Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B288548
  1. Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.



4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    B288549
  1. Disengage the 3 clips and remove the front door lower frame bracket garnish.



5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B281681
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

  1. Disconnect each connector and remove the multiplex network master switch assembly with front door armrest base panel.



6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B281683
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

  1. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.



7. REMOVE FRONT ARMREST ASSEMBLY


    B277187
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.



8. REMOVE COURTESY LIGHT ASSEMBLY


    E226714E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side
    *1
    Protective Tape

  1. Disconnect the connector and remove the courtesy light assembly.



9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B288550E01
  1. Put protective tape around the front door panel.
    Text in Illustration 
    *1
    Protective Tape



    B288551
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 10 clips.



    B288552E01
  1. Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss
    *2
    Front Door Inner Glass Weatherstrip

  1. Disengage the reference boss from the front door panel.

  1. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

  1. Disconnect the connector.



    B277192
  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.



10. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B277194
  1. Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly.



11. REMOVE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY


    E227550
  1. Disengage the 3 clamps and claw, and remove the front door inside handle illumination light assembly.



12. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    B277195E01
  1. Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



13. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    E226775
  1. Disconnect the connector.

  1. Remove the 4 screws.



    E226773
  1. Disengage the 2 claws and remove the front No. 1 speaker assembly.

    NOTICE:
    Do not touch the speaker cone.



14. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


    B280609
  1. Disconnect the connector.

  1. Remove the 3 bolts.

  1. Disengage the claw and remove the outer rear view mirror assembly.



15. REMOVE FRONT DOOR SERVICE HOLE COVER


    B281686
  1. Disconnect each connector.

  1. Disengage the 4 clamps.

  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



16. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B281733
  1. Remove the grommet.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network master switch assembly.



    B288542
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.



    B288543E01
  1. Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.



17. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    B281734E01
  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

  1. Remove the 5 bolts.

  1. Remove the front door window regulator assembly.

  1. Remove the temporary bolt from the front door window regulator assembly.



18. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B280344
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.



19. REMOVE NO. 2 FRONT DOOR STIFFENER CUSHION


    B281687E01
  1. Remove the 2 bolts.
    Text in Illustration 
    *1
    Double-sided Tape

  1. Disengage the 2 guides and remove the No. 2 front door stiffener cushion.



20. REMOVE FRONT DOOR GLASS RUN


    B281735
  1. Remove the front door glass run.



21. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    B280347
  1. Remove the 2 bolts.

  1. Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.



22. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B288544
  1. Remove the 2 bolts.

  1. Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.



23. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    B280351
  1. Remove the hole plug.



    B280352
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    B280353
  1. Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.



25. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    B280630
  1. Remove the hole plug.



    B280355
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



26. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


  1. w/ Smart Entry and Start System:



      B280356
    1. Disengage the 2 claws.

    2. Using a screwdriver, disconnect the connector.



    B280357
  1. Remove the front door outside handle assembly as shown in the illustration.



27. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD


    B280359
  1. Disengage the 3 claws and remove the front door front outside handle pad.



28. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD


    B280360
  1. Disengage the 2 claws and remove the front door rear outside handle pad.



29. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY


    B280361E01
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

  1. Slide the front door lock with motor assembly downward, and remove the front door lock with motor assembly and cables as a unit.



  1. When reusing the front door lock with motor assembly:



      B280363
    1. Remove the door lock wiring harness seal from the front door lock with motor assembly.



30. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B280364
  1. Remove the front door lock remote control cable assembly.



31. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280366
  1. Using a screwdriver, disengage the 3 claws.



    B280367
  1. Remove the front door inside locking cable assembly.



32. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


  1. w/ Smart Entry and Start System System:



      B280369
    1. Disconnect the connector.

    2. Disengage the 3 clamps.



    B280370E01
  1. Using a T30 "TORX" socket wrench, remove the screw and door handle nut.
    Text in Illustration 
    *1
    Door Handle Nut
    *a
    Outside
    *b
    Inside

  1. Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it.



33. REMOVE FRONT DOOR WIRE (w/ Smart Entry and Start System)


    B280372
  1. Disengage the 3 clamps and remove the front door wire.



34. REMOVE FRONT DOOR LOCK OPEN ROD


    B280374E01
  1. Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.



35. REMOVE FRONT DOOR CHECK ASSEMBLY


    B280375
  1. Remove the 3 bolts and front door check assembly.



36. REMOVE FRONT DOOR WEATHERSTRIP


    B281736
  1. Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.



37. REMOVE DOOR FRAME GARNISH


    B277197
  1. Disengage the clip and remove the door frame garnish.

    HINT:
    This garnish needs to be replaced with a new one because the clip will break when removing it.



38. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP


    B281737
  1. Using a clip remover, disengage the 8 clips and remove the front door No. 2 weatherstrip.



39. REMOVE FRONT DOOR PANEL CUSHION


    B281738
  1. Disengage the 2 claws and remove the 2 front door panel cushions.



40. REMOVE FRONT DOOR VENT SEAL


    B280379
  1. Remove the front door vent seal.



41. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY


    B280066E01
  1. Put protective tape around the front door belt moulding assembly.
    Text in Illustration 
    *1
    Protective Tape



    B280067E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the front door belt moulding assembly.
    Text in Illustration 
    *1
    Protective Tape



42. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:
When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or moulding excessively.

  1. Using a heat light, heat the front door rear window frame moulding.



    B280095E01
  1. Using a moulding remover, disengage the clip and remove the front door rear window frame moulding.
    Text in Illustration 
    *1
    Double-sided Tape
    *2
    Caulking Sponge



43. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
  1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.



    B280100E01
  1. Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
    Area
    Dimension
    A
    5.0 mm

    NOTICE:
    Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 7 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Prying the rivets with the drill may damage the rivet installation holes or drill bit.
    3. Be careful of the drilled rivets, as they may be hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Disengage the claw and guide, and remove the front door upper window frame moulding from the door frame.



44. REMOVE FRONT DOOR STRIPE
  1. Using a heat light, heat the front door stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Front Door Outside Stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B280089
  1. Pull back on one of the ends of the front door stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



45. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE
  1. Using a heat light, heat the front door lower outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Front Door Rear Outside Stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B280090
  1. Pull back on one of the ends of the front door lower outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.