Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
  1. In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
  2. The actual values may differ from the values listed in the chart under "Results of real-vehicle check" due to climate, weather conditions, etc.

HINT:
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.

  1. Warm up the engine.

  2. Turn the A/C switch off.

  3. Turn the ignition switch off.

  4. Connect the Techstream to the DLC3.

  5. Turn the ignition switch to ON.

  6. Turn the Techstream on.

  7. Enter the following menus: Powertrain / Engine and ECT / Data List.

    HINT:
    1. To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
    2. When you select a measurement group, the ECU data belonging to that group is displayed.
    3. Measurement Group List / Description
      1. All Data / All data
      2. Primary / -
      3. Engine Control / Engine control system related data
      4. Gas General / -
      5. Gas AF Control / Air fuel ratio control system related data
      6. Gas AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data
      7. Gas Throttle / Gasoline throttle system related data
      8. Gas Intake Control / Intake control system related data
      9. Gas Valve Control / Valve control system related data
      10. Gas Misfire / "Misfire" related data
      11. Gas Starting / "Difficult to start" related data
      12. Gas Rough Idle / "Rough idle" related data
      13. Gas Evaporative / Evaporative system related data
      14. Gas CAT Converter / Catalyst converter related data
      15. Check Mode / Check mode related data
      16. Monitor Status / Monitor status related data
      17. Ignition / Ignition system related data
      18. Charging Control / Charging control system related data
      19. Compression / Data used during "Check the Cylinder Compression" Active Test
      20. AT / Automatic transaxle system related data
      21. Vehicle Information / Vehicle information

  8. According to the display on the Techstream, read the Data List.

    HINT:
    1. The title used for each group of Data List items in this repair manual does not appear on the Techstream. However, the name in parentheses after the title, which is a Measurement Group, does appear on the Techstream. When the name shown in parentheses is selected on the Techstream, all the Data List items listed for that group will be displayed.
    2. "Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.


Various Vehicle Conditions 1 (All Data)

Vehicle Speed 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Actual vehicle speed
Yes
Diagnostic Note:
  1. This is the current vehicle speed.
  2. The vehicle speed is detected using the wheel speed sensors.
    1. Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.

Engine Speed 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
610 to 710 rpm: Idling
Yes
Results of real-vehicle check:
Idling (engine warmed up and A/C off): 660 rpm
Diagnostic Note:
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

Calculate Load 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Calculate Load
Load calculated by ECM/
Min.: 0%, Max.: 100%
-
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 0.0%
  2. Idling (engine warmed up): 28.2%
  3. Running without load (3000 rpm): 26.2%
Diagnostic Note:
This is the engine load calculated based on the estimated intake manifold pressure.
Calculate Load = Estimated intake manifold pressure / maximum intake manifold pressure x 100 (%)
(For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.)

Vehicle Load 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vehicle Load
Vehicle load/
Min.: 0%, Max.: 25700%
-
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 0.0%
  2. Idling (engine warmed up): 15.2%
  3. Running without load (3000 rpm): 14.9%
Diagnostic Note:
This is the engine intake air charging efficiency.
Vehicle Load = Current intake airflow (g/rev.) / maximum intake airflow
Maximum intake airflow = Displacement (L) / 2 x 1.2 (g/rev.)

HINT:
Due to individual engine differences, intake air temperature, etc., the value may exceed 100%.
Intake airflow (g/rev.) = Intake airflow (gm/sec) x 60 / Engine speed (rpm)
(Intake airflow (gm/sec) is MAF)


MAF 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MAF
Airflow rate from mass air flow meter sub-assembly/
Min.: 0 gm/sec, Max.: 655.35 gm/sec
1.0 to 3.0 gm/sec: Idling
8 to 22 gm/sec: 3000 rpm (without load)
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 0.42 gm/sec
  2. Idling (engine warmed up): 2.54 gm/sec
  3. Running without load (2500 rpm): 9.37 gm/sec
  4. Running without load (3000 rpm): 11.17 gm/sec
Diagnostic Note:
This is the intake air amount from the mass air flow meter sub-assembly.

Atmosphere Pressure 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Atmosphere Pressure
Atmospheric pressure/
Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1912 mmHg)
Equivalent to atmospheric pressure (absolute pressure)
Yes
Results of real-vehicle check:
Idling (engine warmed up): 100 kPa(abs) [750 mmHg(abs)]
Diagnostic Note:
  1. This value is calculated from the intake air amount.
  2. Standard atmospheric pressure: 101 kPa(abs) [760 mmHg(abs)]
  3. For every 100 m (328 ft) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather.

Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Coolant Temp
Coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up
Yes
Diagnostic Note:
This is the engine coolant temperature.

HINT:
  1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
  2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
  3. If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.
  4. Check if the engine overheats when the value indicates higher than 135°C (275°F).


Intake Air 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Intake Air
Intake air temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
Equivalent to temperature at location of mass air flow meter sub-assembly
Yes
Diagnostic Note:
  1. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
  2. If the value is -40°C (-40°F), or higher than 128°C (262°F), the sensor circuit is open or shorted.

Engine Run Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Run Time
Engine run time/
Min.: 0 s, Max.: 65535 s
Time after engine start
Yes
Diagnostic Note:
This is the time elapsed since the engine started.

HINT:
The time is counted only while the engine is running.


Initial Engine Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C (-40°F), Max.: 119.3°C (247°F)
-
Yes
Diagnostic Note:
This is the coolant temperature stored when the ignition switch is turned to ON.

Initial Intake Air Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C (-40°F), Max.: 119.3°C (247°F)
-
Yes
Diagnostic Note:
This is the intake air temperature stored when the ignition switch is turned to ON.

Battery Voltage 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 14 V: Idling
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 11.679 V
  2. Cranking: 11.523 V
  3. Idling (engine warmed up): 13.457 V
Diagnostic Note:
If 11 V or less, characteristics of some electrical components may change.

Glow Indicator Supported 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Glow Indicator Supported
Status of the glow indicator supported/
Unsupported or Supported
Unsupported
Yes

Glow Indicator 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Glow Indicator
Status of the glow indicator/
ON or OFF
OFF
Yes

Throttle Control 1 (Gas Throttle)

Accelerator Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accelerator Position
Accelerator pedal position/
Min.: 0%, Max.: 399.9%
Actual accelerator pedal position
No
Results of real-vehicle check:
  1. Ignition switch ON: 0.0% (accelerator pedal fully released)
  2. Ignition switch ON: 100.0% (accelerator pedal fully depressed)
Diagnostic Note:
This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%.

Accel Sens. No.1 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sens. No.1 Volt %
Absolute accelerator pedal position No. 1/
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal fully released
52 to 90%: Accelerator pedal fully depressed
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 15.6% (accelerator pedal fully released)
  2. Ignition switch ON: 70.9% (accelerator pedal fully depressed)
Diagnostic Note:
The accelerator pedal position sensor No. 1 output is converted using 5 V = 100%.

HINT:
If there are no accelerator pedal position sensor DTCs stored, it is possible to conclude that the accelerator pedal position sensor system is normal.


