2, Max.: 18.387 m/s2
| - | During deceleration/acceleration: Changes continuously |
| Deceleration Sensor2 | Acceleration sensor 2 reading / Min.: -18.525 m/s2, Max.: 18.387 m/s2
| - | During deceleration/acceleration: Changes continuously |
| Yaw Rate Sensor | Yaw rate sensor / Min.: -128 °/s, Max.: 127 °/s | Vehicle stopped: 0 °/s Turning right: -128 to 0 °/s Turning left: 0 to 127 °/s | - |
| Steering Angle Sensor | Steering angle sensor / Min.: -3276.8°, Max.: 3276.7° | Turning left: Increase Turning right: Decrease | - |
| FR Wheel Speed | Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Shift Lever Position | Shift lever position information / P,N, R, D/M, 1st-6th/B or Fail | Actual shift lever position | - |
| Vehicle Speed | Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Engine Revolutions | Engine speed / Min.: 0 rpm, Max.: 65535 rpm | Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 128.0% | When the accelerator pedal is released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
Details of relevant Data List items (Selected system: EMPS)
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / EMPS / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Meter Vehicle Velocity | Vehicle speed from meter/ Min.: 0.0 km/h (0.0mph) Max.: 300.0 km/h (186.4 mph) | 0 km/h (0 mph) | Engine running and vehicle stopped |
| No significant fluctuation | Engine running and vehicle driven at constant speed | ||
| Steering Angle Velocity | Steering angle speed/ Min.: -32768 deg/s Max.: 32767 deg/s | Value changes in proportion to steering speed - The value increases when turning left and decreases when turning right | Engine running and steering wheel being turned |
| IG Power Supply | IG power source voltage/ Min.: 0.0000 V Max.: 20.1531 V | 9 to 16 V | Ignition switch ON |
Details of relevant Data List items (Selected system: Navigation System)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Navigation System / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.:24 V | 11 to 14 V | - |
| Reverse Signal | Reverse Signal/ON or OFF | ON: Reverse selected OFF: Reverse not selected | - |
Details of relevant Data List items (Selected system: Clearance Sonar)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the clearance sonar main switch on.
Turn the intelligent tester on.
Enter the following menus: Body / Clearance Sonar / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Main Switch | Clearance sonar main switch/OFF or ON | OFF: Clearance sonar main switch off ON: Clearance sonar main switch on | - |
| Parking Signal | Parking signal/OFF or ON | OFF: Shift lever in any position other than P ON: Shift lever in P | - |
| Reverse Signal | Reverse signal/OFF or ON | OFF: Shift lever in any position other than R ON: Shift lever in R | - |
| Vehicle Speed Info | Vehicle speed signal/Snr Stop or Snr Work | Snr Stop: Vehicle speed approximately 13 km/h (8.1 mph) or more (when accelerating) or approximately 9 km/h (5.6 mph) or more (when decelerating) Snr Work: Vehicle speed less than approximately 13 km/h (8.1 mph) (when accelerating) or less than approximately 9 km/h (5.6 mph) (when decelerating) | - |
Details of relevant Data List items (Selected system: Entry & Start)
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry & Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | Engine switch ON / ON or OFF | ON: Engine switch ON OFF: Engine switch off |
|
Details of relevant Data List items (Selected system: Power Source Control)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift P Signal | Shift position P/ON or OFF | ON: Shift lever in P OFF: Shift lever not in P |
|
| Vehicle Speed Signal | Vehicle being driven or stopped/Stop or Run | Stop: Vehicle stopped Run: Vehicle being driven at 5 km/h (3 mph) or more | - |
Details of relevant Data List items (Selected system: Starting Control)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Staring Control / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Engine Speed | Engine speed/0 to 16383 r/min | Fluctuates in accordance with engine speed | - |
Details of relevant Data List items (Selected system: Combination Meter)
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed Meter | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
| Engine Rpm | Engine speed/Min.: 0 rpm, Max.: 12750 rpm |
| - |
| Coolant Temperature | Engine coolant temperature/-40 to 127.5°C (-40 to 261.5°F) | After warming up: 75 to 100°C (167 to 212°F) |
|
| +B Voltage Value | Battery voltage/Min.: 0 V, Max.: 25.5 V | 11 to 14 V | - |
| Ambient Temperature | Outside temperature/Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) | Almost the same as actual outside temperature | The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F) |
Details of relevant Data List items (Selected system: Air Conditioner)
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ambient Temp Sensor | Ambient temperature sensor (thermistor assembly) / Min.: -23.30°C (-9.94°F) Max.: 65.95°C (150.71°F) | Actual ambient temperature displayed | - |
| Solar Sensor (D side) | Driver side automatic light control sensor (solar sensor) / Min.: 0 Max.: 255 | Driver side automatic light control sensor (solar sensor) value increases as brightness increases | - |
| Engine Coolant Temp | Engine coolant temperature sensor / Min.: 1.30°C (34.34°F) Max.: 90.55°C (194.99°F) | Actual engine coolant temperature displayed | - |
Details of relevant Data List items (Selected system: Main Body ECU) (Multiplex Network Body ECU)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Door Courtesy | Front door courtesy light switch RH signal / ON or OFF | ON: Front door RH closed OFF: Front door RH open | - |
Details of relevant Data List items (Selected system: Tilt & Telescopic)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Tilt & Telescopic / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Freeze Speed Info | Vehicle speed data/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Stop → Drive → Stop | 0 km/h (0 mph) → Same speed as indicated on speedometer → 0 km/h (0 mph) |
Details of relevant Data List items (Selected system: AFS)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / AFS / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Headlight Low Beam State | Low beam headlight state/ON or OFF | ON: Low beam headlights on OFF: Low beam headlights off | - |
| Steering Sens Signal | Steering angle sensor signal value/-384.0 deg to 382.5 deg | Approx. 0 deg (When steering wheel is straight) | Value changes according to steering wheel position |
| FR Wheel Speed | Front right wheel speed/0.00 to 327.67 km/h (203.61 mph) | Condition can be displayed | - |
| FL Wheel Speed | Front left wheel speed/0.00 to 327.67 km/h (203.61 mph) | Condition can be displayed | - |
| Vehicle Speed | Vehicle speed/0.00 to 327.67 km/h (203.61 mph) | Condition can be displayed | - |