MAIN BODY ECU > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FRONT PANEL GARNISH LH (for LHD) |
![]() |
Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.
| 4. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD) |
![]() |
Disengage the 10 claws and remove the front door scuff plate LH.
| 5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 6. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD) |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 7. REMOVE INSTRUMENT SIDE PANEL LH (for LHD) |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 8. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD) |
![]() |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
| 9. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Remove the 2 bolts <B>.
w/o Driver Side Knee Airbag:
![]() |
Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.
w/ Driver Side Knee Airbag:
![]() |
Disengage the 4 claws, 7 clips and 3 guides to remove the instrument panel sub-assembly.
| 10. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY (for LHD with Driver Side Knee Airbag) |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Remove the 4 bolts.
Disengage the 2 claws to disconnect the DLC3.
![]() |
Disengage the 2 hooks to remove the lower No. 1 instrument panel airbag assembly.
![]() |
Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.
| *1 | Protective Tape |
| *2 | Airbag Connector |
| *3 | Airbag Connector Lock |
Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.
| 11. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD) |
![]() |
Disconnect the 5 connectors.
![]() |
Remove the bolt, 2 nuts and disconnect the instrument panel junction block assembly.
![]() |
Disengage the claw and disconnect the connector as shown in the illustration.
![]() |
Disengage the claw and release the connector lock as shown in the illustration.
![]() |
Disengage the claw and disconnect the connector as shown in the illustration.
Remove the instrument panel junction block assembly.
| 12. REMOVE FRONT PANEL GARNISH LH (for RHD) |
![]() |
Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.
| 13. REMOVE FRONT DOOR SCUFF PLATE LH (for RHD) |
![]() |
Disengage the 10 claws and remove the front door scuff plate LH.
| 14. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 15. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD) |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 16. REMOVE INSTRUMENT SIDE PANEL LH (for RHD) |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 17. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the 4 claws.
Disengage the 2 guides.
Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.
| 18. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Remove the bolt <B> and screw <C>.
Open the lower instrument panel door.
![]() |
Remove the 3 screws <C>.
![]() |
Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.
| 19. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD) |
![]() |
Disconnect the 5 connectors.
![]() |
Remove the bolt, nut and disconnect the instrument panel junction block assembly.
![]() |
Remove the nut.
Disengage the claw as shown in the illustration and remove the wiring harness clamp bracket.
![]() |
Disengage the claw and disconnect the connector as shown in the illustration.
![]() |
Disengage the claw and release the connector lock as shown in the illustration.
![]() |
Disengage the claw and disconnect the connector as shown in the illustration.
Remove the instrument panel junction block assembly.
| 20. REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
![]() |
Press the claw of the junction block as shown in the illustration to release the lock.
| *1 | Main Body ECU (Multiplex Network Body ECU) |
| *2 | Claw of Driver Side Junction Block |
| *3 | Protective Tape |
With the junction block lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and junction block.
![]() |
Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) up to the position where the connector becomes disengaged.
| *1 | Protective Tape |
![]() |
Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.