Home › Engine / Hybrid System · 1AZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2237
An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
  1. Open in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2238
  1. Case 1:
    Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic):
    1. Voltage at terminal A1A+ is 0.5 V or less.
    2. Voltage difference between terminals A1A+ and A1A- is 0.1 V or less.
  2. Case 2:
    Air fuel ratio sensor admittance is less than 0.015 1/Ω (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2239
The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2252
The A1A- voltage is 0.5 V or less (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2253
The A1A- voltage is higher than 4.5 V (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the air fuel ratio sensor circuit, or if the air fuel ratio sensor output drops. To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the ignition switch to ON, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is higher than 0.5 V, or 4.5 V or less, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM determines that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in next driving cycle, the MIL is illuminated and a DTC is stored.

MONITOR STRATEGY


Required Sensors/Components
Air fuel ratio sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on.
  6. Start the engine and wait 5 minutes or more.
  7. Enter the following menus: Powertrain / Engine and ECT / DTC.
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P2237, P2238, P2239, P2252 or P2253.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  4. Refer to "Data List / Active Test" [AFS Voltage B1S1] (Click here).

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E19-1 (HA1A) - E83-109 (HA1A)
    Always
    Below 1 Ω
    E19-3 (A1A+) - E83-112 (A1A+)
    Always
    Below 1 Ω
    E19-4 (A1A-) - E83-113 (A1A-)
    Always
    Below 1 Ω
    E19-1 (HA1A) or E83-109 (HA1A) - Body ground
    Always
    10 kΩ or higher
    E19-3 (A1A+) or E83-112 (A1A+) - Body ground
    Always
    10 kΩ or higher
    E19-4 (A1A-) or E83-113 (A1A-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2237, P2238, P2239, P2252 or P2253.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2237, P2238, P2239, P2252 or P2253 is output)
    B



B
REPLACE ECM (Click here)
A

END