Home › Engine / Hybrid System ยท 2AR-FE › INTAKE / EXHAUST › EXHAUST PIPE

EXHAUST PIPE > INSTALLATION

for Preparation Click here



1. INSTALL TAIL EXHAUST PIPE BAFFLE SUB-ASSEMBLY (w/ Tail Exhaust Pipe Baffle)


    A254742E01
  1. Align the concave area of the baffle with the protruding part of the tail exhaust pipe assembly as shown in the illustration.

  1. Using a plastic hammer, uniformly tap a new tail exhaust pipe baffle sub-assembly onto the tail exhaust pipe assembly.
    Text in Illustration 
    *a
    Protruding Part
    *b
    Concave



    A254738E01
  1. Check that the concave area of the baffle is aligned with the protruding part on the bottom of the tail exhaust pipe assembly as shown in the illustration.
    Text in Illustration 
    *a
    Baffle Edge
    *b
    Concave
    *c
    Protruding Part



2. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum
    40.5 mm (1.60 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Fully insert a new gasket to the exhaust manifold converter sub-assembly.



    A181728E17
  1. Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly
    *2
    Gasket
    *3
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Connect the front exhaust pipe assembly to the exhaust pipe support.



3. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. Install a new gasket to the front exhaust pipe assembly.

  1. Connect the center exhaust pipe assembly to the exhaust pipe support.

  1. Install the center exhaust pipe assembly with the 2 nuts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



4. INSTALL TAIL EXHAUST PIPE ASSEMBLY


    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum
    38.5 mm (1.52 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Fully insert a new gasket to the center exhaust pipe assembly.



    A181728E17
  1. Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the center exhaust pipe assembly.
    Text in Illustration 
    *1
    Center Exhaust Pipe Assembly
    *2
    Gasket
    *3
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Connect the tail exhaust pipe assembly to the 3 exhaust pipe supports.

  1. Install the tail exhaust pipe assembly with the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



5. INSTALL HEATED OXYGEN SENSOR
(Click here)


6. INSPECT FOR EXHAUST GAS LEAK