Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280368
  1. Install the front door inside locking cable assembly.



    B280366
  1. Engage the 3 claws.



2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B280365
  1. Install the front door lock remote control cable assembly.



3. INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
  1. When reusing the removed front door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door with motor lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock with motor assembly.



  1. When reusing the front door lock with motor assembly.



      B280363
    1. Install a new door lock wiring harness seal to the front door lock with motor assembly.



    B280362E01
  1. Insert the front door lock open rod to the front door lock with motor assembly.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

  1. Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.

  1. Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder)


    B280352
  1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B280351
  1. Install the hole plug.



5. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B288545
  1. Engage the guide as shown in the illustration.

  1. Install the front door rear lower frame sub-assembly with the 2 bolts.



6. INSTALL FRONT DOOR GLASS RUN


    B281735
  1. Install the front door glass run.



7. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network master switch assembly.



    B288546E01
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.



    B288542
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B281733
  1. Install the grommet.



8. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the front door panel.



    B281685E01
  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
    Text in Illustration 
    *1
    Reference Point

  1. Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.

  1. Engage the 4 clamps.

  1. Connect each connector.



9. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    B288547
  1. Install the front door inner glass weatherstrip.



10. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B277193E01
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly

  1. Connect the connector.



    B288553E01
  1. Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss



    B288551
  1. Engage the 10 clips and install the front door trim board sub-assembly.

  1. Install the 3 screws.

  1. If protective tape has been applied, remove it.



11. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.



    E226715E01
  1. Engage the claw to install the courtesy light assembly.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



12. INSTALL FRONT ARMREST ASSEMBLY


    B277188
  1. Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.



13. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
  1. Connect each connector.



    B288554
  1. Engage the 4 guides, 2 clips and 5 claws, and install the multiplex network master switch assembly with front door armrest base panel.



14. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
  1. Connect the connector.



    B288555
  1. Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.



15. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    B288549
  1. Engage the 3 clips to install the front door lower frame bracket garnish.



16. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B288540
  1. Engage the 3 claws to install the front door inside handle bezel plug.



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



18. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


19. CHECK POWER WINDOW CONTROL SYSTEM
(Click here)