Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING

REAR DOOR WINDOW FRAME MOULDING > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B280387
  1. Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.



4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B280389
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



5. REMOVE REAR ARMREST ASSEMBLY


    B280391
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B280590E01
  1. Put protective tape around the rear door panel.
    Text in Illustration 
    *1
    Protective Tape



    B280393
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 8 clips.



    B280394E01
  1. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss
    *2
    Rear Door Inner Glass Weatherstrip

  1. Disengage the reference boss from the rear door panel.

  1. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    B280396
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

  1. Disconnect the connector.



    B280399E01
  1. Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B280398E01
  1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



8. REMOVE REAR DOOR SERVICE HOLE COVER


    B281690
  1. Disconnect the connector and remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



9. REMOVE REAR DOOR CHECK ASSEMBLY


    B280406
  1. Remove the bolt and 2 nuts and rear door check assembly.



10. REMOVE REAR DOOR WEATHERSTRIP


    B281691
  1. Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.



11. REMOVE REAR DOOR GLASS RUN


    B280408
  1. Remove the rear door glass run.



12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B280409
  1. Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

    NOTICE:
    When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.



13. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B280410
  1. Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.



14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B281692
  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



15. REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    B280063E01
  1. Put protective tape around the rear door belt moulding assembly.
    Text in Illustration 
    *1
    Protective Tape



    B280064E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws to remove the rear door belt moulding assembly as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



16. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:
When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or moulding excessively.

  1. Using a heat light, heat the rear door front window frame moulding.



    B280093E01
  1. Using a moulding remover, disengage the clip and remove the rear door front window frame moulding.
    Text in Illustration 
    *1
    Double-sided Tape
    *2
    Caulking Sponge



17. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING
  1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.



    B280098E01
  1. Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
    Area
    Dimension
    A
    5.0 mm

    NOTICE:
    Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Prying the rivets with the drill may damage the rivet installation holes or drill bit.
    3. Be careful of the drilled rivets, as they may be hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Disengage the guide and remove the rear door upper window frame moulding from the door frame.