Accel Sens. No.2 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sens. No.2 Volt %
Absolute accelerator pedal position No. 2/
Min.: 0%, Max.: 100%
24 to 40%: Accelerator pedal fully released
68 to 99%: Accelerator pedal fully depressed
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 31.7% (accelerator pedal fully released)
  2. Ignition switch ON: 87.8% (accelerator pedal fully depressed)
Diagnostic Note:
The accelerator pedal position sensor No. 2 output is converted using 5 V = 100%.

Throttle Control 2 (All Data)

Accel Sensor Out No.1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sensor Out No.1
Accelerator pedal position sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Accelerator pedal fully released
2.6 to 4.5 V: Accelerator pedal fully depressed
No
Results of real-vehicle check:
  1. Ignition switch ON: 0.781 V (accelerator pedal fully released)
  2. Ignition switch ON: 3.535 V (accelerator pedal fully depressed)
Diagnostic Note:
This is the raw voltage from the accelerator pedal position sensor No. 1.

Accel Sensor Out No.2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sensor Out No.2
Accelerator pedal position sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V
1.2 to 2.0 V: Accelerator pedal fully released
3.4 to 4.98 V: Accelerator pedal fully depressed
No
Results of real-vehicle check:
  1. Ignition switch ON: 1.582 V (accelerator pedal fully released)
  2. Ignition switch ON: 4.375 V (accelerator pedal fully depressed)
Diagnostic Note:
This is the raw voltage from the accelerator pedal position sensor No. 2.
Accelerator pedal position sensor No. 2 is used to monitor accelerator pedal position sensor No. 1. When there is a malfunction in sensor No. 1, the ECM uses sensor No. 2 to control the engine.

Throttle Control 3 (Gas Throttle)

Accelerator Idle Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting released accelerator pedal/
ON or OFF
ON: Accelerator pedal fully released
No
Results of real-vehicle check:
  1. Ignition switch ON: ON (accelerator pedal fully released)
  2. Ignition switch ON: OFF (accelerator pedal depressed)
Diagnostic Note:
This is a parameter calculated by the ECM which indicates whether the accelerator pedal is in the learned idle position.

Accel Fully Close Learn #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Fully Close Learn #1
Accelerator fully released learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg
-
No
Results of real-vehicle check:
Ignition switch ON: 19.5 deg
Diagnostic Note:
This is the value of accelerator pedal position sensor No. 1 learned when the accelerator pedal is released.

Accel Fully Close Learn #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Fully Close Learn #2
Accelerator fully released learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg
-
No
Results of real-vehicle check:
Ignition switch ON: 39.5 deg
Diagnostic Note:
This is the value of accelerator pedal position sensor No. 2 learned when the accelerator pedal is released.

Throttle Sensor Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sensor Volt %
Absolute throttle position sensor No. 1/
Min.: 0%, Max.: 100%
  1. 10 to 22%: Accelerator pedal fully released
  2. 64 to 96%: Accelerator pedal fully depressed
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 18.4% (accelerator pedal fully released)

    HINT:
    The throttle valve is not completely closed, but is kept open a certain amount by the throttle valve opener.

  2. Ignition switch ON: 82.3% (accelerator pedal fully depressed)
  3. Idling (engine warmed up): 14.9%
  4. Running without load (3000 rpm): 19.2%
Diagnostic Note:
The throttle position sensor No. 1 output is converted using 5 V = 100%.

HINT:
If there are no throttle position sensor DTCs stored, it is possible to conclude that the throttle position sensor system is normal.


Throttl Sensor #2 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttl Sensor #2 Volt %
Throttle sensor position No. 2/
Min.: 0%, Max.: 100%
  1. 42 to 62%: Accelerator pedal fully released
  2. 92 to 100%: Accelerator pedal fully depressed
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 50.5% (accelerator pedal fully released)

    HINT:
    The throttle valve is not completely closed, but is kept open a certain amount by the throttle valve opener.

  2. Ignition switch ON: 99.2% (accelerator pedal fully depressed)
  3. Idling (engine warmed up): 46.6%
Diagnostic Note:
The throttle position sensor No. 2 output is converted using 5 V = 100%.

ST1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ST1
Brake pedal signal/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal fully released
No
Diagnostic Note:
This is the stop light switch assembly signal (ST1- terminal).

System Guard 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
System Guard
System guard/
ON or OFF
ON
No
Results of real-vehicle check:
Idling (engine warmed up): ON
Diagnostic Note:
When there is a difference between the target and actual throttle valve opening angles, system guard turns off and stops the electronic throttle control system function.
OFF: Electronic throttle control is stopped.

Open Side Malfunction 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Open Side Malfunction
Open malfunction/
ON or OFF
OFF
No
Diagnostic Note:
This parameter indicates a malfunction in the electronic throttle when the throttle valve is open.

Throttle Idle Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Idle Position
Whether or not throttle position sensor detecting idle/
ON or OFF
-
No
Results of real-vehicle check:
  1. Ignition switch ON: ON

    HINT:
    The throttle valve is not completely closed, but is kept open a certain amount by the throttle valve opener.

  2. Idling (engine warmed up): ON
  3. Running without load (3000 rpm): OFF
Diagnostic Note:
This is a parameter calculated by the ECM.
The value is ON when the throttle is at the idle position and OFF when the throttle is open.

Throttle Require Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Require Position
Required throttle position/
Min.: 0 V, Max.: 4.98 V
-
No
Results of real-vehicle check:
  1. Ignition switch ON: 0.82 V (accelerator pedal fully released)
  2. Ignition switch ON: 4.10 V (accelerator pedal fully depressed)
  3. Idling (engine warmed up): 0.72 V
Diagnostic Note:
This is a value calculated by the ECM showing the voltage for the target throttle valve position. It is almost an exact match of the Throttle Position No. 1 value except during very rapid throttle valve movement, such as that used during wheelspin control.

Throttle Sensor Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sensor Position
Throttle sensor position/
Min.: 0%, Max.: 100%
  1. 0%: Accelerator pedal fully released
  2. 50 to 80%: Accelerator pedal fully depressed
Yes
Results of real-vehicle check:
Idling (engine warmed up): 0.0%
Diagnostic Note:
This is the throttle valve opening amount used for engine control.
(100% signifies 125° of throttle valve rotation. This does not include the amount the throttle valve is opened to maintain the idle speed during idling.)
This value has no meaning when the ignition switch is ON and the engine is stopped.
The throttle valve opening amount during idling is indicated by 0%. When the throttle valve is fully open, the value is 68%.

Throttle Position No. 1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position No. 1
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
Almost same as "Throttle Require Position"
  1. 0.5 to 1.1 V: Accelerator pedal fully released
  2. 3.2 to 4.8 V: Accelerator pedal fully depressed
  3. 0.6 to 1.4 V: Fail-safe operating
No
Results of real-vehicle check:
  1. Ignition switch ON: 0.82 V (accelerator pedal fully released)
  2. Ignition switch ON: 4.10 V (accelerator pedal fully depressed)
  3. Idling (engine warmed up): 0.72 V
Diagnostic Note:
This is the throttle position sensor No. 1 output voltage.

