Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System)

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

  1. w/o Wireless Door Lock Buzzer Answer Back Function:
    When the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high, the ECM stores this DTC.
  2. w/ Wireless Door Lock Buzzer Answer Back Function:
    When the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B279A
The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 is stuck high (1 trip detection logic*3).
  1. Wire harness or connector (disconnection or break in wire harness is main cause)
  2. ID code box (immobiliser code ECU)*1
  3. Certification ECU (smart key ECU assembly)*2
  4. Telephone transceiver assembly*4
  5. ECM
Turn the engine switch on (IG) and wait 6 seconds.
  1. *1: w/o Wireless Door Lock Buzzer Answer Back Function
  2. *2: w/ Wireless Door Lock Buzzer Answer Back Function
  3. *3: Only output while a malfunction is present.
  4. *4: w/ Blocking System

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops)
Engine cannot be started

Related Data List and Active Test 
DTC Code
Data List and Active Test
B279A
-

WIRING DIAGRAM


w/o Blocking System

B278904E01


w/ Blocking System

B278905E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or telephone transceiver assembly*, refer to the Service Bulletin.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
  3. When the telephone transceiver is replaced, it is necessary to set the contract mode.*

  1. *: w/ Blocking System

HINT:
When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Turn the engine switch on (IG) and wait 10 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B

    HINT:
    If DTCs other than DTC B279A are output, troubleshoot those DTCs first.



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.CHECK CONNECTION OF CONNECTOR
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

    OK:
    Connectors are properly connected.

    Result:
    Result
    Proceed to
    OK (w/ Blocking System)
    A
    OK (w/o Blocking System)
    B
    NG
    C



B
Go to step 10

C
CONNECT CONNECTORS PROPERLY
A


4.CHECK HARNESS AND CONNECTOR (ECM - TELEPHONE TRANSCEIVER ASSEMBLY)
  1. Disconnect the I70 ECU connector.

  1. Disconnect the A25 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I70-8 (BLK3) - A25-31 (IMI)
    Always
    Below 1 Ω
    A25-31 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - TELEPHONE TRANSCEIVER ASSEMBLY)
  1. Disconnect the A43 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I70-2 (BLK4) - A43-13 (EFIO)
    Always
    Below 1 Ω
    A43-13 (EFIO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
  1. Temporarily replace the telephone transceiver assembly with a new or known good one.

    HINT:
    Refer to the Service Bulletin.


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


8.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.



NG
Go to step 16
OK

END (TELEPHONE TRANSCEIVER ASSEMBLY WAS DEFECTIVE) 

10.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU)*3 OR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)*4 - ECM)
  1. Disconnect the A25 ECM connector.

  1. Disconnect the I20*3 or A43*4 ECU connector.

    1. *3: w/o Wireless Door Lock Buzzer Answer Back Function
    2. *4: w/ Wireless Door Lock Buzzer Answer Back Function

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-4 (EFIO) - A25-31 (IMI)*3
    A43-13 (EFIO) - A25-31 (IMI)*4
    Always
    Below 1 Ω
    A25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-4 (EFIO) - A25-28 (IMI)*3
    A43-13 (EFIO) - A25-28 (IMI)*4
    Always
    Below 1 Ω
    A25-28 (IMI) - Body ground
    Always
    10 kΩ or higher

    1. *3: w/o Wireless Door Lock Buzzer Answer Back Function
    2. *4: w/ Wireless Door Lock Buzzer Answer Back Function

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    A25-31 (IMI) - Body ground
    Always
    Below 1 V
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    A25-28 (IMI) - Body ground
    Always
    Below 1 V

    Result:
    Result
    Proceed to
    OK (w/o Wireless Door Lock Buzzer Answer Back Function)
    A
    OK (w/ Wireless Door Lock Buzzer Answer Back Function)
    B
    NG
    C



B
Go to step 16

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


11.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
  1. Replace the ID code box (immobiliser code ECU) with a new one.

    HINT:
    Refer to the Service Bulletin.


NEXT


12.REGISTER RECOGNITION CODES
  1. Register the recognition codes in the ECUs.

    HINT:
    Refer to the Service Bulletin.


NEXT


13.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


14.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


15.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE)
    B
    NG (for 2AR-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE) 

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to the Service Bulletin.


NEXT


17.REGISTER RECOGNITION CODES
  1. Register the key.

    HINT:
    Refer to the Service Bulletin.


NEXT


18.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


19.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


20.CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE)
    B
    NG (for 2AR-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))