PARKING ASSIST MONITOR SYSTEM > CALIBRATION |
| ADJUST PARKING ASSIST MONITOR SYSTEM |
This parking assist monitor system can be adjusted using the diagnostic screen of the display.
If the following operations are performed, it is necessary to perform adjustments and checks using the diagnostic screen.
| Part Name | Operation | Adjustment Item | Proceed to |
| Spiral cable with sensor sub-assembly | Removal and installation of the Spiral cable with sensor sub-assembly | Steering angle setting | Procedure 3 |
| Replacement | Steering angle neutral point (Initialize parking assist monitor system) |
Click here
| |
| Steering angle setting | Procedure 3 | ||
| Spiral cable sub-assembly | Removal and installation of the spiral cable sub-assembly | Steering angle setting | Procedure 3 |
| Replacement | Steering angle neutral point (Initialize parking assist monitor system) |
Click here
| |
| Steering angle setting | Procedure 3 | ||
| Navigation ECU sub-assembly | Replacement | Navigation ECU sub-assembly | Procedure 1 |
| Steering sensor | Replacement | Steering angle neutral point (Initialize parking assist monitor system) |
Click here
|
| Steering angle setting | Procedure 3 | ||
| Steering angle neutral point (Initialize parking assist monitor system) |
Click here
| |
| Steering angle setting | Procedure 3 | ||
| Suspension, tires, etc. | The vehicle height changes because of suspension or tire replacement | Rear television camera assembly optical axis (Back camera position setting) | Procedure 2 |
| Rear television camera assembly |
| Rear television camera assembly optical axis (Back camera position setting) | Procedure 2 |
| NAVIGATION ECU SUB-ASSEMBLY (PROCEDURE 1) |
Preparation for adjustment
Park the vehicle with the steering wheel centered.
![]() |
Set a target bar for optical axis adjustment of the rear television camera assembly.
| Area | Specification |
| A | 1241 to 1251 mm (4.071 to 4.104 ft.) |
| B | 1995 to 2005 mm (6.545 to 6.578 ft.) |
| *a | Vehicle Center |
| *b | Target Bar for Back Camera Adjustment |
| *c | Vehicle End |
| *d | Front |
Start diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" on the Service Menu screen.
![]() |
Select "Camera Setting" on the Function Check/Setting screen.
![]() |
Select "Next" on the Car Information Check screen.
![]() |
Select "Next" on the Car Signal Check screen.
Steering Angle Setting
![]() |
Perform the STEERING CENTER MEMORIZE operation.
Perform the MAX STEERING ANGLE MEMORIZE operation.
![]() |
Back Camera Position Setting
Perform roll angle adjustment.
Perform vertical and horizontal position adjustment.
Select the "Next" button on the Back Camera Position Setting screen.
![]() |
Back Verify Mode
Check that A and the target adjustment bar are overlapping.
Selecting "OK" will return to the Service Menu screen, and complete the adjustment.
Finish diagnostic mode (Click here).
Confirm steering angle adjustment.
Check on the parking assist screen that the predicted path line moves until the steering wheel is fully turned to either the left or right.
| BACK CAMERA POSITION SETTING (PROCEDURE 2) |
Preparation for adjustment
Park the vehicle with the steering wheel centered.
![]() |
Set a target bar behind the vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).
| Area | Specification |
| A | 1241 to 1251 mm (4.071 to 4.104 ft.) |
| B | 1995 to 2005 mm (6.545 to 6.578 ft.) |
| *a | Vehicle Center |
| *b | Target Bar for Back Camera Position Setting |
| *c | Vehicle End |
| *d | Front |
Start diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" on the Service Menu screen.
![]() |
Select "Camera Setting" on the Function Check/Setting screen.
![]() |
Select "Next" on the Car Information Check screen.
![]() |
Select "Back Camera Setting" on the Mode Setting screen.
![]() |
Select "Next" on the Car Signal Check screen.
![]() |
Back Camera Position Setting
Perform roll angle adjustment.
Perform vertical and horizontal position adjustment.
Select the "Next" button on the "Back Camera Position Setting" screen.
![]() |
Back Verify Mode
Check that A and the target adjustment bar are overlapping.
Selecting "OK" will return to the Service Menu, and complete the adjustment.
Finish diagnostic mode (Click here).
| Steering Angle Setting (Procedure 3) |
Center the steering wheel and stop the vehicle.
Start diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" on the Service Menu screen.
![]() |
Select "Camera Setting" on the Function Check/Setting screen.
![]() |
Select "Next" on the Car Information Check screen.
![]() |
Select "Steering Angle Setting" on the Mode Setting screen.
![]() |
Select "Next" on the Car Signal Check screen to display the Steering Angle Setting screen.
![]() |
Steering Angle Setting
Check that the steering wheel is centered (approximately +/- 5 degrees or less) and select "STEERING CENTER MEMORIZE".
After the centered steering position is memorized, turn the steering wheel to the left and then to the right full lock positions and select "MAX STEERING ANGLE MEMORIZE".
Select "MAX STEERING ANGLE MEMORIZE" to store the steering angle adjustment value and change the screen to the Mode Setting screen.
Finish diagnostic mode (Click here).
Confirm steering angle adjustment.
Check on the parking assist screen that the predicted path line moves until the steering wheel is fully turned to either the left or right.