Throttle Position No. 2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position No. 2
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
  1. 2.1 to 3.1 V: Accelerator pedal fully released
  2. 4.6 to 4.98 V: Accelerator pedal fully depressed
  3. 2.1 to 3.1 V: Fail-safe operating
No
Results of real-vehicle check:
  1. Ignition switch ON: 2.42 V (accelerator pedal fully released)
  2. Ignition switch ON: 4.94 V (accelerator pedal fully depressed)
  3. Idling (engine warmed up): 2.30 V
Diagnostic Note:
This is the throttle position sensor No. 2 output voltage.

Throttle Position Command 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.98 V
-
No
Diagnostic Note:
Throttle Position Command is the same value as Throttle Require Position.

Throttle Sens Open Pos #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sens Open Pos #1
Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V
0.6 to 1.4 V
No
Results of real-vehicle check:
Ignition switch ON: 0.917 V
Diagnostic Note:
This is the throttle position sensor No. 1 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch ON.

Throttle Sens Open Pos #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sens Open Pos #2
Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.98 V
1.7 to 2.5 V
No
Results of real-vehicle check:
Ignition switch ON: 2.01 V
Diagnostic Note:
This is the throttle position sensor No. 2 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch ON.

Throttle Motor Current 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor Current
Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling
No
Results of real-vehicle check:
  1. Ignition switch ON: 0.7 A (accelerator pedal fully released)
  2. Ignition switch ON: 0.8 A (accelerator pedal fully depressed)
  3. Idling (engine warmed up): 0.7 A
  4. Running without load (3000 rpm): 0.7 A
Diagnostic Note:
  1. When this value is large but the actual opening angle (Throttle Position No. 1) does not reach the target opening angle (Throttle Require Position), there is an "unable to open" malfunction.
  2. This value normally fluctuates around 1 A.

Throttle Motor DUTY 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor DUTY
Throttle actuator/
Min.: 0%, Max.: 100%
10 to 22%: Idling
Yes
Diagnostic Note:
This is the output duty ratio of the throttle actuator drive circuit.

Throttle Motor Duty (Open) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
No
Results of real-vehicle check:
  1. Ignition switch ON: 0% (accelerator pedal fully released)
  2. Ignition switch ON: 16% (accelerator pedal fully depressed)
  3. Idling (engine warmed up): 0%
  4. Running without load (3000 rpm): 10%
Diagnostic Note:
  1. This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal.
  2. When the throttle valve is being opened, Throttle Motor Duty (Open) is 10 to 50%.

Throttle Motor Duty (Close) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor Duty (Close)
Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
No
Results of real-vehicle check:
  1. Ignition switch ON: 12% (accelerator pedal fully released)
  2. Ignition switch ON: 0% (accelerator pedal fully depressed)
  3. Idling (engine warmed up): 12%
  4. Running without load (3000 rpm): 0%
Diagnostic Note:
This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.

HINT:
During idling, the throttle valve opening angle is usually controlled using a duty ratio drive signal which closes the throttle valve. However, when carbon deposits build up, it may be necessary to open the throttle valve more than the throttle valve opener does. In that case, the opening angle is controlled using a "Throttle Motor Duty (Open)" signal which opens the throttle valve.


Throttle Fully Close Learn 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Fully Close Learn
Throttle valve fully closed position (learned value)/
Min.: 0 V, Max.: 4.98 V
0.4 to 1.0 V: Accelerator pedal fully released
No
Results of real-vehicle check:
Ignition switch ON: 0.625 V
Diagnostic Note:
  1. The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. This learned value is calculated by the ECM with the throttle valve opener angle (approximately 4 to 7°, the position when the ignition switch is ON, the accelerator pedal is released and the throttle actuator is off).
  2. Learning is performed immediately after the ignition switch is turned to ON.

+BM Voltage 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
+BM Voltage
+BM voltage/
Min.: 0 V, Max.: 79.998 V
11 to 14 V: Ignition switch ON and system normal
No
Diagnostic Note:
This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P2118 (open circuit) and P0657 (short circuit, ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the ignition switch is turned off).

Actuator Power Supply 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Actuator Power Supply
Actuator power supply/
ON or OFF
ON: Idling
No
Diagnostic Note:
If +BM power is lost, this item changes to OFF.

Throttle Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position
Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
-
Yes
Results of real-vehicle check:
Idling (engine warmed up): 0.00 deg
Diagnostic Note:
This value has no meaning when the ignition switch is ON and the engine is stopped.

Idle Speed Control (Gas Rough Idle)

ISC Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Flow
Flow rate calculated using information from mass air flow meter sub-assembly/
Min.: 0 L/s, Max.: 79.99 L/s
-
Yes
Results of real-vehicle check:
Idling (engine warmed up): 1.80 L/s
Diagnostic Note:
This is the total ISC airflow amount (the amount of intake air necessary to maintain idling).

HINT:
ISC Flow (total ISC airflow amount) = ISC Learning Value + ISC Feedback Value + each compensation amount


ISC Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Position
Requested throttle opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
-
Yes
Results of real-vehicle check:
Idling (engine warmed up): 2.55 deg
Diagnostic Note:
This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).

ISC Feedback Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Feedback Value
ISC feedback amount/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Results of real-vehicle check:
Idling (engine warmed up): -0.08 L/s
Diagnostic Note:
This is the feedback amount necessary to adjust the airflow amount to maintain the target idle speed.

HINT:
When the idle speed differs from the target, the feedback amount is adjusted. If the feedback amount becomes more than a certain value, this will be reflected in the ISC learned airflow value.


ISC Learning Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Learning Value
ISC learned airflow value/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Results of real-vehicle check:
Idling (engine warmed up): 1.57 L/s
Diagnostic Note:
This is the learned value of the airflow amount necessary for engine idling.

HINT:
  1. If ISC Feedback Value becomes more than a certain value, this will be reflected in ISC Learning Value.
  2. ISC Flow (total ISC airflow amount) = ISC Learning Value + ISC Feedback Value + each compensation amount


Electric Load Feedback Val 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electric Load Feedback Val
Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Results of real-vehicle check:
Idling (headlights and window defogger on): 0.43 L/s
Diagnostic Note:
This is the ISC compensation amount determined according to the electrical load.

Air Conditioner FB Val 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Air Conditioner FB Val
Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Results of real-vehicle check:
Idling (A/C on): 0.66 L/s
Diagnostic Note:
This is the ISC compensation amount determined according to the air conditioner load.

Low Revolution Control 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Low Revolution Control
Low engine speed control operation state/
ON or OFF
-
Yes
Results of real-vehicle check:
Idling (engine warmed up): OFF
Diagnostic Note:
  1. This parameter indicates whether the engine speed dropped immediately after starting due to poor combustion, etc. This parameter changes to ON when the engine speed drops to below the following speeds 1 to 7 seconds after the engine is started (when the A/C is on, the engine speed thresholds below increase by 100 to 200 rpm).
    1. 900 rpm (when the engine coolant temperature is 10°C (50°F)).
    1. 850 rpm (when the engine coolant temperature is 30°C (86°F)).
    1. 750 rpm (when the engine coolant temperature is 60°C (140°F)).
      Before 5 seconds elapse after starting the engine, this parameter indicates the status of the previous trip.
      After 5 seconds elapse after starting the engine, this parameter indicates the status of the current trip.

