Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION RECEIVER

NAVIGATION RECEIVER > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. A hard disk drive (HDD) is built into the navigation receiver assembly to store map and other data and is used for the navigation system. Therefore, make sure to read all of the precautions thoroughly before handling the navigation receiver assembly.
  3. When removing the hard disk drive, eliminate static electricity by touching the vehicle body to prevent components from being damaged.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT PANEL GARNISH LH


    B280331
  1. Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.



4. REMOVE FRONT PANEL GARNISH RH


    B280332
  1. Disengage the 3 clips and 8 guides to remove the front panel garnish RH.



5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B281758
  1. Using a moulding remover, pry up on the center instrument cluster finish panel sub-assembly until there is enough of a gap to make it possible to pull on the panel by hand.



    B281757
  1. Pull the center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 7 clips and 2 guides to remove the center instrument cluster finish panel sub-assembly as shown in the illustration.



6. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    B281759
  1. Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 4 clips as shown in the illustration.

  1. Disconnect the connector to remove the No. 2 instrument panel register assembly.



7. REMOVE FRONT CONSOLE UPPER PANEL GARNISH


  1. for Blank Type:



      B284922
    1. Disengage the 2 claws and remove the front console upper panel garnish as shown in the illustration.



  1. for 3 Switch Hole Type:



      B281752
    1. Disengage the 2 claws as shown in the illustration.

    2. Disconnect the each connector to remove the front console upper panel garnish.



8. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY


    E227929E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    E227931
  1. Remove the 4 bolts.



    E227933
  1. Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.



9. REMOVE NO. 1 RADIO RECEIVER BRACKET


    E227936
  1. Remove the 5 screws and No. 1 radio receiver bracket.



10. REMOVE NO. 2 RADIO RECEIVER BRACKET


    E230759
  1. Remove the 5 screws and No. 2 radio receiver bracket.



11. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E232140
  1. Disengage the 4 clips and guide, and remove the air conditioning control assembly as shown in the illustration.



12. REMOVE HARD DISK DRIVE


    E223753
  1. Remove the 2 screws.

  1. Disengage the 2 guides to remove the cover.



    E223754
  1. Pull out the hard disk drive from the navigation receiver assembly in the direction shown by the arrow in the illustration to remove it.



13. REMOVE NAVIGATION ECU SUB-ASSEMBLY