ENGINE IMMOBILISER SYSTEM (w/ Smart Key System) > REGISTRATION |
| 1. DESCRIPTION OF CODE REGISTRATION |
![]() |
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
| 2. KEY REGISTRATION PROCEDURES WHEN ADDING OR REPLACING KEY OR WHEN KEY IS LOST |
| Customer Request/Condition | Registration Procedure Condition | Procedure | Refer to |
| Registering additional key | Customer must bring at least 1 key | 1. Register additional keys as necessary (additional key ID registration) | PROCEDURE "C" |
| Customer must bring at least 1 key | 1. Using remaining key, clear all registered keys except one (key ID erasure) | PROCEDURE "D" |
| 2. Register additional keys as necessary (additional key ID registration) | PROCEDURE "C" | ||
| All keys are lost | - | 1. Reset all keys (all keys ID erasure (key code reset)) | PROCEDURE "E" |
| 2. Register all keys (new key ID registration) | PROCEDURE "A" |
| 3. PART REPLACEMENT AND KEY REGISTRATION PROCEDURES |
If a malfunctioning ECU is discovered through troubleshooting of the smart key system, use the ECU replacement and key registration procedures in the table below.
| Malfunctioning ECU | Condition | Procedure | Refer to | |
| Certification ECU (smart key ECU assembly) | Customer has brought all keys | 1. Replace certification ECU (smart key ECU assembly) | - | |
| 2. Reregister all customer's keys | PROCEDURE "B"*1 | |||
| 3. ECU communication ID registration | PROCEDURE "G"*1 | |||
| 4. Remote engine starter ID registration*2 |
Click here
| |||
| Some keys are lost | Key ID codes can be registered and cleared | 1. Clear key codes (key ID erasure) | PROCEDURE "D" | |
2. Perform additional key registration procedure (additional key ID registration)
| PROCEDURE "C"*1 | |||
| 3. Replace certification ECU (smart key ECU assembly) | - | |||
| 4. Reregister all keys | PROCEDURE "B" | |||
| 5. ECU communication ID registration | PROCEDURE "G" | |||
| 6. Remote engine starter ID registration*2 |
Click here
| |||
| Key ID codes cannot be either registered or cleared | 1. Replace certification ECU (smart key ECU assembly) | - | ||
| 2. Replace steering lock ECU (steering lock actuator assembly) | - | |||
3. Reregister all keys (new key ID registration)
| PROCEDURE "A" | |||
| 4. ECU communication ID registration | PROCEDURE "G" | |||
| 5. Remote engine starter ID registration*2 |
Click here
| |||
| Certification ECU (smart key ECU assembly) | All keys are lost | 1. Replace certification ECU (smart key ECU assembly) | - | |
| 2. Replace steering lock ECU (steering lock actuator assembly) | - | |||
| 3. Register all keys (new key ID registration) | PROCEDURE "A" | |||
| 4. ECU communication ID registration | PROCEDURE "G" | |||
| 5. Remote engine starter ID registration*2 |
Click here
| |||
| Steering lock ECU (steering lock actuator assembly) | Customer has brought at least 1 key | 1. Replace steering lock ECU (steering lock actuator assembly) | - | |
| 2. Register recognition codes in ECUs (ECU code registration) | PROCEDURE "F" | |||
| All keys are lost | 1. Replace certification ECU (smart key ECU assembly) | - | ||
| 2. Replace steering lock ECU (steering lock actuator assembly) | - | |||
| 3. Register all keys (new key ID registration) | PROCEDURE "A" | |||
| 4. ECU communication ID registration | PROCEDURE "G" | |||
| 5. Remote engine starter ID registration*2 |
Click here
| |||
| 4. KEY REGISTRATION (PROCEDURE "A") |
New key ID registration:
| Process | Procedure |
| 1. Start of registration |
|
| 2. Confirmation of ECU code |
|
| 3. Verification of unregistered key* |
|
| 4. Registration of ID code |
|
| 5. End of registration |
|
| 5. KEY REGISTRATION (PROCEDURE "B") |
New key ID registration:
| Process | Procedure |
| 1. Start of registration |
|
| 2. Confirmation of ECU code |
|
| 3. Confirmation of all registered keys*1 |
|
| 4. Confirmation of ECU code |
|
| 5. Verification of unregistered key*2 |
|
| 6. Registration of ID code |
|
| 7. End of registration |
|
| 6. KEY REGISTRATION (PROCEDURE "C") |
Additional key ID registration:
| Process | Procedure |
| 1. Start of registration |
|
| 2. Confirmation of registered key*1 |
|
| 3. Confirmation of ECU code |
|
| 4. Verification of unregistered key*2 |
|
| 5. Registration of ID code |
|
| 6. End of registration |
|
| 7. KEY REGISTRATION (PROCEDURE "D") |
Key ID erasure:
| Process | Procedure |
| 1. Start of erasure |
|
| 2. Confirmation of registered key* |
|
| 3. Confirmation of ECU code |
|
| 4. Erasure of ID code |
|
| 5. End of erasure |
|
| 8. KEY REGISTRATION (PROCEDURE "E") |
All keys ID erasure:
| Process | Procedure |
| 1. Start of erasure |
|
| 2. Confirmation of ECU code |
|
| 3. Erasure of ID code |
|
| 4. End of erasure |
|
| 9. KEY REGISTRATION (PROCEDURE "F") |
ECU code registration:
| Process | Procedure |
| 1. Start of registration |
|
| 2. Confirmation of registered key* |
|
| 3. Erasure of ECU code |
|
| 4. End of registration |
|
| 10. KEY REGISTRATION (PROCEDURE "G") |
ECU communication ID registration:
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the engine switch on (IG) (do not start the engine) and leave it as is for 30 minutes.
Turn the engine switch off and disconnect terminals 13 (TC) and 4 (CG).
Check that the engine starts and stays on for more than 3 seconds.