      HINT:
      The engine is considered to have started when the engine speed reaches 400 rpm. When the engine speed decreases immediately after starting the engine, this parameter changes to ON and remains ON for the rest of the trip.
      ON: The engine speed decreased immediately after starting the engine.
      OFF: The engine speed did not decrease immediately after starting the engine.

  2. For use when engine stall, starting problems or rough idle is present.

N Range Status 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
N Range Status
Shift lever N status/
ON or OFF
-
Yes

Eng Stall Control FB Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Eng Stall Control FB Flow
Intake air compensation flow rate/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Results of real-vehicle check:
Idling (engine warmed up): 0.00 L/s
Diagnostic Note:
  1. The intake air amount and ignition timing are adjusted when there is a large decrease in engine speed (for example, a decrease to 550 rpm or less) in order to prevent engine stall.
  2. For use when engine stall, starting problems or rough idle is present.

Deposit Loss Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Deposit Loss Flow
Flow loss due to deposits/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Results of real-vehicle check:
Idling (engine warmed up): 0.00 L/s
Diagnostic Note:
  1. This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.
  2. Check this value for reference when the engine stalls, is difficult to start, or idles roughly.
  3. When the ISC learned value is initialized, performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.
    1. Start the engine cold and allow the engine to idle.
    2. After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.
    3. Turn the ignition switch off and wait for 30 seconds.
    4. Start the engine again, and allow the engine to idle for 5 minutes.

Fuel System 1 (Gas General)

Injector (Port) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injector (Port)
Injection period of the No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
-
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 2332 μs
  2. Running without load (3000 rpm): 2293 μs
Diagnostic Note:
This is the injection period of the No. 1 cylinder (the command value from the ECM).

Injection Volum (Cylinder 1) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injection Volum (Cylinder 1)
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.5 ml
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 0.108 ml
  2. Running without load (3000 rpm): 0.097 ml
Diagnostic Note:
This is the fuel injection volume for 10 injections.

Fuel Pump/Speed Status 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Pump/Speed Status
Fuel pump status/
ON or OFF
ON: Starter on or engine running
Yes

EVAP System 1 (All Data)

Vacuum Pump 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vacuum Pump
Key-off EVAP system leak detection pump status/
ON or OFF
-
Yes
Diagnostic Note:
This item changes to ON during the key-off EVAP monitor which is performed approximately 5 hours after the ignition switch is turned off (Click here).

Intake Control 1 (Gas Intake Control)

TCV Status 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
TCV Status
Intake air control valve actuator for tumble control valve status/
ON or OFF
ON: Cold engine start
Yes
Diagnostic Note:
This item changes to ON while the tumble control valve is closed.

Fuel System 2 (Gas General)

Current Fuel Type 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Current Fuel Type
Current fuel type
Gasoline/petrol
No

EVAP System 2 (Gas Evaporative)

EVAP (Purge) VSV 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
EVAP (Purge) VSV
Purge VSV control duty/
Min.: 0%, Max.: 100%
-
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 0.0%
  2. Running without load (3000 rpm): 30.5%
Diagnostic Note:
  1. This is the command signal from the ECM.
  2. This is the purge VSV control duty ratio. When EVAP (Purge) VSV is any value except 0%, EVAP purge* is being performed.
    *: Gasoline vapor from the fuel tank is being introduced into the intake system via the purge VSV.
  3. When the engine is cold or immediately after the engine is started, EVAP (Purge) VSV is 0%.

Evap Purge Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Evap Purge Flow
Purge flow/
Min.: 0%, Max.: 399.9%
-
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 0.0%
  2. Running without load (3000 rpm): 2.5%
Diagnostic Note:
This is the percentage of total engine airflow contributed by EVAP purge operation.
(Evap Purge Flow = Purge flow / Engine airflow x 100 (%))
It is based on MAF and a stored value for airflow and controlled by adjusting the duty cycle for the purge VSV.

Purge Density Learn Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Purge Density Learn Value
Purge density learned value/
Min.: -200, Max.: 199.993
-
Yes
Results of real-vehicle check:
Idling (engine warmed up): 0.00
Diagnostic Note:
Purge Density Learn Value is the proportion of the decrease in injection volume (based on the change in the air fuel ratio feedback compensation value) related to a 1% purge flow rate.
When Purge Density Learn Value is a large negative value, the purge effect is large.
The purge density is determined from the change in the air fuel ratio feedback compensation value when purge flow is introduced.
Purge density learning is performed so that the feedback compensation value is 0 +/-2%.

HINT:
  1. Usually, the value is approximately +/-1%.
  2. 1%: The concentration of HC in the purge gas is relatively low.
  3. 0%: The concentration of HC in the purge gas is approximately equal to the stoichiometric air fuel ratio.
  4. Large negative values indicate that the concentration of HC in the purge gas is relatively high.


Vapor Pressure Pump 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vapor Pressure Pump
Vapor pressure/
Min.: 0 kPa (0 mmHg), Max.: 1441.77 kPa (10814.17 mmHg)
Approximately 100 kPa(abs) [750 mmHg(abs)]: Ignition switch ON
No
Diagnostic Note:
This is the EVAP system pressure monitored by the canister pressure sensor.

HINT:
  1. Except for when the monitor is running, this value should be approximately the same as atmospheric pressure.
  2. As Vapor Pressure Pump is almost the same as atmospheric pressure when the engine is stopped, this item can be used to help determine if the canister pressure sensor characteristics are abnormal, if there is noise, or if the sensor output is stuck at a certain value.


Vapor Pressure (Calculated) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vapor Pressure (Calculated)
Calculated EVAP system pressure/
Min.: -720.896 kPa (-5407.167 mmHg), Max.: 720.874 kPa (5407.002 mmHg)
Approximately 100 kPa(abs) [750 mmHg(abs)]: Ignition switch ON
No

EVAP System Vent Valve 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
EVAP System Vent Valve
Key-off EVAP system vent valve status/
ON or OFF
OFF: Vent
ON: Closed
Yes

EVAP Purge VSV 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
-
Yes
Diagnostic Note:
This parameter displays ON when EVAP (Purge) VSV is 30% or higher, and displays OFF when the VSV duty ratio is less than 30%.

Purge Cut VSV Duty 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Purge Cut VSV Duty
Purge VSV duty/
Min.: 0%, Max.: 399.9%
-
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 0.0%
  2. Running without load (3000 rpm): 29%

Air Fuel Ratio Control 1 (All Data)

Target Air-Fuel Ratio 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Target Air-Fuel Ratio
Target air fuel ratio/
Min.: 0, Max.: 1.99
0.8 to 1.2: During idling
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 0.999 (Performing feedback control at the stoichiometric air fuel ratio)
  2. Running without load (3000 rpm): 0.999 (Performing feedback control at the stoichiometric air fuel ratio)
Diagnostic Note:
This is the target air fuel ratio used by the ECM.
  1. 1.0 is the stoichiometric air fuel ratio. Values that are more than 1 indicate the system attempting to make the air fuel ratio leaner. Values that are less than 1 indicate the system attempting to make the air fuel ratio richer.
  2. Target Air-Fuel Ratio and AF Lambda B1S1 are related.

