AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Microphone Circuit between Microphone and Radio Receiver |

| 1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)) |
Disconnect the radio and display receiver assembly connector.
Disconnect the roof console box assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-6 (SNS2) - S7-15 (SNS2) | Always | Below 1 Ω |
| I155-4 (MACC) - S7-14 (MACC) | Always | Below 1 Ω |
| I155-5 (MIN+) - S7-13 (MCO+) | Always | Below 1 Ω |
| I155-19 (MIN-) - S7-12 (MCO-) | Always | Below 1 Ω |
| I155-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| I155-4 (MACC) - Body ground | Always | 10 kΩ or higher |
| I155-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| I155-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| I155-18 (SGND) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY |
Reconnect the radio and display receiver assembly connector.
Reconnect the roof console box assembly (telephone microphone assembly) connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-4 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-18 (SGND) - Body ground | Always | Below 1 Ω |
| I155-19 (MIN-) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
|
| ||||
| OK | |
| 3.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
Disconnect the roof console box assembly (telephone microphone assembly) connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S7-15 (SNS2) - S7-12 (MCO-) | Always | Below 1 Ω |
| *a | Component without harness connected (Roof Console Box Assembly (Telephone Microphone Assembly)) |
|
| ||||
| OK | |
| 4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
Reconnect the radio and display receiver assembly connector.
Reconnect the roof console box assembly (telephone microphone assembly) connector.
Turn the ignition switch to ACC.
![]() |
Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the roof console box assembly (telephone microphone assembly) connector.
Check the waveform of the telephone microphone assembly using the oscilloscope.
| Result | Proceed to |
| A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output | A |
| A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output | B |
| *a | Component with harness connected (Roof Console Box Assembly (Telephone Microphone Assembly)) |
|
| ||||
| A | ||
| ||