VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
Release the parking brake.
When the ignition switch is turned to ON, check that the ABS warning, brake warning and slip indicator lights all come on for approximately 3 seconds.
| Trouble Area | See Procedure |
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| Brake warning light circuit (Remains on) |
Click here
|
| Brake warning light circuit (Does not come on) |
Click here
|
| Slip indicator light circuit (Remains on) |
Click here
|
| Slip indicator light circuit (Does not come on) |
Click here
|
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using the Intelligent Tester) |
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in P.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Switch the skid control ECU to Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
Check the ABS sensors.
Lost Booster Pressure Judgement Check
Turn the ignition switch to ON.
Check that the brake warning light comes on when depressing the brake pedal with a force of 59.0 N (6.0 kgf, 13.2 lbf) or more for 1 second or more. (The lost booster pressure state is judged to be normal.)
Start the engine while depressing the brake pedal with a force of 59.0 N (6.0 kgf, 13.2 lbf) or more for 1 second or more.
Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged to be normal.)
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.
Check that the ABS warning light goes off.
Stop the vehicle.
End of Sensor Check
If the sensor checks have completed, the ABS warning light blinks in the Test Mode pattern when the vehicle stops and the ABS warning light goes off while the vehicle is being driven.
Reading Sensor Check DTCs
Read the DTC(s) by following the intelligent tester screen.
Turn the ignition switch off and disconnect the intelligent tester.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
| C1271 | Low Output Signal of Front Speed Sensor RH |
|
| C1272 | Low Output Signal of Front Speed Sensor LH |
|
| C1273 | Low Output Signal of Rear Speed Sensor RH |
|
| C1274 | Low Output Signal of Rear Speed Sensor LH |
|
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH | Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH | Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
| C1281 | Master Cylinder Pressure Sensor Output Malfunction |
|
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When not Using the Intelligent Tester) |
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in P.
![]() |
Using SST, connect terminals TS and CG of the DLC3.
| *a | Front view of DLC3 |
Turn the ignition switch to ON.
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
Check the ABS sensors.
Lost Booster Pressure Judgement Check
Turn the ignition switch to ON.
Check that the brake warning light comes on when depressing the brake pedal with a force of 59.0 N (6.0 kgf, 13.2 lbf) or more for 1 second or more. (The lost booster pressure state is judged to be normal.)
Start the engine while depressing the brake pedal with a force of 59.0 N (6.0 kgf, 13.2 lbf) or more for 1 second or more.
Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged to be normal.)
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.
Check that the ABS warning light goes off.
Stop the vehicle.
End of Sensor Check
If the sensor checks have completed, the ABS warning light blinks in the Test Mode pattern when the vehicle stops and the ABS warning light goes off while the vehicle is being driven.
Reading Sensor Check DTCs
![]() |
Using SST, connect terminals TC and CG of the DLC3.
| *a | Front view of DLC3 |
Count the number of blinks of the ABS warning and slip indicator lights.
After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3, and turn the ignition switch off.
Turn the ignition switch to ON to cancel Test Mode.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
| 71 | Low Output Signal of Front Speed Sensor RH |
|
| 72 | Low Output Signal of Front Speed Sensor LH |
|
| 73 | Low Output Signal of Rear Speed Sensor RH |
|
| 74 | Low Output Signal of Rear Speed Sensor LH |
|
| 75 | Abnormal Change in Output Signal of Front Speed Sensor RH | Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| 76 | Abnormal Change in Output Signal of Front Speed Sensor LH | Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| 77 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| 78 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
| 81 | Master Cylinder Pressure Sensor Output Malfunction |
|