Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

  1. If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.
  3. If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E226522E04


E226483E03


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the stereo component amplifier assembly and speakers.

  1. Measure the resistance between each of the front No. 1 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - J5-1
    Always
    Below 1 Ω
    I68-30 (FR-) - J5-2
    Always
    Below 1 Ω
    I68-11 (FL+) - K5-1
    Always
    Below 1 Ω
    I68-26 (FL-) - K5-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-12 (TWR+) - I84-4
    Always
    Below 1 Ω
    I68-27 (TWR-) - I84-3
    Always
    Below 1 Ω
    I68-14 (TWL+) - I2-4
    Always
    Below 1 Ω
    I68-29 (TWL-) - I2-3
    Always
    Below 1 Ω

  1. Measure the resistance between the front No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-13 (CTR+) - I60-2
    Always
    Below 1 Ω
    I68-28 (CTR-) - I60-1
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-10 (SR+) - O19-2
    Always
    Below 1 Ω
    I68-25 (SR-) - O19-1
    Always
    Below 1 Ω
    I68-9 (SL+) - O20-2
    Always
    Below 1 Ω
    I68-24 (SL-) - O20-1
    Always
    Below 1 Ω

  1. Measure the resistance between the rear speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-8 (WF1+) - O22-1
    Always
    Below 1 Ω
    I68-23 (WF1-) - O22-2
    Always
    Below 1 Ω

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - Body ground
    Always
    10 kΩ or higher
    I68-30 (FR-) - Body ground
    Always
    10 kΩ or higher
    I68-11 (FL+) - Body ground
    Always
    10 kΩ or higher
    I68-26 (FL-) - Body ground
    Always
    10 kΩ or higher
    I68-12 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I68-27 (TWR-) - Body ground
    Always
    10 kΩ or higher
    I68-14 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I68-29 (TWL-) - Body ground
    Always
    10 kΩ or higher
    I68-13 (CTR+) - Body ground
    Always
    10 kΩ or higher
    I68-28 (CTR-) - Body ground
    Always
    10 kΩ or higher
    I68-10 (SR+) - Body ground
    Always
    10 kΩ or higher
    I68-25 (SR-) - Body ground
    Always
    10 kΩ or higher
    I68-9 (SL+) - Body ground
    Always
    10 kΩ or higher
    I68-24 (SL-) - Body ground
    Always
    10 kΩ or higher
    I68-8 (WF1+) - Body ground
    Always
    10 kΩ or higher
    I68-23 (WF1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E219303E15
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J5-1 - J5-2
      Always
      4.6 to 6.6 Ω
      K5-1 - K5-2
      Always
      4.6 to 6.6 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E219304E15
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I84-4 - I84-3
      Always
      3.4 to 5.2 Ω
      I2-4 - I2-3
      Always
      3.4 to 5.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    E222247E10
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I60-1 - I60-2
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front No. 3 Speaker Assembly)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E222247E11
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O19-1 - O19-2
      Always
      6.8 to 10.2 Ω
      O20-1 - O20-2
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear No. 2 Speaker Assembly)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


6.INSPECT REAR SPEAKER ASSEMBLY


    E219303E16
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O22-1 - O22-2
      Always
      4.8 to 6.8 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)