Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Rear Door)

BLACK OUT TAPE (for Rear Door) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B280387
  1. Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.



4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B280389
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



5. REMOVE REAR ARMREST ASSEMBLY


    B280391
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B280590E01
  1. Put protective tape around the rear door panel.
    Text in Illustration 
    *1
    Protective Tape



    B280393
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 8 clips.



    B280394E01
  1. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss
    *2
    Rear Door Inner Glass Weatherstrip

  1. Disengage the reference boss from the rear door panel.

  1. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    B280396
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

  1. Disconnect the connector.



    B280399E01
  1. Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B280398E01
  1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



8. REMOVE REAR DOOR SERVICE HOLE COVER


    B281690
  1. Disconnect the connector and remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



9. REMOVE REAR DOOR CHECK ASSEMBLY


    B280406
  1. Remove the bolt and 2 nuts and rear door check assembly.



10. REMOVE REAR DOOR WEATHERSTRIP


    B281691
  1. Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.



11. REMOVE REAR DOOR GLASS RUN


    B280408
  1. Remove the rear door glass run.



12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B280409
  1. Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

    NOTICE:
    When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.



13. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B280410
  1. Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.



14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B281692
  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



15. REMOVE REAR DOOR FRAME GARNISH


    B280403
  1. Disengage the clip and remove the rear door frame garnish.

    HINT:
    This garnish needs to be replaced with a new one because the clip will break when removing it.



16. REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)


    B281726E01
  1. Using a screwdriver, push out the pin as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B281727E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the pin.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B281728
  1. Disengage the 2 claws and remove the 2 curtain hooks as shown in the illustration.



17. REMOVE REAR DOOR OUTSIDE STRIPE
  1. Using a heat light, heat the rear door outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Rear Door Outside Stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B280091
  1. Pull back on one of the ends of the rear door outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



18. REMOVE REAR DOOR LOWER OUTSIDE STRIPE
  1. Using a heat light, heat the rear door lower outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Rear Door Lower Outside stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B280092
  1. Pull back on one of the ends of the rear door lower outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.