LIGHTING SYSTEM > Turn Signal Switch Circuit |

| 1.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
Read the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Turn Signal Switch (Right) | Turn signal switch (Right) signal/ON or OFF | ON: Turn signal switch (Right) on OFF: Turn signal switch (Right) off | - |
| Turn Signal Switch (Left) | Turn signal switch (Left) signal/ON or OFF | ON: Turn signal switch (Left) on OFF: Turn signal switch (Left) off | - |
|
| ||||
| OK | ||
| ||
| 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY |
Remove the headlight dimmer switch assembly (Click here).
for LHD:
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 12 (TR) - 15 (EL) | Turn signal switch in neutral position | 10 kΩ or higher |
| 11 (TL) - 15 (EL) | Turn signal switch in neutral position | 10 kΩ or higher |
| 12 (TR) - 15 (EL) | Turn signal switch in right turn position | Below 1 Ω |
| 11 (TL) - 15 (EL) | Turn signal switch in left turn position | Below 1 Ω |
| *a | Component without harness connected (Headlight Dimmer Switch Assembly) |
for RHD:
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 20 (TR) - 16 (EL) | Turn signal switch in neutral position | 10 kΩ or higher |
| 19 (TL) - 16 (EL) | Turn signal switch in neutral position | 10 kΩ or higher |
| 20 (TR) - 16 (EL) | Turn signal switch in right turn position | Below 1 Ω |
| 19 (TL) - 16 (EL) | Turn signal switch in left turn position | Below 1 Ω |
| *a | Component without harness connected (Headlight Dimmer Switch Assembly) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY) |
Disconnect the I17 combination meter assembly connector.
for LHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I25-12 (TR) - I17-3 (ER) | Always | Below 1 Ω |
| I25-11 (TL) - I17-4 (EL) | Always | Below 1 Ω |
| I25-15 (EL) - Body ground | Always | Below 1 Ω |
| I17-3 (ER) - Body ground | Always | 10 kΩ or higher |
| I17-4 (EL) - Body ground | Always | 10 kΩ or higher |
for RHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I25-20 (TR) - I17-3 (ER) | Always | Below 1 Ω |
| I25-19 (TL) - I17-4 (EL) | Always | Below 1 Ω |
| I25-16 (EL) - Body ground | Always | Below 1 Ω |
| I17-3 (ER) - Body ground | Always | 10 kΩ or higher |
| I17-4 (EL) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||