Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM

DTC    B1587    Lost Communication for Immobiliser Communication Circuit

for Preparation Click here


DESCRIPTION

When one of the following occurs: 1) the telephone transceiver assembly detects errors in its own communications with the certification ECU (smart key ECU assembly); 2) the telephone transceiver assembly detects errors in the communication lines; 3) the ECU communication ID between the certification ECU (smart key ECU assembly) and telephone transceiver assembly is different and an engine start is attempt, the telephone transceiver assembly stores DTC B1587.

DTC Code
DTC Detection Condition
Trouble Area
B1587
Either condition is met:
  1. Error in communication between telephone transceiver assembly and certification ECU (smart key ECU assembly)
  2. Error in communication lines
  3. Communication ID is different during communication with certification ECU (smart key ECU assembly)
  1. Telephone transceiver assembly
  2. Certification ECU (smart key ECU assembly)
  3. Wire harness or connector

WIRING DIAGRAM


B278907E01


INSPECTION PROCEDURE

NOTICE:
  1. Before troubleshooting for these DTCs, make sure no engine immobiliser system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs first.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. When replacing the telephone transceiver assembly or certification ECU (smart key ECU assembly), refer to the Service Bulletin.
  4. When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

1.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the engine switch off.

  1. Start the engine.

  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.REREGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


3.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the engine switch off.

  1. Start the engine.

  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
Go to step 4
OK

END 

4.CHECK CONNECTION OF CONNECTOR
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the telephone transceiver assembly and certification ECU (smart key ECU assembly).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the I70 telephone transceiver assembly connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I70-1 (BLK1) - A43-14 (EFII)
    Always
    Below 1 Ω
    I70-1 (BLK1) - Body ground
    Always
    10 kΩ or higher
    I70-2 (BLK4) - A43-13 (EFIO)
    Always
    Below 1 Ω
    I70-2 (BLK4) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I70-1 (BLK1) - Body ground
    Always
    Below 1 V
    I70-2 (BLK4) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to the Service Bulletin.


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


8.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the engine switch off.

  1. Start the engine.

  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)