Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR SEAT SIDE AIRBAG ASSEMBLY

REAR SEAT SIDE AIRBAG ASSEMBLY > REMOVAL

for Preparation Click here


CAUTION:
  1. Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
  2. If the side airbag was deployed, replace the rear seat airbag assembly, rear seatback frame sub-assembly, separate type rear seatback pad and separate type rear seatback cover with the necessary parts in accordance with the extent of the collision damage (Click here).

HINT:
Use the same procedure for the LH side and RH side.



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing.
for Separate Type Yaw Rate Sensor: (Click here)
for Built-in Type Yaw Rate Sensor: (Click here)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR SEAT HEADREST ASSEMBLY


4. REMOVE REAR SEAT CUSHION ASSEMBLY


    B290774E01
  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the step above for the other hook.

  1. w/ Seat Heater System:

    1. Disconnect the 2 seat heater connectors.

  1. Remove the rear seat cushion assembly.



5. REMOVE REAR SEAT CUSHION LOCK HOOK


    B279203
  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



6. REMOVE REAR SEATBACK COVER


    B281586
  1. Disengage the 4 claws and remove the 2 rear seatback covers.

    HINT:
    Use the same procedure as for the LH side.



7. REMOVE REAR SEATBACK ASSEMBLY
  1. w/ Rear Seat Side Airbag:

    1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.

  1. Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.



    B281589
  1. Disengage the 2 hooks and disconnect the cover.

  1. Remove the 2 nuts, 2 bolts and rear seatback assembly LH.



8. REMOVE REAR SEAT CENTER SHOULDER BELT GUIDE (for LH Side)


    B281606
  1. Remove the 2 screws.

  1. Disengage the guide and remove the rear seat center shoulder belt guide.



9. REMOVE REAR SEAT SHOULDER BELT GUIDE


    B281605
  1. Remove the 2 screws.

  1. Disengage the guide and remove the rear seat shoulder belt guide LH.



10. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD


    B281607
  1. Disengage each hooks.

  1. Remove the 12 hog rings.



  1. w/ Rear Seat Side Airbag:



      B281617
    1. Remove the nut and separate the airbag bracket.



    B281609
  1. Disengage the 4 claws and remove the 2 rear seat headrest supports.

  1. w/ Seat Heater System:

    1. Disengage the clamp to disconnect the seat heater wire harness from the rear seatback frame sub-assembly LH.

  1. Remove the separate type rear seatback cover with pad from the rear seatback frame sub-assembly LH.



11. REMOVE REAR SEAT AIRBAG ASSEMBLY


    B279785
  1. Disengage the 2 clamps.

  1. Remove the 2 nuts and rear seat airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the rear seatback frame sub-assembly is not deformed. If it is, replace it with a new one.