Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake warning light remains on:
  1. The skid control ECU connector is disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. EBD operation is not possible.
  5. The brake booster assembly is judged to be defective.

WIRING DIAGRAM


C243441E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V


    Result:

    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE)
    B
    NG (for 2AR-FE)
    C
    NG (for 1AZ-FE)
    D



B
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)

C
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)

D
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)
A


4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C238832E11
  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A49-25 (+BS) - Body ground
    Always
    11 to 14 V
    A49-25 (+BS) - A49-38 (GND1)
    Always
    11 to 14 V
    A49-28 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    A49-28 (IG1) - A49-38 (GND1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)


    C238832E12
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A49-38 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH ASSEMBLY)
  1. Reconnect the skid control ECU connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the intelligent tester, check the switch operation signal received when the parking brake is operated.

    OK:
    When the parking brake is operated, the display changes as shown above.



NG
Go to step 10
OK


7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH


    C230719E01
  1. Turn the ignition switch off.

  1. Remove the reservoir filler cap and the strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position changes according to the brake fluid level.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+) - 2 (E)
    Switch OFF (Float up)
    1.9 to 2.1 kΩ
    1 (+) - 2 (E)
    Switch ON (Float down)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly))

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.


    Result:

    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (Click here)

C
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (Click here)
A


8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)
  1. Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-19 (SW) - A30-1 (+)
    Always
    Below 1 Ω
    I18-19 (SW) - Body ground
    Always
    10 kΩ or higher
    A30-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT COMBINATION METER ASSEMBLY
  1. Reconnect the combination meter assembly connector and the brake fluid level warning switch connector.

  1. Perform an Active Test of the combination meter assembly (meter CPU) using the intelligent tester (Click here).

  1. Check the combination meter assembly.

    OK:
    The brake warning light turns on or off in accordance with the Active Test operation.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY


    C211519E03
  1. Turn the ignition switch off.

  1. Disconnect the parking brake switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+) - Body ground
    Parking brake switch ON
    (Switch pin free)
    Below 1 Ω
    1 (+) - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Parking Brake Switch Assembly)

    Result:

    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here)

C
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here)
A


11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH ASSEMBLY)
  1. Disconnect the main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3D-20 (PKB) - A42-1 (+)
    Always
    Below 1 Ω
    3D-20 (PKB) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)