Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Separate Type Yaw Rate Sensor)

DTC    B1622/81    Lost communication with Side Airbag Sensor RH

DTC    B1623/81    Side Airbag Sensor Assembly RH Initialization Incomplete

DTC    B1632/81    Lost Communication with Rear Airbag Sensor RH

DTC    B1633/81    Rear Airbag Sensor Assembly RH Initialization Incomplete

DTC    B1642/81    Lost Communication with Side Satellite Sensor Bus RH

DTC    B1643/81    Side Satellite Sensor Bus RH Initialization Incomplete

for Preparation Click here


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH, rear seat airbag assembly RH, curtain shield airbag assembly RH and front seat outer belt assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
The side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected for the side collision sensor RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1622/81
B1623/81
B1632/81
B1633/81
B1642/81
B1643/81
  1. The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit.
  2. Side airbag sensor assembly RH malfunction
  3. Side No. 2 airbag sensor assembly RH malfunction
  4. Airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Side airbag sensor assembly RH
  3. Side No. 2 airbag sensor assembly RH
  4. Airbag sensor assembly

WIRING DIAGRAM


C239250E08


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1623 or B1643 is output.
    A
    Current DTC B1642 or 81 is output.
    B
    Current DTC B1632 or B1633 is output.
    C
    Current DTC B1622 is output.
    D
    Current DTCs B1622, B1623, B1632, B1633, B1642, B1643 and 81 are not output.
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.
    2. Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1643 and 81 may be output at this time, but they are not related to this check.



B
Go to step 3

C
Go to step 14

D
Go to step 21

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK HISTORY DTC
  1. Check for history DTCs (Click here).

    Result:
    Result
    Proceed to
    History DTC B1622 or B1632 is not output.
    A
    History DTC B1632 is output.
    B
    History DTC B1622 is output.
    C

    HINT:
    Codes other than history DTC B1622 and B1632 may be output at this time, but they are not related to this check.



B
Go to step 14

C
Go to step 21
A


3.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK NO. 2 FLOOR WIRE (OPEN)


    C238219E05
  1. Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - O11-3 (BBR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK NO. 2 FLOOR WIRE (SHORT)


    C238220E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - O11-3 (BBR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


6.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238220E02
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - Body ground
    Ignition switch ON
    Below 1 V
    O11-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


7.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238220E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    O11-3 (BBR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


8.CHECK NO. 2 FLOOR WIRE (OPEN)


    C240589E03
  1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - O11-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


9.CHECK NO. 2 FLOOR WIRE (SHORT)


    C238222E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - O11-2 (BCR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


10.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238222E03
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    O11-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


11.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238222E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    O11-2 (BCR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


12.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Connect the connectors to the side No. 2 airbag sensor assembly RH and airbag sensor assembly.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623, B1642, B1643 or 81 is output.
    A
    DTC B1628, B1647, B1648 or 82 is output.
    B
    DTCs B1623, B1628, B1642, B1643, B1647, B1648, 81 and 82 are not output.
    C

    HINT:
    Codes other than DTCs B1623, B1628, B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


13.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238223E01
  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1623, B1628, B1642, B1643, B1647, B1648, 81 and 82 are not output.
    A
    DTC B1623, B1642, B1643 or 81 is output.
    B
    DTC B1628, B1647, B1648 or 82 is output.
    C

    HINT:
    Codes other than DTCs B1623, B1628, B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly RH



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

14.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


15.CHECK NO. 2 FLOOR WIRE (OPEN)


    C240589E03
  1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - O11-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


16.CHECK NO. 2 FLOOR WIRE (SHORT)


    C238222E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - O11-2 (BCR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


17.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238222E03
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    O11-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


18.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238222E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    O11-2 (BCR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Connect the connector to the side No. 2 airbag sensor assembly RH.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 or B1633 is output.
    A
    DTC B1637 or B1638 is output.
    B
    DTCs B1632, B1633, B1637 and B1638 are not output.
    C

    HINT:
    Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


20.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238223E01
  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1632, B1633, B1637 and B1638 are not output.
    A
    DTC B1632 or B1633 is output.
    B
    DTC B1637 or B1638 is output.
    C

    HINT:
    Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly RH



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

21.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1622 and B1627 are not output.
    A
    DTC B1622 is output.
    B
    DTC B1627 is output.
    C

    HINT:
    Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)