Home › Brake › PARKING BRAKE › PARKING BRAKE PEDAL (for RHD)

PARKING BRAKE PEDAL (for RHD) > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing.

for Separate Type Yaw Rate Sensor: (Click here)
for Built-in Type Yaw Rate Sensor: (Click here)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD


4. REMOVE FRONT WHEEL RH


5. REMOVE SHIFT LEVER SUPPORT

HINT:
Use the same procedure as for the LH side (Click here).



6. REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (for Built-in Type Yaw Rate Sensor)
w/ Smart Entry and Start System:


7. REMOVE YAW RATE SENSOR (for Separate Type Yaw Rate Sensor)


    C247855
  1. Disconnect the connector from the yaw rate sensor.

  1. Remove the 2 nuts and yaw rate sensor.



8. REMOVE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (for Separate Type Yaw Rate Sensor)
w/ Smart Entry and Start System:


9. REMOVE YAW RATE SENSOR BRACKET (for Separate Type Yaw Rate Sensor)


    C247856
  1. Disengage the 2 clamps to separate the wire harnesses.

  1. Remove the 2 bolts and yaw rate sensor bracket.



10. REMOVE FLOOR CARPET BRACKET RH


    E227159
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket RH.



11. REMOVE AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Turn back the carpet.



    B278814
  1. Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 3 bolts and airbag sensor assembly.



12. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL


    B281782
  1. Disengage the 2 claws and 4 clips to remove the upper instrument panel finish panel as shown in the illustration.

  1. w/ Smart Entry and Start System:

    1. Disconnect the connector.



13. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

HINT:
Use the same procedure as for the LH side .



14. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
  1. for Manual Tilt and Manual Telescopic Steering Column:

    1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.



    B283374
  1. Using a moulding remover, disengage the 4 clips and 2 guides.



  1. for LHD:



      B280326
    1. Disengage the 3 claws, 7 clips and 4 guides.



  1. for RHD:



      B281784
    1. Disengage the 4 claws, 5 clips and 4 guides as shown in the illustration.

  1. Disconnect each connector.



    B280329
  1. Remove the instrument cluster finish panel assembly as shown in the illustration.



15. REMOVE COMBINATION METER ASSEMBLY

HINT:
Use the same procedure as for the LH side .



16. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY


    C239720
  1. Remove the bolt.

  1. Disengage the 2 claws to remove the No. 2 air duct sub-assembly.



17. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

HINT:
Use the same procedure as for the LH side .



18. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

HINT:
Use the same procedure as for the LH side .



19. LOOSEN ADJUSTING NUT


    C240121E01
  1. Remove the lock nut and loosen the adjusting nut.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Adjusting Nut



20. SEPARATE NO. 4 PARKING BRAKE CABLE ASSEMBLY


    C240122E01
  1. Separate the No. 4 parking brake cable assembly from the parking brake control pedal assembly as shown in the illustration.
    Text in Illustration 
    *a
    Turn
    *b
    Hold



21. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY


    C240126
  1. Remove the clip from the No. 1 parking brake cable assembly.

  1. Remove the bolt and separate the No. 1 parking brake cable assembly.



    C240127
  1. Disconnect the parking brake switch connector.



    C240128
  1. Remove the bolt, 2 nuts and parking brake control pedal assembly.