Air Fuel Ratio Control 2 (Gas AF O2 Sensor)

AF Lambda B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
AF Lambda B1S1
Output air fuel ratio associated with bank 1 sensor 1/
Min.: 0, Max.: 1.99
  1. Value less than 1 (0.000 to 0.999) = Rich
  2. 1 = Stoichiometric air fuel ratio
  3. Value more than 1 (1.001 to 1.999) = Lean
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 1.001
  2. Running without load (3000 rpm): 1.001
Diagnostic Note:
This is the actual air fuel ratio calculated based on the air fuel ratio sensor output.
Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check the voltage output of the sensor.
Results of real-vehicle check when performing the Active Test:
Injection Volume: +/-0%
  1. AF Lambda B1S1: 0.99
  2. AFS Voltage B1S1: 3.29 V
  3. AFS Current B1S1: 0.00 mA
  4. O2S B1S2: 0.8 V
Injection Volume: -12%
  1. AF Lambda B1S1: 1.17
  2. AFS Voltage B1S1: 3.91 V
  3. AFS Current B1S1: 0.22 mA
  4. O2S B1S2: 0.015 V
Injection Volume: 12%
  1. AF Lambda B1S1: 0.93
  2. AFS Voltage B1S1: 2.83 V
  3. AFS Current B1S1: -0.16 mA
  4. O2S B1S2: 0.95 V

AFS Voltage B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
AFS Voltage B1S1
Air fuel ratio sensor output voltage for bank 1 sensor 1/
Min.: 0 V, Max.: 7.99 V
2.6 to 3.8 V: Idling
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 3.34 V
  2. Running without load (3000 rpm): 3.30 V
  3. Fuel-cut during deceleration being performed: 4.99 V
Diagnostic Note:
  1. This is the voltage output of the air fuel ratio sensor (the voltage cannot be measured at the terminals of the sensor). This value is calculated by the ECM based on the current output of the air fuel ratio sensor (refer to AFS Current B1S1 below for the actual sensor output).
  2. Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.

AFS Current B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
AFS Current B1S1
Air fuel ratio sensor output current for bank 1 sensor 1/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 0.0 mA
  2. Running without load (3000 rpm): 0.0 mA
  3. Fuel-cut during deceleration being performed: 1.61 mA
Diagnostic Note:
  1. With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor current output is approximately -0.5 to 0.5 mA.
  2. When the value is outside the range of 0.7 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor or sensor circuit.

A/F Heater Duty #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Heater Duty #1
Air fuel ratio sensor heater duty ratio for bank 1/
Min.: 0%, Max.: 399.9%
0 to 100%
Yes
Results of real-vehicle check:
Idling (engine warmed up): 17.1%
Diagnostic Note:
When the value is any value except 0%, current is being supplied to the heater.

O2S B1S2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2S B1S2
Heated oxygen sensor output voltage for bank 1 sensor 2/
Min.: 0 V, Max.: 1.275 V
0 to 1 V
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 0.075 V
  2. Running without load (3000 rpm): 0.855 V
Diagnostic Note:
This is the output voltage of the heated oxygen sensor.
  1. Values close to 0 V indicate an air fuel ratio leaner than the stoichiometric ratio.
  2. Values close to 1 V indicate an air fuel ratio richer than the stoichiometric ratio.
  3. During air fuel ratio feedback control, the value moves back and forth in the range of 0 to 1 V.
Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check voltage output of the sensor.
Results of real-vehicle check when performing the Active Test:
Injection Volume: -12%
  1. AF Lambda B1S1: 1.17
  2. AFS Voltage B1S1: 3.91 V
  3. AFS Current B1S1: 0.22 mA
  4. O2S B1S2: 0.015 V
Injection Volume: 12%
  1. AF Lambda B1S1: 0.93
  2. AFS Voltage B1S1: 2.83 V
  3. AFS Current B1S1: -0.16 mA
  4. O2S B1S2: 0.95 V

O2S Impedance B1S2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2S Impedance B1S2
Heated oxygen sensor impedance for bank 1 sensor 2/
Min.: 0 ohm, Max.: 21247.67 ohm
5 to 15000 ohm
Yes
Results of real-vehicle check:
Idling (engine warmed up): 183.18 ohm
Diagnostic Note:
After driving approx. 10 min. in an urban area: 5 to 15000 ohm

HINT:
When the value is outside the range of 5 to 15000 ohm, there is a problem in the heated oxygen sensor or sensor circuit.


O2 Heater B1S2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2 Heater B1S2
Heated oxygen sensor heater for bank 1 sensor 2/
Active or Not Act
-
Yes

O2 Heater Curr Val B1S2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2 Heater Curr Val B1S2
Heated oxygen sensor current for bank 1 sensor 2/
Min.: 0 A, Max.: 4.999 A
-
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 1.0 A
  2. Running without load (3000 rpm): 1.0 A
Diagnostic Note:
When the value is any value except 0 A, current is being supplied to the heater.

Short FT #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Short FT #1
Short-term fuel trim for bank 1/
Min.: -100%, Max.: 99.2%
-15 to 15%
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): -0.781%
  2. Running without load (3000 rpm): -2.344%
Diagnostic Note:
This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the air fuel ratio sensor for feedback.

Long FT #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Long FT #1
Long-term fuel trim for bank 1/
Min.: -100%, Max.: 99.2%
-15 to 15%
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 1.562%
  2. Running without load (3000 rpm): -2.344%
Diagnostic Note:
The ECM will learn the Long FT #1 values based on Short FT #1. The goal is to keep Short FT #1 at 0% to keep the air fuel ratio mixture at the stoichiometric ratio.
This value is used to determine whether the system related to air fuel ratio control is malfunctioning.
The condition of the system is determined based on the sum of Short FT #1 and Long FT #1 (excluding times when the system is in transition).
  1. 15% or higher: There may be a lean air fuel ratio.
  2. -15 to 15%: The air fuel ratio can be determined to be normal.
  3. -15% or less: There may be a rich air fuel ratio.
  4. Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and a separate value is stored for each operating range. "Long FT #1" indicates the learned value for the current operating range.
    [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.

A/F Learn Value Idle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Idle #1
Air fuel ratio learn value of idle area (bank 1)/
Min.: -50%, Max.: 49.6%
-15 to 15%
Yes
Diagnostic Note:
Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher).

A/F Learn Value Low #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Low #1
Air fuel ratio learn value of low load area (bank 1)/
Min.: -50%, Max.: 49.6%
-15 to 15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).

A/F Learn Value Mid1 #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Mid1 #1
Air fuel ratio learn value of middle1 load area (bank 1)/
Min.: -50%, Max.: 49.6%
-15 to 15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).

