Home › Engine / Hybrid System ยท 1AZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P1607    Cruise Control Input Processor

for Preparation Click here


MONITOR DESCRIPTION

The ECM continuously monitors its main CPU. This self-check ensures that the ECM is functioning properly. If outputs from main CPU is deviate from the standard, the ECM illuminates the MIL and stores the DTC immediately.

DTC No.
DTC Detection Condition
Trouble Area
P1607
An ECM main CPU malfunction (1 trip detection logic).
ECM

MONITOR STRATEGY


Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
Cruise control
Frequency of Operation
Continuous

TYPICAL MALFUNCTION THRESHOLDS


All of the following conditions are met
-
Cruise control
Forbiddance
Either of the following conditions is met
1 or 2
1. Cruise control
Operating
2. Low speed control
Operating

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the tester off.
  5. Turn the ignition switch off.
  6. Disconnect the tester.
  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) battery terminal.
  9. Connect the tester to the DLC3.
  10. Turn the ignition switch to ON and turn the tester on.
  11. Wait 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine and ECT / DTC.
  13. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P1607.
  16. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


INSPECTION PROCEDURE

NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ OUTPUT DTC (DTC P1607)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the tester off.

  1. Turn the ignition switch off.

  1. Disconnect the tester.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Wait 16 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P1607 is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)