Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM

DTC    B1586    Open in Immobiliser Communication Circuit

for Preparation Click here


DESCRIPTION

When the communication line (EFIO - BLK4) between the certification ECU assembly (smart key ECU assembly) and telephone transceiver assembly is open, the telephone transceiver assembly stores DTC B1586.

DTC Code
DTC Detection Condition
Trouble Area
B1586
The communication line (EFIO - BLK4) between the certification ECU assembly (smart key ECU assembly) and telephone transceiver assembly is open.
  1. Telephone transceiver assembly
  2. Certification ECU assembly (smart key ECU assembly)
  3. Wire harness or connector

WIRING DIAGRAM


B278907E01


INSPECTION PROCEDURE

NOTICE:
  1. Before troubleshooting for this DTC, make sure no engine immobiliser system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs first.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. When replacing the telephone transceiver assembly or certification ECU (smart key ECU assembly), refer to the Service Bulletin.
  4. When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

1.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG).

  1. After 6 seconds have elapsed, check for DTCs.

    Result:
    Result
    Proceed to
    DTC is not output.
    A
    Only DTC B1586 is output.
    B
    DTC B1586 and other DTCs are output.
    C



B
Go to step 2

C
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTION OF CONNECTOR
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the telephone transceiver assembly and certification ECU (smart key ECU assembly).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Disconnect the I70 telephone transceiver assembly connector.

  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I70-2 (BLK4) - A43-13 (EFIO)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT)
  1. Reconnect the I70 telephone transceiver assembly connector.

  1. Reconnect the A43 certification ECU (smart key ECU assembly) connector.



  1. Using an oscilloscope, check the waveform.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


    B278908E02


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    *b
    Approximately 160 ms
    *c
    Approximately 270 ms
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    A43-13 (EFIO) - A43-11 (E)
    Tool Setting
    2 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

    OK:
    The waveform is output normally (refer to illustration).



NG
Go to step 5
OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY 

5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - BATTERY AND BODY GROUND)
  1. Disconnect the I70 telephone transceiver assembly connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I70-12 (+B) - Body ground
    Always
    11 to 14 V
    I70-6 (IG2) - Body ground
    Engine switch off
    Below 1 V
    I70-6 (IG2) - Body ground
    Engine switch on (IG)
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I70-9 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to the Service Bulletin.


NEXT


7.PERFORM REGISTRATION
  1. Perform the registration.

    HINT:
    Refer to the Service Bulletin.


NEXT


8.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG).

  1. After 6 seconds have elapsed, check for DTCs.

    OK:
    DTC B1586 is not output.



NG
REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)