A/F Learn Value Mid2 #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Mid2 #1
Air fuel ratio learn value of middle2 load area (bank 1)/
Min.: -50%, Max.: 49.6%
-15 to 15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).

A/F Learn Value High #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value High #1
Air fuel ratio learn value of high load area (bank 1)/
Min.: -50%, Max.: 49.6%
-15 to 15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).

Total FT #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Total FT #1
Total fuel trim for bank 1/
Min.: -0.5, Max.: 0.496
-0.28 to 0.2: Idling
Yes
Diagnostic Note:
Total FT #1 = Short FT #1 + Long FT #1

Fuel System Status #1, #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel System Status #1
Fuel System Status #2
Fuel system status for bank 1 (bank 2)/
OL, CL, OLDrive, OLFault or CLFault
CL: Idling after warming up (bank 1)
Unused: (bank 2)
Yes
Diagnostic Note:
  1. OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
  2. CL (Closed Loop): Uses feedback to perform fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
CL (Closed Loop): During air fuel ratio feedback control, AF Lambda B1S1 is approximately 1.0 and AFS Voltage B1S1 is approximately 3.3 V.

Ignition System (ignition)

IGN Advance 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg, Max.: 63.5 deg
BTDC 5 to 15 deg: Idling
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 10 deg
  2. Running without load (3000 rpm): 34.5 deg

Knock Feedback Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Knock Feedback Value
Knocking feedback value/
Min.: -1024° CA, Max.: 1023.9° CA
-
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): -3.0° CA
  2. Running without load (3000 rpm): -3.0° CA
Diagnostic Note:
This is the ignition timing retard compensation amount determined by the presence or absence of knocking.
Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock Feedback Value*3 + each compensation amount
Example: 21° CA = 10° CA + 14°CA - 3° CA
*1: The most retarded timing value is a constant determined by the engine speed and engine load.
*2: The knock correction learned value is calculated as shown below in order to keep Knock Feedback Value as close to -3° CA as possible.
When Knock Feedback Value is less than -4° CA, Knock Correct Learn Value is slowly decreased.
When Knock Feedback Value is more than -2° CA, Knock Correct Learn Value is slowly increased.
*3: The base value is -3° CA and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased.
  1. -1° CA: There is no knocking and ignition timing is advanced.
  2. -6° CA: Knocking is present and the ignition timing is being retarded.

HINT:
If Knock Feedback Value does not change around the time when knocking occurs even though knocking continues (for example, stays at -3° CA), it can be determined that knocking is not being detected.
Possible Causes:
  1. There is a problem with the knock control sensor sensitivity.
  2. The knock control sensor is improperly installed.
  3. There is a problem with a wire harness.


Knock Correct Learn Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Knock Correct Learn Value
Knocking correction learned value/
Min.: -1024° CA, Max.: 1023.9° CA
-
Yes
Results of real-vehicle check:
  1. Idling (engine warmed up): 13.2° CA
  2. Running without load (3000 rpm): 13.2° CA
Diagnostic Note:
Refer to "Knock Feedback Value".
When there is knocking or a lack of power, compare the following values to another vehicle of the same model.
  1. Engine Speed
  2. Calculate Load
  3. IGN Advance
  4. Knock Feedback Value
  5. Knock Correct Learn Value
Knock Correct Learn Value is large: There is no knocking and the ignition timing is advanced.
Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.

HINT:
When knocking continues even though Knock Correct Learn Value is less than that of the vehicle being used for comparison (in other words, the ignition timing is being retarded but the knocking is not stopping), there may be a buildup of deposits or other such problems due to deterioration over time (oil entering the cylinders, poor quality fuel, etc.).


Idle Spark Advn Ctrl #1 to #4 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Idle Spark Advn Ctrl #1
Idle Spark Advn Ctrl #2
Idle Spark Advn Ctrl #3
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 1 to No. 4)/
Min.: 0° CA, Max.: 15.93° CA
-
Yes
Diagnostic Note:
  1. This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.
  2. It may be possible to use this item to help determine specific cylinders which are not operating normally.

Intake Control 2 (Gas Intake Control)

ACIS VSV 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ACIS VSV
VSV status for ACIS (Acoustic Control Induction System) control/
ON or OFF
-
Yes
Diagnostic Note:
This is the ECM control command.

IAC Sensor Voltage 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
IAC Sensor Voltage
Intake air control valve position sensor output voltage/
Min.: 0 V, Max.: 4.999 V
-
Yes
Diagnostic Note:
If the value is 0.2 V or less:
  1. The IAC1 circuit is shorted.
  2. The VCIA circuit is open.
If the value is 4.8 V or higher:
  1. The VCIA and IAC1 circuits are shorted.
  2. The IAC1 circuit is open.
  3. The EIA1 circuit is open.

Intake Air Control Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Intake Air Control Position
Intake air control valve position/
Min.: -250 deg, Max.: 249 deg
-
Yes
Diagnostic Note:
This is the value of the tumble control valve position sensor.

VVT Control 1 (All Data)

Actual VVT Angle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Actual VVT Angle #1
VVT displacement angle for bank 1/
Min.: 0 DegFR, Max.: 639.99 DegFR
-
Yes
Diagnostic Note:
This is the VVT displacement angle for the intake camshaft.
This is only available in Freeze Frame Data.

Actual VVT Ex Angle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Actual VVT Ex Angle #1
Exhaust VVT displacement angle for bank 1/
Min.: 0 DegFR, Max.: 639.99 DegFR
-
Yes
Diagnostic Note:
This is the VVT displacement angle for the exhaust camshaft.
This is only available in Freeze Frame Data.

VVT Control 2 (Gas Valve Control)

VVT Control Status #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Control Status #1
Variable Valve Timing (VVT) control status for bank 1/
ON or OFF
-
Yes
Diagnostic Note:
ON: The ECM is sending commands to change the timing (even when the timing is advanced, when the timing is being maintained and not being retarded or advanced any further, the value changes to OFF).
OFF: The system is commanding the timing to change to the most retarded timing.

VVT Advance Fail 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Advance Fail
VVT control failure status/
ON or OFF
ON: VVT control failure
Yes
Diagnostic Note:
ON: There is an intake VVT timing advance malfunction.

VVT Aim Angle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Aim Angle #1
VVT hold duty learned value for bank 1/
Min.: 0%, Max.: 399.9%
-
No
Diagnostic Note:
This value represents the duty ratio necessary to operate the camshaft timing oil control valve assembly in order to block the camshaft timing oil control valve assembly path and maintain the advanced state of the VVT controller. This is only available during the Active Test.
Refer to "VVT OCV Duty #1".

VVT Change Angle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Change Angle #1
VVT displacement angle for bank 1/
Min.: 0 DegFR, Max.: 639.9 DegFR
-
No
Diagnostic Note:
This is the VVT displacement angle during forced operation.
This is only available during the Active Test.
By checking VVT Change Angle during the Active Test, it is also possible to determine whether or not the camshaft position sensor signal is being output.
Refer to "VVT OCV Duty #1".

