CONDENSER > REMOVAL |
| 1. PRECAUTION |
| 2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM |
Turn the A/C switch on.
Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.
Turn the ignition switch off.
Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. REMOVE FRONT BUMPER ASSEMBLY |
| 5. REMOVE BATTERY (for 2GR-FE) |
| 6. REMOVE INLET AIR CLEANER ASSEMBLY (for 2AR-FE) |
![]() |
Remove the 2 bolts and inlet air cleaner assembly.
| 7. REMOVE INLET NO. 2 AIR CLEANER (for 2GR-FE) |
![]() |
Disconnect the 2 wire harness clamps and vacuum hose clamp.
Remove the 2 bolts and inlet No. 2 air cleaner.
| 8. REMOVE INLET NO. 1 AIR CLEANER (for 2GR-FE) |
![]() |
Disengage the pin and remove the inlet No. 1 air cleaner.
| 9. REMOVE RADIATOR RESERVE TANK ASSEMBLY (for 2AR-FE) |
![]() |
Disconnect the radiator reserve tank hose.
Remove the 2 bolts and radiator reserve tank assembly.
| 10. REMOVE RADIATOR RESERVE TANK ASSEMBLY (for 2GR-FE) |
![]() |
Disconnect the radiator reserve tank hose.
Remove the 2 bolts and radiator reserve tank assembly.
| 11. REMOVE HOOD LOCK ASSEMBLY (for LHD) |
![]() |
Using a screwdriver, remove the hood lock nut cap.
| *1 | Protective Tape |
![]() |
Disconnect the connector.
![]() |
Remove the 2 bolts and hood lock bolt.
| *1 | Hood Lock Bolt |
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock assembly.
| 12. REMOVE HOOD LOCK ASSEMBLY (for RHD) |
![]() |
Using a screwdriver, remove the hood lock nut cap.
| *1 | Protective Tape |
![]() |
Disconnect the connector.
![]() |
Remove the 2 bolts and hood lock bolt.
| *1 | Hood Lock Bolt |
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock assembly.
| 13. REMOVE UPPER RADIATOR SUPPORT (for 2AR-FE) |
![]() |
Disconnect the 2 connectors.
![]() |
Disconnect the hood lock control cable clamp and remove the 5 bolts and upper radiator support.
| *A | for RHD: |
| *B | for LHD: |
Remove the 2 radiator support cushions.
| 14. REMOVE UPPER RADIATOR SUPPORT (for 2GR-FE) |
![]() |
Disconnect the 2 connectors.
![]() |
Disconnect the hood lock control cable clamp and remove the 5 bolts and upper radiator support.
Remove the 2 radiator support cushions from the radiator assembly.
| 15. REMOVE RADIATOR SIDE DEFLECTOR LH |
![]() |
Disengage the 3 claws and guide remove the radiator side deflector LH.
| 16. REMOVE RADIATOR SIDE DEFLECTOR RH |
![]() |
Disengage the 3 claws and guide remove the radiator side deflector RH.
| 17. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
![]() |
Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the condenser.
Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
| 18. DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
![]() |
Remove the bolt and disconnect the air conditioner tube and accessory assembly from the condenser.
Remove the O-ring from the air conditioner tube and accessory assembly.
| 19. REMOVE COOLER CONDENSER ASSEMBLY |
![]() |
Remove the 4 bolts.
![]() |
Disengage the 2 guides and remove the cooler condenser assembly as shown in the illustration.