NOISE FILTER > REMOVAL |
| 1. PRECAUTION (w/ Rear Seat Side Airbag) |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag) |
| 3. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
![]() |
Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 4. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Disengage the claw and remove the rear seat cushion lock hook.
| 5. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly LH.
| 6. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
![]() |
Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
Repeat the step above for the other hook.
w/ Seat Heater System:
Disconnect the 2 seat heater connectors.
Remove the rear seat cushion assembly.
| 7. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Disengage the claw and remove the rear seat cushion lock hook.
| 8. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 9. REMOVE REAR SEATBACK COVER (for Reclining Seat Type) |
![]() |
Disengage the 4 claws and remove the 2 rear seatback covers.
| 10. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type) |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.
Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly LH.
| 11. REMOVE REAR DOOR SCUFF PLATE LH (for Reclining Seat Type) |
![]() |
Disengage the 6 claws and remove the rear door scuff plate LH.
| 12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Reclining Seat Type) |
Disconnect the rear door opening trim weatherstrip LH.
| 13. REMOVE REAR SEAT SIDE GARNISH LH (for Reclining Seat Type) |
![]() |
Remove the bolt.
Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.
| 14. REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light) |
![]() |
Remove the bolt.
Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
![]() |
Disengage the claw and pull out the cover as shown in the illustration.
![]() |
Using a screwdriver, disengage the 6 claws and remove the 2 terminal covers with wire harness from the condenser.
![]() |
Using a screwdriver, bend back and break off the claw as shown in the illustration.
Remove the terminal cover from the wire harness.
| 15. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Window Defogger) |
| 16. REMOVE ROOF SIDE INNER GARNISH LH (for Window Defogger) |
![]() |
Disengage the 5 clips.
Disengage the guide and remove the roof side inner garnish LH.
| 17. REMOVE RADIO SETTING CONDENSER (for Window Defogger) |
![]() |
Remove the bolt.
Disengage the 2 clamps and disconnect the radio setting condenser with wire harness from the vehicle body.
![]() |
Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.
![]() |
Using a screwdriver, bend back and break off the claw as shown in the illustration.
Remove the terminal cover from the wire harness.