BACK WINDOW GLASS > REMOVAL |
| 1. REMOVE ROOF HEADLINING ASSEMBLY |
| 2. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side) |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
| 3. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side) |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
| 4. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH |
![]() |
Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.
| 5. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.
| 6. REMOVE CENTER STOP LIGHT SET |
![]() |
Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.
![]() |
Turn the center stop light set 180 degrees as shown by the arrow in the illustration.
Disconnect the connector and remove the center stop light set.
| 7. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER |
![]() |
Using a moulding remover, disengage the 2 claws and 2 guides to remove the child restraint seat tether anchor cover.
| 8. REMOVE REAR SEAT SHOULDER BELT COVER |
![]() |
Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.
| 9. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
![]() |
Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.
| *1 | Protective Tape |
Disengage the 5 guides.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.
| 10. REMOVE BACK WINDOW GLASS SUB-ASSEMBLY |
Disconnect each connector.
![]() |
Apply protective tape to the area around the installation position of the back window glass on the vehicle body to prevent it from being scratched.
| *1 | Protective Tape |
![]() |
Pass a piano wire between the vehicle body and glass from the interior.
| *1 | Stopper |
| *2 | Piano Wire |
Tie both wire ends to wooden blocks or similar objects.
Cut off the adhesive by pulling the piano wire around the back window glass.
![]() |
Place matchmarks on the back window glass and vehicle body on the locations indicated in the illustration.
| *1 | Matchmark |
Disconnect the back window glass stoppers.

| *A | 1-piece type | *B | 2-piece type |
| *1 | No. 1 Back Window Glass Stopper | *2 | No. 2 Back Window Glass Stopper |
Using suction cups, remove the back window glass sub-assembly.
| 11. REMOVE BACK WINDOW GLASS ADHESIVE DAM |
When reusing the back window glass:
![]() |
Using a scraper, remove the back window glass adhesive dam.
| *1 | Back Side |
| 12. REMOVE BACK WINDOW OUTSIDE MOULDING |
When reusing the back window glass:
![]() |
Using a scraper, remove the back window outside moulding.
| *1 | Back Side |
| 13. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type) |
When reusing the back window glass:
![]() |
Using a scraper, remove the 2 No. 1 back window glass stoppers.
| *1 | Back Side |
| 14. REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type) |
When reusing the back window glass:
![]() |
Using a scraper, remove the 2 No. 2 back window glass stoppers.
| *1 | Back Side |
| 15. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type) |
![]() |
Remove the 2 No. 1 back window glass stoppers.
| 16. CLEAN BACK WINDOW GLASS |
Using a scraper, remove any adhesive dam and adhesive residue from the back window glass.
![]() |
Clean the outer circumference of the back window glass with a non-residue solvent.
| 17. CLEAN VEHICLE BODY |
![]() |
Clean and shape the contact surface of the vehicle body.
| *1 | Adhesive |
| *2 | Body |
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.