VVT OCV Duty #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT OCV Duty #1
VVT camshaft timing oil control valve operation duty for bank 1/
Min.: 0%, Max.: 399.9%
-
No
Diagnostic Note:
This is the requested duty value for forced operation.
This is only available during the Active Test.
Results of the real-vehicle check when performing the Control the VVT Linear (Bank 1) Active Test:
VVT OCV Duty #1 = 0%, VVT Change Angle #1 = 0 DegFR
↓
VVT OCV Duty #1 = 30%, VVT Change Angle #1 = 0 DegFR
↓
VVT OCV Duty #1 = 70%, VVT Change Angle #1 = 39.0 DegFR
↓
VVT OCV Duty #1 = 100%, VVT Change Angle #1 = 39.0 DegFR
↓
VVT OCV Duty #1 = 32%, VVT Change Angle #1 = 0 DegFR
After the above test, VVT Aim Angle #1 = 26.6%.

VVT Ex Hold Lrn Val #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Ex Hold Lrn Val #1
VVT exhaust hold duty ratio learned value for bank 1/
Min.: 0%, Max.: 399.9%
-
No
Diagnostic Note:
This value represents the duty ratio necessary to operate the camshaft timing oil control valve assembly in order to block the camshaft timing oil control valve assembly path and maintain the advanced state of the VVT controller. This is only available during the Active Test.
Refer to "VVT Ex OCV Duty #1".

VVT Ex Chg Angle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Ex Chg Angle #1
VVT exhaust displacement angle for bank 1/
Min.: 0 DegFR, Max.: 639.9 DegFR
-
No
Diagnostic Note:
This is the displacement angle during forced operation.
Refer to "VVT Ex OCV Duty #1".

VVT Ex OCV Duty #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Ex OCV Duty #1
VVT exhaust camshaft timing oil control valve duty for bank 1/
Min.: 0%, Max.: 399.9%
-
No
Diagnostic Note:
This is the requested duty value for forced operation.
This is only available during the Active Test.
Results of the real-vehicle check when performing the Control the VVT Exhaust Linear (Bank 1) Active Test:
VVT Ex OCV Duty #1 = 0%, VVT Ex Chg Angle #1 = 0 DegFR
↓
VVT Ex OCV Duty #1 = 30%, VVT Ex Chg Angle #1 = 0 DegFR
↓
VVT Ex OCV Duty #1 = 70%, VVT Ex Chg Angle #1 = 38.5 DegFR
↓
VVT Ex OCV Duty #1 = 100%, VVT Ex Chg Angle #1 = 38.5 DegFR
↓
VVT Ex OCV Duty #1 = 27.4%, VVT Ex Chg Angle #1 = 0 DegFR
After the above test, VVT Ex Hold Lrn Val #1 = 44.0%.

Various Vehicle Conditions 2 (All Data)

VN Turbo Type 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VN Turbo Type
VN turbo type/
Not avl, Commo, Vacuum or CAN Com
Not Avl
No

Catalyst (Gas CAT Converter)

Catalyst Temp B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Catalyst Temp B1S1
Catalyst temperature for bank 1 sensor 1/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
-
Yes
Diagnostic Note:
This is the temperature of the front catalyst estimated by the ECM.
This value is included in the conditions used to detect catalyst deterioration (DTC P0420), etc., and should therefore be used as a reference when recreating malfunction conditions.

Catalyst Temp B1S2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Catalyst Temp B1S2
Catalyst temperature for bank 1 sensor 2/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
-
Yes
Diagnostic Note:
This is the temperature of the rear catalyst estimated by the ECM.

Various Vehicle Conditions 3 (All Data)

Starter Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Starter Signal
Starter signal/
Open or Close
Open: Starter operating
Close: Starter not operating
Yes

Power Steering Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Power Steering Signal
Power steering switch signal/
ON or OFF
ON: Power steering operating
Yes

Neutral Position SW Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Neutral Position SW Signal
Park/neutral position switch status/
ON or OFF
ON: Shift lever in P or N
Yes

Stop Light Switch 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Stop Light Switch
Stop light switch/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal fully released
Yes

A/C Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/C Signal
A/C switch status/
ON or OFF
ON: A/C on
Yes

Idle Up Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Idle Up Signal
Idle up signal/
ON or OFF
-
Yes

Closed Throttle Position SW 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Closed Throttle Position SW
Closed throttle position switch/
ON or OFF
  1. ON: Throttle fully closed
  2. OFF: Throttle open
Yes

Fuel Cut Condition 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Cut Condition
Fuel cut condition/
ON or OFF
ON: Fuel cut operating
Yes

Immobiliser Communication 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Immobiliser Communication
Immobiliser communication/
ON or OFF
ON: Normal
Yes

Check Mode (Check Mode)

Check Mode 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stored as Freeze Frame Data
Check Mode
Check mode/
ON or OFF
ON: Check mode on
Refer to Check Mode Procedure (Click here).
No
SPD Test Result
Check mode result for vehicle speed sensor/
Compl or Incmpl
-
-
No
Misfire Test Result
Check mode result for misfire monitor/
Compl or Incmpl
-
-
No
OXS1 Test Result
Check mode result for heated oxygen sensor (bank 1)/
Compl or Incmpl
-
-
No
A/F Test Results #1
Check mode result for air fuel ratio sensor (bank 1)/
Compl or Incmpl
-
-
No

Test Result (Monitor Status)

Monitor Information 1 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stored as Freeze Frame Data
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
*1
No
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
*1
No
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
*1
No
EGR/VVT Monitor
EGR/VVT monitor/
Not Avl or Avail
-
*1
No
EGR/VVT Monitor
EGR/VVT monitor/
Compl or Incmpl
-
*1
No
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Not Avl or Avail
-
*1
No
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Compl or Incmpl
-
*1
No
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Not Avl or Avail
-
*1
No
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Compl or Incmpl
-
*1
No
A/C Monitor
A/C monitor/
Not Avl or Avail
-
*1
No
A/C Monitor
A/C monitor/
Compl or Incmpl
-
*1
No
2nd Air Monitor
2nd air monitor/
Not Avl or Avail
-
*1
No
2nd Air Monitor
2nd air monitor/
Compl or Incmpl
-
*1
No
EVAP Monitor
EVAP monitor/
Not Avl or Avail
-
*1
No
EVAP Monitor
EVAP monitor/
Compl or Incmpl
-
*1
No
Heated Catalyst Monitor
Heated catalyst monitor/
Not Avl or Avail
-
*1
No
Heated Catalyst Monitor
Heated catalyst monitor/
Compl or Incmpl
-
*1
No
Catalyst Monitor
Catalyst monitor/
Not Avl or Avail
-
*1
No
Catalyst Monitor
Catalyst monitor/
Compl or Incmpl
-
*1
No
*1:
Avail: The monitor is available on the vehicle.
Not Avl: The monitor is not available on the vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
Monitor result (mode 06): The last judgment result is output. This is not cleared when the ignition switch is turned off, but is cleared when DTCs are cleared.

