Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR

REAR DOOR > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B280387
  1. Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.



4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B280389
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



5. REMOVE REAR ARMREST ASSEMBLY


    B280391
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B280590E01
  1. Put protective tape around the rear door panel.
    Text in Illustration 
    *1
    Protective Tape



    B280393
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 8 clips.



    B280394E01
  1. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss
    *2
    Rear Door Inner Glass Weatherstrip

  1. Disengage the reference boss from the rear door panel.

  1. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    B280396
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

  1. Disconnect the connector.



    B280399E01
  1. Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



7. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B277194
  1. Disengage the 2 claws and guide, and remove the rear door inside handle sub-assembly.



8. REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY


    E227551
  1. Disengage the 3 clamps and claw, and remove the rear door inside handle illumination light assembly.



9. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B280398E01
  1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



10. REMOVE REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)


    B281730
  1. Remove the 9 screws and rear curtain sub-assembly.



11. REMOVE REAR DOOR SERVICE HOLE COVER


    B281690
  1. Disconnect the connector and remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



12. REMOVE REAR DOOR CHECK ASSEMBLY


    B280406
  1. Remove the bolt and 2 nuts and rear door check assembly.



13. REMOVE REAR DOOR WEATHERSTRIP


    B281691
  1. Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.



14. REMOVE REAR DOOR GLASS RUN


    B280408
  1. Remove the rear door glass run.



15. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B280409
  1. Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

    NOTICE:
    When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.



16. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B280410
  1. Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.



17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B281692
  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



18. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY


    B280414E01
  1. Using a screwdriver, remove the rear door glass channel sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



19. REMOVE REAR DOOR GLASS CHANNEL FILLER
  1. Remove the rear door glass channel filler.



20. REMOVE REAR DOOR FRAME GARNISH


    B280403
  1. Disengage the clip and remove the rear door frame garnish.

    HINT:
    This garnish needs to be replaced with a new one because the clip will break when removing it.



21. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY


    B280418E01
  1. Disconnect the connector.

  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator assembly.

  1. Remove the temporary bolt from the rear door window regulator assembly.



22. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B280419
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and rear power window regulator motor assembly.



23. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY


    B280420E01
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.
    Text in Illustration 
    *1
    Release Plate

  1. Move the rear door lock with motor assembly downward and pull the release plate out of the rear door outside handle frame.



  1. When reusing the rear door lock with motor assembly:



      B280422
    1. Remove the door lock wiring harness seal from the rear door lock with motor assembly.



24. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B280423
  1. Using a screwdriver, disengage the claw.



    B280425
  1. Remove the rear door lock remote control cable assembly.



25. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280427
  1. Using a screwdriver, disengage the 3 claws.



    B280429
  1. Remove the rear door inside locking cable assembly.



26. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    B280431
  1. Using a T30 "TORX" socket wrench, loosen the screw.

    HINT:
    The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

  1. Disengage the claw and remove the rear door outside handle cover.



27. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    B280432
  1. Pull and hold the release plate of the rear door outside handle frame sub-assembly as shown in the illustration.

    NOTICE:
    The release plate may interfere with the rear door outside handle assembly and may be damaged when removing the rear door outside handle assembly, unless the release plate of the rear door outside handle frame sub-assembly is pulled and held.



    B280433
  1. Remove the rear door outside handle assembly as shown in the illustration.



28. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    B280435
  1. Disengage the 3 claws and remove the rear door front outside handle pad.



29. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    B280436
  1. Disengage the 2 claws and remove the rear door rear outside handle pad.



30. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B280437E01
  1. Using a T30 "TORX" socket wrench, remove the screw and door handle nut.
    Text in Illustration 
    *1
    Door Handle Nut
    *a
    Outside
    *b
    Inside

  1. Slide the rear door outside handle frame sub-assembly to disengage the claw of the rear door outside handle frame sub-assembly, and then remove it.



31. REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)


    B281726E01
  1. Using a screwdriver, push out the pin as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B281727E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the pin.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B281728
  1. Disengage the 2 claws and remove the 2 curtain hooks as shown in the illustration.



32. REMOVE REAR DOOR NO. 2 WEATHERSTRIP


    B281741
  1. Using a clip remover, disengage the 5 clips and remove the rear door No. 2 weatherstrip.



33. REMOVE REAR DOOR PANEL CUSHION


    B281693
  1. Disengage the 2 claws and remove the 2 rear door panel cushions.



34. REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    B280063E01
  1. Put protective tape around the rear door belt moulding assembly.
    Text in Illustration 
    *1
    Protective Tape



    B280064E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws to remove the rear door belt moulding assembly as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



35. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:
When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or moulding excessively.

  1. Using a heat light, heat the rear door front window frame moulding.



    B280093E01
  1. Using a moulding remover, disengage the clip and remove the rear door front window frame moulding.
    Text in Illustration 
    *1
    Double-sided Tape
    *2
    Caulking Sponge



36. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING
  1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.



    B280098E01
  1. Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
    Area
    Dimension
    A
    5.0 mm

    NOTICE:
    Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Prying the rivets with the drill may damage the rivet installation holes or drill bit.
    3. Be careful of the drilled rivets, as they may be hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Disengage the guide and remove the rear door upper window frame moulding from the door frame.



37. REMOVE REAR DOOR OUTSIDE STRIPE
  1. Using a heat light, heat the rear door outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Rear Door Outside Stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B280091
  1. Pull back on one of the ends of the rear door outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



38. REMOVE REAR DOOR LOWER OUTSIDE STRIPE
  1. Using a heat light, heat the rear door lower outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Rear Door Lower Outside stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B280092
  1. Pull back on one of the ends of the rear door lower outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.