Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

Using this circuit, the radio receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly sends microphone signals to the radio receiver assembly.

WIRING DIAGRAM


E204785E02


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the radio receiver assembly and roof console box assembly (telephone microphone assembly) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I150-6 (SNS2) - S7-15 (SNS2)
    Always
    Below 1 Ω
    I150-4 (MACC) - S7-14 (MACC)
    Always
    Below 1 Ω
    I150-5 (MIN+) - S7-13 (MCO+)
    Always
    Below 1 Ω
    I150-19 (MIN-) - S7-12 (MCO-)
    Always
    Below 1 Ω
    I150-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    I150-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    I150-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    I150-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    I150-18 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT RADIO RECEIVER ASSEMBLY
  1. Reconnect the radio receiver assembly connector.

  1. Reconnect the roof console box assembly (telephone microphone assembly) connector.



    E176671E61
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I150-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I150-18 (SGND) - Body ground
    Always
    Below 1 Ω
    I150-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio Receiver Assembly)



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Disconnect the roof console box assembly (telephone microphone assembly) connector.



    E187117E13
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S7-12 (MCO-) - S7-15 (SNS2)
    Always
    Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Roof console box Assembly (Telephone microphone assembly))


NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
OK


4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Reconnect the radio receiver assembly connector.



    E187122E14
  1. Reconnect the roof console box assembly (telephone microphone assembly) connector.

  1. Turn the ignition switch to ACC.

  1. Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the roof console box assembly (telephone microphone assembly) connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the roof console box assembly is output
    A
    A waveform synchronized with the voice input to the roof console box assembly is not output
    B

Text in Illustration 
*a
Component with harness connected
(Roof console box Assembly (Telephone microphone assembly))


B
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)