Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PANEL

AIR CONDITIONING PANEL > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Navigation System)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT PANEL GARNISH LH


    B280331
  1. Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.



4. REMOVE FRONT PANEL GARNISH RH


    B280332
  1. Disengage the 3 clips and 8 guides to remove the front panel garnish RH.



5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B281758
  1. Using a moulding remover, pry up on the center instrument cluster finish panel sub-assembly until there is enough of a gap to make it possible to pull on the panel by hand.



    B281757
  1. Pull the center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 7 clips and 2 guides to remove the center instrument cluster finish panel sub-assembly as shown in the illustration.



6. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    B281759
  1. Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 4 clips as shown in the illustration.

  1. Disconnect the connector to remove the No. 2 instrument panel register assembly.



7. REMOVE FRONT CONSOLE UPPER PANEL GARNISH


  1. for Blank Type:



      B284922
    1. Disengage the 2 claws and remove the front console upper panel garnish as shown in the illustration.



  1. for 3 Switch Hole Type:



      B281752
    1. Disengage the 2 claws as shown in the illustration.

    2. Disconnect the each connector to remove the front console upper panel garnish.



8. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)


    E227930E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    E227932
  1. Remove the 4 bolts.



    E227934
  1. Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.



9. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)


    E227929E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    E227931
  1. Remove the 4 bolts.



    E227933
  1. Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.



10. REMOVE NO. 1 RADIO BRACKET (w/o Navigation System)


    E227935
  1. Remove the 5 screws and No. 1 radio bracket.



11. REMOVE NO. 2 RADIO BRACKET (w/o Navigation System)


    E230758
  1. Remove the 5 screws and No. 2 radio bracket.



12. REMOVE NO. 1 RADIO RECEIVER BRACKET (w/ Navigation System)


    E227936
  1. Remove the 5 screws and No. 1 radio receiver bracket.



13. REMOVE NO. 2 RADIO RECEIVER BRACKET (w/ Navigation System)


    E230759
  1. Remove the 5 screws and No. 2 radio receiver bracket.



14. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E232140
  1. Disengage the 4 clips and guide, and remove the air conditioning control assembly as shown in the illustration.