Home › Brake › BRAKE (REAR) › REAR BRAKE

REAR BRAKE > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. INSTALL REAR DISC


    C238505E01
  1. Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



2. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Install the parking brake shoe adjusting hole plug.



3. INSTALL DISC BRAKE CYLINDER MOUNTING


    C243125
  1. Install the disc brake cylinder mounting with the 2 bolts.

    Torque:
    62 N*m{ 630 kgf*cm , 46 ft.*lbf }



4. INSTALL REAR DISC BRAKE BUSHING DUST BOOT


    C239548
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



    C243124
  1. Install the 2 rear disc brake bushing dust boots to the disc brake cylinder mounting.



5. INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSHING


    C211757
  1. Apply a light layer of lithium soap base glycol grease to the contact surface of the rear disc brake cylinder slide pin.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease

  1. Install a new rear disc brake cylinder slide bushing to the rear disc brake cylinder slide pin.



6. INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN (for Lower Side)


    C211758
  1. Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the rear disc brake cylinder slide pin.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease



    C243123
  1. Install the rear disc brake cylinder slide pin to the disc brake cylinder mounting.

  1. Push the rear disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.



7. INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN (for Upper Side)


    C211759
  1. Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the rear disc brake cylinder slide pin.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease



    C243122
  1. Install the rear disc brake cylinder slide pin to the disc brake cylinder mounting.

  1. Push the rear disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.



8. INSTALL REAR DISC BRAKE PAD SUPPORT PLATE


    C273541E01
  1. Install the 2 rear disc brake pad support plates to the disc brake cylinder mounting.
    Text in Illustration 
    *1
    Rear Disc Brake Pad Support Plate
    *2
    Disc Brake Cylinder Mounting

    NOTICE:
    Firmly push to install the rear disc brake pad support plate and disc brake cylinder mounting against each other so that there is no clearance between the surfaces A and a, and B and b.



9. INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT


    C239557
  1. Install the pad wear indicator plate to each rear disc brake pad.

    NOTICE:
    Install each pad wear indicator plate in the correct position and direction.



    C239556
  1. Apply disc brake grease to the inside of the rear disc brake anti-squeal shims.
    Text in Illustration 
    V100155
    Disc Brake Grease



    C239558
  1. Install the rear disc brake anti-squeal shim to each rear disc brake pad with pad wear indicator plate.

    NOTICE:
    1. Disc brake grease may seep out slightly from the areas where the rear disc brake anti-squeal shims are installed.
    2. Make sure that disc brake grease is not applied onto the lining surface.



10. INSTALL REAR DISC BRAKE PAD
  1. Install the 2 rear disc brake pads with rear disc brake anti-squeal shim kit to the disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.



11. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY


    C239570E01
  1. Hold the rear disc brake cylinder slide pin, and install the rear disc brake cylinder assembly to the disc brake cylinder mounting with the 2 bolts.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }



12. CONNECT REAR FLEXIBLE HOSE


    C243121E01
  1. Connect the rear flexible hose to the rear disc brake cylinder assembly with the union bolt and a new gasket.
    Text in Illustration 
    *a
    Lock Hole

    Torque:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }

    NOTICE:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



13. BLEED BRAKE LINE
(Click here)


14. ADJUST PARKING BRAKE
(Click here)


15. INSTALL REAR WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }