Home › Vehicle Exterior › LIGHTING (EXT) › HAZARD WARNING SWITCH

HAZARD WARNING SWITCH > INSTALLATION

for Preparation Click here



1. INSTALL HEATER CONTROL SWITCH BOARD

NOTICE:
When resassembling the air conditioning control assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



    E228096
  1. Install the heater control base sub-assembly with the 5 screws.



2. INSTALL HEATER CONTROL HOUSING SUB-ASSEMBLY


    E232143
  1. Engage the 4 claws.

  1. Install the heater control housing sub-assembly to the heater control retainer RH with the 3 screws.



3. INSTALL AIR CONDITIONING PANEL SUB-ASSEMBLY


    E234926
  1. Engage the 7 claws.



    E234925
  1. Install the air conditioner panel sub-assembly with the 2 screws.



4. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (HAZARD SWITCH)


    E232141
  1. Engage the guide and 4 clips to install the air conditioning control assembly as shown in the illustration.



5. INSTALL NO. 1 RADIO BRACKET (w/o Navigation System)
  1. Install the No. 1 radio bracket with the 5 screws.



6. INSTALL NO. 2 RADIO BRACKET (w/o Navigation System)
  1. Install the No. 2 radio bracket with the 5 screws.



7. INSTALL NO. 1 RADIO RECEIVER BRACKET (w/ Navigation System)
  1. Install the No. 1 radio receiver bracket with the 5 screws.



8. INSTALL NO. 2 RADIO RECEIVER BRACKET (w/ Navigation System)
  1. Install the No. 2 radio receiver bracket with the 5 screws.



9. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)
  1. Connect each connector.

  1. Engage the 6 clips to the vehicle body to temporarily install the radio receiver assembly with air conditioning control assembly.

  1. Install the radio receiver assembly with air conditioning control assembly with the 4 bolts.



10. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)
  1. Connect each connector.

  1. Engage the 6 clips to the vehicle body to temporarily install the navigation receiver assembly with air conditioning control assembly.

  1. Install the navigation receiver assembly with air conditioning control assembly with the 4 bolts.



11. INSTALL FRONT CONSOLE UPPER PANEL GARNISH


  1. for Blank Type:



      B284923
    1. Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.



  1. for 3 Switch Hole Type:

    1. Connect each connector.



    2. B281753
    3. Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.



12. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
  1. Connect the connector.



    B281760
  1. Engage the 4 clips to install the No. 2 instrument panel register assembly.

    NOTICE:
    When installing the No. 2 instrument panel register assembly, check that the wire harness is not caught between the No. 2 instrument panel register assembly and duct.



13. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B283351
  1. Engage the 7 clips and 2 guides to install the center instrument cluster finish panel sub-assembly.



14. INSTALL FRONT PANEL GARNISH RH


    B280333
  1. Engage the 3 clips and 8 guides to install the front panel garnish RH.



15. INSTALL FRONT PANEL GARNISH LH


    B281945
  1. Engage the 3 clips and 8 guides to install the front panel garnish LH.



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Navigation System)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).