Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injector assemblies are located on the intake port. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A266398E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)


    A194105E84
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E30-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    E34-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    E32-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    E35-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    E33-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    E36-2 - Body ground
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)



NG
Go to step 4
OK


2.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E30-1 - E26-58 (#10)
    Always
    Below 1 Ω
    E34-1 - E26-54 (#20)
    Always
    Below 1 Ω
    E32-1 - E26-57 (#30)
    Always
    Below 1 Ω
    E35-1 - E26-53 (#40)
    Always
    Below 1 Ω
    E33-1 - E26-56 (#50)
    Always
    Below 1 Ω
    E36-1 - E26-55 (#60)
    Always
    Below 1 Ω
    E30-1 or E26-58 (#10) - Body ground
    Always
    10 kΩ or higher
    E34-1 or E26-54 (#20) - Body ground
    Always
    10 kΩ or higher
    E32-1 or E26-57 (#30) - Body ground
    Always
    10 kΩ or higher
    E35-1 or E26-53 (#40) - Body ground
    Always
    10 kΩ or higher
    E33-1 or E26-56 (#50) - Body ground
    Always
    10 kΩ or higher
    E36-1 or E26-55 (#60) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)
  1. Disconnect the fuel injector assembly connectors.

  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1A-3 - E30-2
    Always
    Below 1 Ω
    1A-3 - E34-2
    Always
    Below 1 Ω
    1A-3 - E32-2
    Always
    Below 1 Ω
    1A-3 - E35-2
    Always
    Below 1 Ω
    1A-3 - E33-2
    Always
    Below 1 Ω
    1A-3 - E36-2
    Always
    Below 1 Ω
    1A-3 or E30-2 - Body ground
    Always
    10 kΩ or higher
    1A-3 or E34-2 - Body ground
    Always
    10 kΩ or higher
    1A-3 or E32-2 - Body ground
    Always
    10 kΩ or higher
    1A-3 or E35-2 - Body ground
    Always
    10 kΩ or higher
    1A-3 or E33-2 - Body ground
    Always
    10 kΩ or higher
    1A-3 or E36-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
  1. Inspect the No. 1 integration relay (IG2 relay) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (IG2 RELAY) (Click here)
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)