FUEL LID LOCK CONTROL CABLE ASSEMBLY (for LHD) > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat) |
| 3. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat) |
| 4. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 10 claws and remove the front door scuff plate LH.
| 5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Disconnect the front door opening trim weatherstrip.
| 6. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Disengage the 6 claws and remove the rear door scuff plate LH.
| 7. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Remove the rear door opening trim weatherstrip LH.
| 8. REMOVE LAP BELT OUTER ANCHOR COVER |
![]() |
Disengage the 3 claws and remove the lap belt outer anchor cover.
| 9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.
| 10. REMOVE CENTER PILLAR LOWER GARNISH LH |
![]() |
Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.
| 11. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
![]() |
Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 12. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Disengage the claw and remove the rear seat cushion lock hook.
| 13. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly LH.
| 14. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
![]() |
Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
Repeat the step above for the other hook.
w/ Seat Heater System:
Disconnect the 2 seat heater connectors.
Remove the rear seat cushion assembly.
| 15. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Disengage the claw and remove the rear seat cushion lock hook.
| 16. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 17. REMOVE REAR SEATBACK COVER (for Reclining Seat Type) |
![]() |
Disengage the 4 claws and remove the 2 rear seatback covers.
| 18. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type) |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.
Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly LH.
| 19. REMOVE REAR SEAT SIDE GARNISH LH (for Reclining Seat Type) |
![]() |
Remove the bolt.
Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.
| 20. REMOVE LUGGAGE COMPARTMENT DOOR COVER |
![]() |
Remove the 13 clips and luggage compartment door cover.
| 21. REMOVE LUGGAGE COMPARTMENT FLOOR MAT |
Remove the luggage compartment floor mat.
| 22. REMOVE BAGGAGE HOLDER NET (w/ Partition Net) |
Remove the baggage holder net.
| 23. REMOVE REAR FLOOR FINISH PLATE |
![]() |
Remove the 5 clips.
![]() |
Disengage the 4 clips and remove the rear floor finish plate.
| 24. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
![]() |
Push the pin and remove the No. 1 luggage compartment trim hook.
| *1 | Pin |
| 25. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH |
![]() |
Remove the 3 clips.
Disengage the fastener and remove the luggage compartment inner trim cover LH.
| 26. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
![]() |
Remove the screw.
![]() |
Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.
![]() |
Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.
| 27. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
![]() |
Disengage the 2 clamps.
![]() |
Disengage the clamp and disconnect the wire harness.
![]() |
Disengage the 2 clamps and remove the 2 scuff plate clips.
Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.
![]() |
Disengage the guide as shown in the illustration.
![]() |
Disconnect the luggage door lock control cable sub-assembly.
![]() |
Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.
![]() |
Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.
| *1 | Cutout |
| *2 | Guide <A> |
![]() |
Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.
| *1 | Cutout |
| *2 | Guide <B> |
![]() |
Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.
| *1 | Cutout |
| *2 | Guide <C> |
| *3 | Guide <B> |
![]() |
Disengage the 2 claws and remove the fuel filler opening lid lock retainer.
Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

| *1 | Fuel Lid Lock Control Cable Sub-assembly | *2 | Luggage Door Lock Control Cable Sub-assembly |
Using a knife, cut off the clamp as shown in the illustration.

| *1 | Tape | - | - |
| *a | Cut | - | - |
Remove the clamp.
Remove the 3 pieces of tape and fuel lid lock control cable sub-assembly.