FUEL TANK > REMOVAL |
| 1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY |
| 2. DRAIN FUEL |
| 3. REMOVE CENTER EXHAUST PIPE ASSEMBLY |
| 4. REMOVE NO. 1 FLOOR UNDER COVER |
![]() |
Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.
![]() | Nut (attached to under cover) |
| 5. REMOVE NO. 2 FLOOR UNDER COVER |
![]() |
Remove the 2 clips.
![]() | Nut (attached to under cover) |
Disengage the 6 nuts and remove the No. 2 floor under cover.
| 6. DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Remove the bolt and nut of the No. 2 parking brake cable assembly.
| 7. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Remove the bolt and nut of the No. 3 parking brake cable assembly.
| 8. REMOVE REAR NO. 1 STABILIZER BAR BRACKET |
![]() |
Remove the 4 bolts and 2 rear No. 1 stabilizer bar brackets.
| 9. REMOVE LOWER CENTER FUEL TANK PROTECTOR |
![]() |
Remove the 4 bolts and lower center fuel tank protector.
| 10. DISCONNECT FUEL PUMP TUBE SUB-ASSEMBLY |
![]() |
Pinch the fuel tube connector and then pull out the fuel pump tube sub-assembly.
| *1 | Retainer |
| *2 | Fuel Pipe |
| *3 | Fuel Tube Connector |
| *4 | O-ring |
| *5 | Fuel Pump Tube |
![]() | Pinch |
![]() | Pull Out |
| 11. REMOVE FUEL TANK ASSEMBLY |
![]() |
Loosen the clip, then disconnect the fuel emission hose from the charcoal canister.
![]() |
Support the fuel tank assembly using an engine lifter.
![]() |
Remove the 2 bolts of the fuel tank bands.
Slightly lower the engine lifter.
![]() |
Loosen the hose clamp bolt and disconnect the fuel tank to filler pipe hose.
![]() |
Loosen the hose clamp bolt and disconnect the breather tube fuel hose.
Lower the engine lifter to remove the fuel tank assembly.
![]() |
Remove the 2 pins and 2 fuel tank bands as shown in the illustration.
![]() |
Remove the 4 clip nuts.
| 12. REMOVE NO. 1 FUEL TANK CUSHION |
![]() |
Remove the No. 1 fuel tank cushion.
| *1 | No. 1 Fuel Tank Cushion |
| *2 | No. 2 Fuel Tank Cushion |
| 13. REMOVE NO. 2 FUEL TANK CUSHION |
Remove the 7 No. 2 fuel tank cushions.
| 14. REMOVE NO. 2 FUEL TANK PROTECTOR |
![]() |
Disengage the 2 claws, and remove the No. 2 fuel tank protector by sliding it as shown in the illustration.
| 15. REMOVE NO. 3 FUEL TANK PROTECTOR |
![]() |
Disengage the 2 claws, and remove the No. 3 fuel tank protector by sliding it as shown in the illustration.
| 16. REMOVE FUEL CUT OFF WITH TUBE VALVE ASSEMBLY |
![]() |
Insert a clip remover between the fuel cut off with tube valve assembly and the fuel tank breather tube gasket, and remove the fuel cut off with tube valve assembly by gradually pushing it upward.
| *1 | Fuel Cut Off With Tube Valve Assembly |
| *2 | Fuel Tank Breather Tube Gasket |
Separate the 2 No. 4 fuel tube clamps.
Remove the 2 fuel tank breather tube gaskets.
| 17. REMOVE FUEL PUMP TUBE SUB-ASSEMBLY |
![]() |
Remove the fuel pump tube sub-assembly from the fuel main tube support and No. 4 fuel tube clamp.
| 18. REMOVE FUEL MAIN TUBE SUPPORT |
![]() |
Remove the bolt and fuel main tube support.
| 19. REMOVE NO. 4 FUEL TUBE CLAMP |
![]() |
Remove the 3 No. 4 fuel tube clamps.