Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System) > Only Wireless Control Function is Inoperative

for Preparation Click here


DESCRIPTION

The door control receiver receives signals from the door control transmitter module sub-assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher relay signals to the combination meter assembly.

WIRING DIAGRAM


B290776E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure
  2. When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver and wireless function performance may be affected.

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.CHECK KEY REMINDER WARNING SYSTEM
  1. Check that the key reminder warning buzzer operates normally (Click here).

    OK:
    Key reminder warning buzzer operates normally.



NG
GO TO KEY REMINDER WARNING SYSTEM (Click here)
OK


3.CHECK DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY
  1. When a known good registered door control transmitter module sub-assembly is used, check that the wireless functions operate normally.

    Result:
    Result
    Proceed to
    Wireless door lock/unlock function operates normally with a known good door control transmitter module sub-assembly.
    A
    Wireless door lock/unlock function does not operate.
    B



B
Go to step 6
A


4.CHECK TRANSMITTER BATTERY
  1. Check the transmitter battery level of the door control transmitter module set sub-assembly that was checked first.

    1. Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

      Result:
      Result
      Proceed to
      Transmitter LED does not illuminate when switch is pressed and held
      A
      Transmitter LED illuminates 3 times or more when switch is pressed and held
      B
      Transmitter LED illuminates once or twice but not a third time
      C



B
REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

C
REPLACE TRANSMITTER BATTERY (Click here)
A


5.CHECK TRANSMITTER BATTERY (VOLTAGE)
  1. Inspect the battery capacity.

    1. Remove the battery from the door control transmitter module set sub-assembly that does not operate (Click here). Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative (-) terminal.

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.



    B178438
  1. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

    NOTICE:
    When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical key transmitter from being damaged.



    B281151
  1. Check the transmitter battery voltage.

    HINT:
    Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set sub-assembly.

    Standard Voltage:
    Item
    Content
    Tester Connection
    Transmitter battery positive (+) - Transmitter Battery negative (-)
    Condition
    Ignition switch off, all doors closed and lock or unlock switch is pressed
    Specified Condition
    2.2 to 3.2 V



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY 

6.CHECK WAVE ENVIRONMENT
  1. Bring the door control transmitter module sub-assembly near the door control receiver, and perform a wireless operation check.

    HINT:
    1. When the door control transmitter module sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Wireless functions operate normally.



NG
Go to step 7
OK

END (AFFECTED BY WAVE INTERFERENCE) 

7.SWITCH TO SELF-DIAGNOSTIC MODE
  1. Switch to self-diagnostic mode by operating the ignition key cylinder.

    1. Make sure that the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.

    2. Within 5 seconds after removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.

    3. Within 30 seconds after turning the ignition switch off, perform the following operation 9 times: turn the ignition switch to ON and then off.

      NOTICE:
      If the system cannot enter self-diagnostic mode, the system returns to normal mode.

      HINT:
      1. Turning the ignition switch to ON after the above operations have been completed ends self-diagnostic mode.
      2. Do not lock or unlock doors during self-diagnostic mode.



    B220865E09
  1. Check that the system has switched to self-diagnostic mode by checking the room light output pattern.



    B220865E08
  1. Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer output pattern*.
    *: w/ Wireless Door Lock Buzzer Answer Back Function


NEXT


8.CHECK SELF DIAGNOSTIC MODE

B163380E20

  1. Inspect the diagnostic outputs when the door control transmitter module sub-assembly switch is held down. The diagnostic outputs can be checked by the flash patterns of the interior lights and the buzzer patterns of the wireless door lock buzzer*.

    1. *: w/ Wireless Door Lock Buzzer Answer Back Function

    Result:
    Result
    Proceed to
    Normal wave (light flash pattern and buzzer pattern) is output.
    A
    Unmatching recognition code is output.
    B
    No diagnostic outputs.
    C



B
Go to step 9

C
Go to step 10
A

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY 

9.REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).

    OK:
    Recognition code can be registered.



NG
Go to step 14
OK

END (GO TO OPERATION CHECK) 

10.CHECK DOOR CONTROL RECEIVER (RESPONSE)
  1. Prepare the door control transmitter module sub-assembly from another vehicle.

  1. Press and hold down the door control transmitter module sub-assembly switch.

  1. Check that an unmatching recognition code is output.

    OK:
    Unmatching recognition code is output.



NG
Go to step 11
OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY 

11.CHECK DOOR CONTROL RECEIVER (+B, GND)


    B281165E02
  1. Disconnect the O24 door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O24-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O24-5 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Door Control Receiver)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK DOOR CONTROL RECEIVER (OUTPUT)
  1. Reconnect the O24 door control receiver connector.



    B281169E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O24-2 (RDA) - Body ground
    Ignition switch off, all doors closed and door control transmitter module sub-assembly switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and door control transmitter module sub-assembly switch pressed
    Pulse generation

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control Receiver)



B
REPLACE DOOR CONTROL RECEIVER (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER)
  1. Disconnect the I13 main body ECU (multiplex network body ECU) connector and the O24 door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I13-16 (RDA) - O24-2 (RDA)
    Always
    Below 1 Ω
    I13-16 (RDA) - Body ground
    Always
    10 kΩ or higher
    I13-4 (PRG) - O24-3 (PRG)
    Always
    Below 1 Ω
    I13-4 (PRG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE DOOR CONTROL RECEIVER
  1. Temporarily replace the door lock control receiver with a new or known good one (Click here).


NEXT


15.REGISTER RECOGNITION CODE
  1. Perform the Registration procedure (Click here).


NEXT


16.CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Check that the doors can be locked and unlocked by using the door control transmitter module sub-assembly lock and unlock switches.

    OK:
    Doors can be locked and unlocked using door control transmitter module sub-assembly.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)