Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD)

BRAKE BOOSTER (for RHD) > INSTALLATION

for Preparation Click here



1. INSTALL CHECK VALVE GROMMET
  1. Install a new check valve grommet to the brake booster assembly.



2. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY
  1. Install the brake vacuum check valve assembly to the brake booster assembly.



3. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.



    C105620E05
  1. Set the push rod length as shown in the illustration.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Brake Master Cylinder Push Rod Clevis
    *a
    Push Rod Length

    Push rod length:
    148.6 to 149.6 mm (5.86 to 5.88 in.)

  1. Tighten the lock nut.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



4. INSTALL BRAKE BOOSTER GASKET
  1. Install a new brake booster gasket to the brake booster assembly.



5. INSTALL BRAKE BOOSTER ASSEMBLY
  1. Install the brake booster assembly to the vehicle body with the 4 nuts.

    Torque:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not kink or damage the brake lines, air conditioning tube and accessory assembly or suction pipe sub-assembly.



6. INSTALL PUSH ROD PIN


    C259403
  1. Apply lithium soap base glycol grease to the push rod pin.
    Text in Illustration 
    V100145
    Lithium Soap Base Glycol Grease

  1. Connect the brake master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip as shown in the illustration.

    NOTICE:
    1. Be sure to insert the pin with its clip end facing the outside of the vehicle.
    2. Make sure that the brake master cylinder push rod clevis moves sideway.



7. CONNECT UNION TO CHECK VALVE HOSE
  1. Connect the union to check valve hose to the brake booster assembly, and slide the clip to secure it.



8. INSTALL VACUUM SWITCHING VALVE ASSEMBLY
  1. Install the vacuum switching valve assembly with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 2 vacuum hoses and connector.

  1. Connect the union to check valve hose and wire harness clamp.



9. CONNECT BRAKE LINE


    C239879
  1. Install 2 new clamps to the brake lines.

  1. Using a union nut wrench, connect the 2 brake lines to the brake actuator assembly.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Do not kink or damage the brake lines.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake lines.
    3. Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



10. INSTALL NO. 1 BRAKE TUBE CLAMP


    C239890
  1. Install a new No. 1 brake tube clamp to the vehicle body.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Engage the brake lines to the clamp.

    NOTICE:
    Do not kink or damage the brake lines.



11. INSTALL SUCTION PIPE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the openings of the disconnected parts.

  1. Sufficiently apply compressor oil to a new O-ring, fitting surface of the suction pipe sub-assembly and air conditioning unit.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the suction pipe sub-assembly.

    NOTICE:
    Keep the O-ring and O-ring fitting surfaces free from dirt or any foreign matter.



    C239887
  1. Insert the suction pipe sub-assembly to the air conditioning unit.

    NOTICE:
    1. Insert the pipe joint into the fitting hole securely.
    2. Do not deform the piping.
    3. Do not damage the plastic clamp.



    C239876
  1. Install the clamp with suction pipe sub-assembly and air conditioning tube and accessory assembly to the No. 1 brake tube clamp.

    NOTICE:
    1. Do not deform the air conditioning tube and accessory assembly or suction pipe sub-assembly.
    2. Do not damage the plastic clamp.



    C239896
  1. Install the clamp to the brake actuator bracket assembly.

    NOTICE:
    1. Do not deform the suction pipe sub-assembly.
    2. Do not damage the plastic clamp.



12. INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
  1. Remove the attached vinyl tape from the openings of the disconnected parts.

  1. Sufficiently apply compressor oil to 2 new O-rings, the fitting surface of the air conditioning tube and accessory assembly, cooler condenser assembly and air conditioning unit.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings on the air conditioning tube and accessory assembly.

    NOTICE:
    Keep the O-ring and O-ring fitting surfaces free from dirt or any foreign matter.

  1. Insert the air conditioning tube and accessory assembly to the cooler condenser assembly.

  1. Install the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    C239873
  1. Insert the air conditioning tube and accessory assembly to the air conditioning unit.

    NOTICE:
    Insert the pipe joint into the fitting hole securely.

  1. Turn the hook connector and install the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    C239874
  1. Install the clamp to the vehicle body and connect the pressure sensor connector.

    NOTICE:
    1. Do not deform the piping.
    2. Do not damage the plastic clamp.



13. INSTALL RADIATOR SIDE DEFLECTOR RH
  1. Engage the guide and 3 claws to install the radiator side deflector RH.



14. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
(Click here)


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



16. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump or appropriate equipment.



  1. Charge the air conditioning system with refrigerant.

    Refrigerant type:
    HFC-134a (R134a)



    E143108E11


    Text in Illustration 
    *a
    Sub-cool System
    *b
    High Pressure
    *c
    Refrigerant Amount
    *d
    Standard charge amount
    *e
    Charge additional 100 g (3.5 oz.)
    *f
    Point where bubbles disappear
    *g
    Mean value in proper range
    *h
    Overcharged

    Standard charge amount:
    450 to 550g (15.9 to 19.4oz.)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to work without refrigerant, resulting in overheating of the compressor.
    2. The refrigerant amount should be checked by quantity (weight).

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.



17. WARM UP ENGINE
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing air conditioning system lines (including the compressor).



18. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Ignition switch off.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases which are not refrigerant, such as gasoline vapor and exhaust gas).
    3. Repeat the inspection 2 or 3 times.
    4. Measure the pressure to make sure that there is some refrigerant remaining in the air conditioning system.
      Pressure when the compressor is off: approx. 392 to 588 kPa (3.9 to 5.9 kgf/cm2, 57 to 85 psi)



    I042222E40
  1. Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Inspect for Leak



    N014519E08
  1. Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *2
    Drain Hose

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
    2. Bring the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow checking for leaks.

  1. If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.

  1. Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.

    HINT:
    When checking for leaks, the presence of oily dirt at a joint can indicate a leak.



19. INSTALL FRONT BUMPER COVER
(Click here)


20. INSPECT AND ADJUST BRAKE PEDAL
(Click here)