Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Rear Fog Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog lights via the engine room junction block assembly.

WIRING DIAGRAM


E220286E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK OPERATION (TAILLIGHTS)
  1. Check the operation of the taillights.

    OK:
    Taillights operate normally.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Check that the relay operates.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Fog Light Relay
    Rear fog light relay
    ON/OFF
    Light control switch is in tail position

    OK:
    Rear fog light relay operates. (Rear fog lights come on.)



NG
Go to step 3
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 

3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Using a voltmeter, check the signal reading of the engine room junction block assembly (Click here).

    OK:
    Output signal reading is normal.



NG
INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)


  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.


    E230000E04

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A-1 (BATT) - Body ground
    Always
    11 to 14 V
    B-1 (ALT) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1F-3 (GND1) - Body ground
    Always
    Below 1 Ω
    1G-4 (GND2) - Body ground
    Always
    Below 1 Ω


Text in Illustration 
*a
Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
-
-


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1G-2 (TAIL) - 3D-9
    Always
    Below 1 Ω
    3D-9 - Body ground
    Always
    10 kΩ or higher
    1F-10 (RFGS) - 3D-35
    Always
    Below 1 Ω
    3D-35 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).



    E182509E09
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    MB-27 (RFGO) - 3D-35
    Always
    Below 1 Ω
    3D-35 - Body ground
    Always
    10 kΩ or higher

  1. Connect a positive (+) lead from the battery to terminal 3E-1.

  1. Connect a negative (-) lead from the battery to terminal MB-14.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3D-9 - Battery negative
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - REAR LIGHT ASSEMBLY)
  1. Disconnect the 1F engine room junction block assembly connectors.

  1. Disconnect the T1 and T7 rear light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1F-12 - T7-4
    Always
    Below 1 Ω
    1F-12 - T1-4
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T7-3 - Body ground
    Always
    Below 1 Ω
    T1-3 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Replace the engine room junction block assembly with a new or a known good one (Click here).

  1. Check that the fog lights operate normally.

    OK:
    The fog lights operate normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (ENGINE ROOM JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)