INTAKE MANIFOLD > REMOVAL |
| 1. PRECAUTION |
| 2. DISCHARGE FUEL SYSTEM PRESSURE |
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Loosen the cylinder block drain cock plug (for Bank 1).
Loosen the cylinder block drain cock plug (for Bank 2, w/ Cylinder Block Drain Cock Plug).
Remove the radiator cap sub-assembly.

| *1 | Radiator Cap Sub-assembly | *2 | Cylinder Block Drain Cock Plug (for Bank 1) |
| *3 | Cylinder Block Drain Cock Plug (for Bank 2, w/ Cylinder Block Drain Cock Plug) | *4 | Radiator Drain Cock Plug |
| *5 | Air Drain Cock Plug | - | - |
| 5. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 6. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Remove the 10 bolts and front outer cowl top panel sub-assembly.
| 7. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 retainers on the front of the V-bank cover sub-assembly. Continue to raise the V-bank cover sub-assembly to disengage the retainer on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.
| 8. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the mass air flow meter connector and wire harness clamp.
![]() |
Disconnect the 3 hoses.
Separate the ventilation hose.
![]() |
Loosen the hose clamp and separate the air cleaner cap sub-assembly from the throttle with motor body assembly.
Release the 2 clamps and remove the air cleaner cap with hose.
| 9. REMOVE INTAKE AIR SURGE TANK ASSEMBLY |
![]() |
Disconnect the ventilation hose.
| *A | Type A |
| *B | Type B |
Disconnect the hose clamp and union to check valve hose.
![]() |
Disconnect the connector and wire harness clamp.
Disconnect the 2 water by-pass hoses and fuel vapor feed hose.
![]() |
Disconnect the connector from the intake air control valve assembly.
![]() |
Remove the bolt and vacuum hose clamp.
![]() |
Remove the bolt and separate the throttle body bracket from the intake air surge tank assembly.
![]() |
Remove the bolt and separate the No. 1 surge tank stay from the intake air surge tank assembly.
![]() |
Remove the 2 nuts from the intake air surge tank assembly.
Using a 5 mm socket hexagon wrench, remove the 4 bolts.
![]() |
Remove the intake air surge tank assembly and 3 gaskets.
| 10. REMOVE NO. 2 ENGINE MOUNTING STAY RH (for Engine Mounting stay Side) |
![]() |
Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.
| 11. REMOVE NO. 2 ENGINE MOUNTING STAY RH (for Intake Manifold Side) |
![]() |
Remove the bolt and No. 2 engine mounting stay RH.
| 12. DISCONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Remove the No. 2 fuel pipe clamp.
| *1 | No. 2 Fuel Pipe Clamp |
| *2 | Fuel Tube Connector |
| *3 | Nylon Tube |
| *4 | O-ring |
| *5 | Fuel Pipe |
![]() | Pinch |
![]() | Pull |
Pinch the tube connector and pull out the fuel pipe.
| 13. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY |
![]() |
Disconnect the 6 fuel injector connectors.
![]() |
Remove the 5 bolts and fuel delivery pipe sub-assembly together with the 6 fuel injectors.
![]() |
Remove the 6 injector vibration insulators from the intake manifold.
| 14. REMOVE INTAKE MANIFOLD |
![]() |
Remove the 6 bolts, 4 nuts and intake manifold.
| *A | Type A |
| *B | Type B |
![]() |
Remove the 2 gaskets.