Home › Vehicle Exterior › LIGHTING (EXT) › AFS (ADAPTIVE FRONT-LIGHTING SYSTEM)

DTC    B2417    Headlight Beam Level Control Motor LH Malfunction

DTC    B2418    Headlight Beam Level Control Motor RH Malfunction

for Preparation Click here


DESCRIPTION

The headlight leveling motor receives operation signals from the AFS ECU (headlight swivel ECU assembly). The AFS ECU (headlight swivel ECU assembly) receives signals indicating the operating conditions of the headlight leveling motor.

DTC No.
DTC Detection Condition
Trouble Area
B2417
  1. Malfunction in headlight leveling motor LH
  2. Open or short in headlight leveling motor LH circuit
  1. Headlight leveling motor LH
  2. Harness or connector
  3. AFS ECU (headlight swivel ECU assembly)
B2418
  1. Malfunction in headlight leveling motor RH
  2. Open or short in headlight leveling motor RH circuit
  1. Headlight leveling motor RH
  2. Harness or connector
  3. AFS ECU (headlight swivel ECU assembly)

WIRING DIAGRAM


E220285E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2417 or B2418 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / AFS / Active Test.

  1. Check that the leveling motors operate.

    AFS 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Drive The Leveling Motor UP
    Leveling motor upward operation
    ON/OFF
    ON: Moves up
    OFF: Stops
    Drive The Leveling Motor DOWN
    Leveling motor downward operation
    ON/OFF
    ON: Moves down
    OFF: Stops

    OK:
    Headlight leveling motors operate normally.



NG
Go to step 4
OK


3.CHECK HEADLIGHT LEVELING MOTOR
  1. Replace the headlight leveling motor with a new or a known good one (Click here).

  1. Check for DTCs (Click here).

    HINT:
    DTC B2417 or B2418 is stored when the AFS ECU (headlight swivel ECU assembly) receives a signal indicating an abnormality from a headlight leveling motor. It is not possible to judge whether a headlight leveling motor is normal using an Active Test, because even if the motor operates normally during the Active Test, it may still output a signal indicating an abnormality.

    OK:
    DTC B2417 or B2418 is not output.



NG
REPLACE AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY) (Click here)
OK

END (HEADLIGHT LEVELING MOTOR WAS DEFECTIVE) 

4.CHECK HARNESS AND CONNECTOR (BATTERY - AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY))


    E166980E41
  1. Disconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A35-15 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to AFS ECU (Headlight Swivel ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY) - BODY GROUND)


    E166980E40
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A35-22 (E1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to AFS ECU (Headlight Swivel ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY) - HEADLIGHT LEVELING MOTOR)
  1. Disconnect the LH side or RH side headlight leveling motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side (B2417) 
    Tester Connection
    Condition
    Specified Condition
    A35-3 (LH+) - A19-1 (LHB1)
    Always
    Below 1 Ω
    A35-27 (LH-) - A19-3 (LHE)
    Always
    Below 1 Ω
    A35-30 (LHE) - A19-2 (LHM+)
    Always
    Below 1 Ω
    A35-3 (LH+) - Body ground
    Always
    10 kΩ or higher
    A35-27 (LH-) - Body ground
    Always
    10 kΩ or higher
    A35-30 (LHE) - Body ground
    Always
    10 kΩ or higher
    RH Side (B2418) 
    Tester Connection
    Condition
    Specified Condition
    A35-4 (RH+) - A61-1 (RHB1)
    Always
    Below 1 Ω
    A35-28 (RH-) - A61-3 (RHE)
    Always
    Below 1 Ω
    A35-11 (RHE) - A61-2 (RHM+)
    Always
    Below 1 Ω
    A35-4 (RH+) - Body ground
    Always
    10 kΩ or higher
    A35-28 (RH-) - Body ground
    Always
    10 kΩ or higher
    A35-11 (RHE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY)


    E166987E11
  1. Reconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    LH Side (B2417) 
    Tester Connection
    Condition
    Specified Condition
    A35-3 (LH+) - A35-27 (LH-)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    RH Side (B2418) 
    Tester Connection
    Condition
    Specified Condition
    A35-4 (RH+) - A35-28 (RH-)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (AFS ECU (Headlight Swivel ECU Assembly))



NG
REPLACE AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY) (Click here)
OK


8.CHECK HEADLIGHT LEVELING MOTOR
  1. Replace the headlight leveling motor with a new or a known good one (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2417 or B2418 is not output.



NG
REPLACE AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY) (Click here)
OK

END (HEADLIGHT LEVELING MOTOR WAS DEFECTIVE)