Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK

REAR DOOR LOCK > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280430
  1. Install the rear door inside locking cable assembly.



    B280428
  1. Engage the 3 claws.



2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B280426
  1. Install the rear door lock remote control cable assembly.



    B280424
  1. Engage the claw.



3. INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
  1. When reusing the removed rear door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door with motor lock assembly.

  1. Apply MP grease to the sliding parts of the rear door lock with motor assembly.



  1. When reusing the rear door with motor lock assembly:



      B280422
    1. Install a new door lock wiring harness seal to the rear door lock with motor assembly.



    B280421E01
  1. Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.
    Text in Illustration 
    *1
    Release Plate

  1. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.

  1. Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B281694
  1. Slide the rear door glass sub-assembly to install it as shown in the illustration.



5. INSTALL REAR DOOR QUARTER WINDOW GLASS


    B280411
  1. Install the rear door quarter window glass in the direction indicated by the arrow in the illustration.



6. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B280409
  1. Install the rear door lower window frame sub-assembly with the screw and 2 bolts.



7. INSTALL REAR DOOR GLASS RUN


    B280408
  1. Install the rear door glass run.



8. INSTALL REAR DOOR WEATHERSTRIP


    B288952
  1. Install the upper part of rear door weatherstrip as shown in the illustration.



9. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the rear door panel.



    B281695E01
  1. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
    Text in Illustration 
    *1
    Reference Point

  1. Attach the rear door service hole cover according to the reference points on the rear door panel.

    NOTICE:
    Securely install the rear door service hole cover preventing wrinkles and air bubbles.

  1. Connect the connector.



10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    B280401
  1. Install the rear door inner glass weatherstrip.



11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B280402
  1. Install the No. 1 door scuff plate clamp as shown in the illustration.



    B280397E01
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly

  1. Connect the connector.



    B280395E01
  1. Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss



    B280393
  1. Engage the 8 clips and install the rear door trim board sub-assembly.

  1. Install the 3 screws.

  1. If protective tape has been applied, remove it.



12. INSTALL REAR ARMREST ASSEMBLY


    B280392
  1. Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.



13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
  1. Connect the connector.



    B280390
  1. Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.



14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    B288541
  1. Engage the 3 claws to install the rear door inside handle bezel plug.



15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



16. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


17. CHECK POWER WINDOW CONTROL SYSTEM
(Click here)