Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING

ROOF HEADLINING > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing.
for Separate Type Yaw Rate Sensor: (Click here)
for Built-in Type Yaw Rate Sensor: (Click here)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT DOOR SCUFF PLATE LH


    B278977
  1. Disengage the 10 claws and remove the front door scuff plate LH.



4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B278978
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



5. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the front door opening trim weatherstrip LH.



6. REMOVE FRONT PILLAR GARNISH LH


    B278985E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    HINT:
    Make the front pillar garnish LH hang down from the front pillar garnish clip.



    B278986E01
  1. While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.

  1. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.



    B278988E01
  1. Protect the curtain shield airbag assembly.
    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Protective Cover
    *3
    Curtain Shield Airbag Assembly

    1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



7. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



10. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



11. REMOVE REAR SEAT CUSHION ASSEMBLY


  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.




      B279202E01
    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
      Standard Measurement 
      a
      100 mm (3.94 in.) or less

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.



12. REMOVE REAR SEAT CUSHION LOCK HOOK


    B279203
  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the RH side and the LH side.



13. REMOVE INNER LUGGAGE COMPARTMENT TRIM PAD


    B279201
  1. Remove the inner luggage compartment trim pad.



14. REMOVE REAR SEATBACK ASSEMBLY RH


    B279206E01
  1. Disengage the 3 fasteners as shown in the illustration.
    Text in Illustration 
    *1
    Fastener



    B279208
  1. Remove the 2 bolts and rear seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



15. REMOVE REAR SEATBACK ASSEMBLY LH


    B279209E01
  1. Disengage the 2 fasteners as shown in the illustration.
    Text in Illustration 
    *1
    Fastener



    B279211
  1. Remove the 2 bolts and rear seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



16. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
  1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

  1. Disconnect the connector.



    B285009
  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear side seatback assembly RH.



17. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    B279209E01
  1. Disengage the 2 fasteners as shown in the illustration.
    Text in Illustration 
    *1
    Fastener



    B279211
  1. Remove the 2 bolts and rear seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



18. REMOVE REAR DOOR SCUFF PLATE LH


    B278979
  1. Disengage the 6 claws and remove the rear door scuff plate LH.

    HINT:
    Disengage the claws from the rear side of the scuff plate.



19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip LH.



20. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    B271081
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



21. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B271082
  1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.



22. REMOVE CENTER PILLAR LOWER GARNISH LH


    B278989
  1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.



23. REMOVE CENTER PILLAR UPPER GARNISH LH


    B278990
  1. Remove the 2 screws.

  1. Disengage the clip.

  1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.



24. REMOVE ROOF SIDE INNER GARNISH LH


    B278991
  1. Disengage the 5 clips.

  1. Disengage the guide and remove the roof side inner garnish LH.



25. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



26. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



27. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



28. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



29. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side.



30. REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:
Use the same procedure as for the LH side.



31. REMOVE ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure as for the LH side.



32. REMOVE FRONT SEAT ASSEMBLY LH
for TMMK Made Manual Seat (Click here)
for TMMK Made Power Seat (Click here)
for SIA Made Manual Seat (Click here)
for SIA Made Power Seat (Click here)


33. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



34. REMOVE INSTRUMENT PANEL ASSEMBLY
(Click here)


35. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    B279249
  1. Disengage the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow shown in the illustration.



    B279250
  1. Disengage the 6 claws and remove the inner rear view mirror stay holder cover.



36. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)


    E226707
  1. Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the roof console box assembly.



37. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)


    E226709
  1. Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the roof console box assembly.



38. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)


    E228309E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.
    Text in Illustration 
    *1
    Protective Tape
    *a
    Front



    E228310E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws as shown in the illustration and remove the No. 1 room light housing.
    Text in Illustration 
    *1
    Protective Tape
    *a
    Front



    E220648E02
  1. Using a screwdriver, disengage the 4 claws and disconnect the room light switch base from the No. 1 room light housing.
    Text in Illustration 
    *1
    Room Light Switch Base



39. REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)


    E227560E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 8 claws and remove the 2 spot light lenses.
    Text in Illustration 
    *1
    Protective Tape
    *a
    Front



    E227562E01
  1. Using a screwdriver with its tip wrapped with protective tape and moulding remover, disengage the 2 claws <A>.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Claw <A>
    *3
    Claw <B>
    *4
    Claw <C>
    *a
    Front

  1. Disengage the 2 claws <B> and 2 claws <C>, and disconnect the spot light housing.



    E227564E01
  1. Using a screwdriver, disengage the 8 claws and disconnect the 2 map light sub-assemblies from the spot light housing.
    Text in Illustration 
    *1
    Map Light Sub-assembly



40. REMOVE ASSIST GRIP SUB-ASSEMBLY


    B278995E01
  1. Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    Tape the screwdriver tip before use.



    B278999
  1. Disengage the 2 clips and remove the assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side.



41. REMOVE REAR ASSIST GRIP ASSEMBLY LH


    B278997E01
  1. Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    Tape the screwdriver tip before use.



    B279000
  1. Disengage the 2 clips and remove the rear assist grip assembly LH.

  1. Remove the 2 clips from the vehicle body.



42. REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



43. REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
  1. Remove the sliding roof opening trim moulding.



44. REMOVE VISOR BRACKET COVER (for LH Side)


    B278992
  1. Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.



45. REMOVE VISOR ASSEMBLY LH


    B278994
  1. Remove the 2 screws and visor assembly LH.



46. REMOVE VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



47. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



48. REMOVE VISOR HOLDER


    B211697E01
  1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    HINT:
    Use the same procedure for the other visor holder.



49. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
  1. w/ EC Mirror

    1. Disconnect the connector from the inner rear view mirror.



  1. Remove the bolt and disconnect the bracket from the front pillar RH.


    B279005E01


    Text in Illustration 
    *A
    w/o Satellite Radio
    *B
    w/ Satellite Radio

  1. Disengage the 3 clamps from the front pillar RH.

  1. Disengage the 4 clamps from the front pillar LH.

  1. w/o Satellite Radio:

    1. Disengage the 2 clamps and disconnect the connector from the rear pillar RH.

  1. w/ Satellite Radio:

    1. Disengage the 2 clamps and disconnect the 2 connectors from the rear pillar RH.

  1. Remove the 2 clips.

  1. Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

    HINT:
    Leave the 2 clips in the vehicle.



    B279009
  1. Remove the roof headlining assembly from the vehicle through the front door RH.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.



    B279104
  1. Remove the 2 clips from the vehicle body as shown in the illustration.



50. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
  1. w/ EC Mirror

    1. Disconnect the connector from the inner rear view mirror.



  1. Disconnect the connector from the sliding roof drive gear assembly.


    B279007E01


    Text in Illustration 
    *A
    w/o Satellite Radio
    *B
    w/ Satellite Radio

  1. Remove the bolt and disconnect the bracket from the front pillar RH.

  1. Disengage the 3 clamps from the front pillar RH.

  1. Disengage the 4 clamps from the front pillar LH.

  1. w/o Satellite Radio:

    1. Disengage the 2 clamps and disconnect the connector from the rear pillar RH.

  1. w/ Satellite Radio:

    1. Disengage the 2 clamps and disconnect the 2 connectors from the rear pillar RH.

  1. Remove the 2 clips.

  1. Disengage the 2 fasteners.

  1. Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

    HINT:
    Leave the 2 clips in the vehicle.



    B279010
  1. Remove the roof headlining assembly from the vehicle through the front door RH.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.



    B279104
  1. Remove the 2 clips from the vehicle body as shown in the illustration.