Monitor Information 2 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stored as Freeze Frame Data
Component Monitor ENA
Comprehensive component monitor/
Unable or Enable
-
*2
No
Component Monitor CMPL
Comprehensive component monitor/
Compl or Incmpl
-
*2
No
Fuel System Monitor ENA
Fuel system monitor/
Unable or Enable
-
*2
No
Fuel System Monitor CMPL
Fuel system monitor/
Compl or Incmpl
-
*2
No
Misfire Monitor ENA
Misfire monitor/
Unable or Enable
-
*2
No
Misfire Monitor CMPL
Misfire monitor/
Compl or Incmpl
-
*2
No
EGR/VVT Monitor ENA
EGR monitor/
Unable or Enable
-
*2
No
EGR/VVT Monitor CMPL
EGR monitor/
Compl or Incmpl
-
*2
No
Heater Monitor ENA
O2S (A/FS) heater monitor/
Unable or Enable
-
*2
No
Heater Monitor CMPL
O2S (A/FS) heater monitor/
Compl or Incmpl
-
*2
No
O2S(A/FS) Monitor ENA
O2S (A/FS) monitor/
Unable or Enable
-
*2
No
O2S(A/FS) Monitor CMPL
O2S (A/FS) monitor/
Compl or Incmpl
-
*2
No
A/C Monitor ENA
A/C monitor/
Unable or Enable
-
*2
No
A/C Monitor CMPL
A/C monitor/
Compl or Incmpl
-
*2
No
2nd Air Monitor ENA
2nd air monitor/
Unable or Enable
-
*2
No
2nd Air Monitor CMPL
2nd air monitor/
Compl or Incmpl
-
*2
No
EVAP Monitor ENA
EVAP monitor/
Unable or Enable
-
*2
No
EVAP Monitor CMPL
EVAP monitor/
Compl or Incmpl
-
*2
No
Heated Cat Monitor ENA
Heated catalyst monitor/
Unable or Enable
-
*2
No
Heated Cat Monitor CMPL
Heated catalyst monitor/
Compl or Incmpl
-
*2
No
Catalyst Monitor ENA
Catalyst monitor/
Unable or Enable
-
*2
No
Catalyst Monitor CMPL
Catalyst monitor/
Compl or Incmpl
-
*2
No
*2:
Enable: The monitor is available on the vehicle.
Unable: The monitor is not available on the vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed during the current trip. The item changes back to Incmpl when the ignition switch is turned off.
Monitor result (mode 06): The last judgment result is output. This is not cleared when the ignition switch is turned off, but is cleared when DTCs are cleared. Therefore, only when DTCs are cleared at the beginning of a trip do the system monitor (Monitor Information 2) and monitor result (mode 06) match.

Various Vehicle Conditions 4 (All Data)

TC Terminal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
TC Terminal
TC terminal status/
ON or OFF
-
Yes

# Codes(Include History) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
# Codes(Include History)
Number of codes/
Min.: 0, Max.: 255
0
No
Diagnostic Note:
This is the number of DTCs stored.

MIL 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MIL
MIL status/
ON or OFF
OFF
No

MIL ON Run Distance 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MIL ON Run Distance
Distance driven with MIL on/
Min.: 0 Km (0 mile), Max.: 65535 Km (40723 mile)
-
No
Diagnostic Note:
This is the distance driven after a DTC is stored.

Running Time from MIL ON 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Running Time from MIL ON
Running time from MIL ON/
Min.: 0 min, Max.: 65535 min
Running time after MIL turned on
No

Time after DTC Cleared 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Time after DTC Cleared
Time after DTCs cleared/
Min.: 0 min, Max.: 65535 min
Time after DTCs cleared
Yes
Diagnostic Note:
This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the ignition switch is turned off is not counted.

Distance from DTC Cleared 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Distance from DTC Cleared
Distance driven after DTCs cleared/
Min.: 0 km (0 mile), Max.: 65535 km (40723 mile)
Distance driven after DTCs cleared
Yes
Diagnostic Note:
This is the distance driven after DTCs were cleared (or after the vehicle left the factory).

Warmup Cycle Cleared DTC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Warmup Cycle Cleared DTC
Warmup cycles after DTCs cleared/
Min.: 0, Max.: 255
-
Yes
Diagnostic Note:
This is the number of warmup cycles after the DTCs were cleared.
This is the number of times the engine was warmed up* after DTCs were cleared (or after the vehicle left the factory).
*: An engine warmup is defined as the engine coolant temperature rising 20°C (36°F) or higher and reaching a temperature of 70°C (158°F) or higher after the engine is started.

Dist Batt Cable Disconnect 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Dist Batt Cable Disconnect
Distance driven after battery cable disconnected/
Min.: 0 Km (0 mile), Max.: 65535 Km (40723 mile)
Total distance vehicle driven after battery cable disconnected
Yes

IG OFF Elapsed Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
IG OFF Elapsed Time
Time after ignition switch off/
Min.: 0 min, Max.: 655350 min
Cumulative time after ignition switch off
Yes

OBD Requirements 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
OBD Requirements
OBD requirement
OBD2 (California ARB)
No

Number of Emission DTC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Number of Emission DTC
Emissions-related DTCs
-
No
Diagnostic Note:
This is the number of emissions-related DTCs.

TC and TE1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
TC and TE1
TC and CG (TE1) terminals of DLC3/
ON or OFF
-
Yes

Total Distance Traveled 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Total Distance Traveled
Total distance traveled/
Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile)
-
Yes

Misfire (Gas Misfire)

Ignition Trig. Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Ignition Trig. Count
Ignition counter/
Min.: 0, Max.: 65535
0 to 400
Yes
Diagnostic Note:
This is the cumulative number of ignitions.
This counter is incremented by one for each ignition (this stops when misfire monitoring stops). This value is cleared every 200 revolutions.
The misfire rate for each cylinder is calculated by dividing the misfire count for each cylinder by Ignition Trig. Count.
The misfire rate for each cylinder = Cylinder 1 to 4 Misfire Count / Ignition Trig. Count

HINT:
  1. For 4-cylinder engines, the values range from 0 to 400.
  2. For 6-cylinder engines, the values range from 0 to 600.
  3. For 8-cylinder engines, the values range from 0 to 800.


Cylinder #1 Misfire Count to Cylinder #4 Misfire Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Cylinder #1 Misfire Count
Cylinder #2 Misfire Count
Cylinder #3 Misfire Count
Cylinder #4 Misfire Count
Misfire count of cylinders 1 to 4/
Min.: 0, Max.: 255
0
Yes
Diagnostic Note:
This is the misfire count for each individual cylinder.
This counter is increased by one for each misfire and is cleared every 200 revolutions.
Check this item to help determine the malfunctioning cylinder.

All Cylinders Misfire Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
All Cylinders Misfire Count
Misfire count of all cylinders/
Min.: 0, Max.: 255
0 to 35
Yes
Diagnostic Note:
This is the total misfire count of all cylinders.
This counter is increased by one for each misfire, has a maximum value of 255 and is cleared every 1000 revolutions.

Misfire RPM 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Misfire RPM
Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: 0 misfires
Yes
Diagnostic Note:
  1. This is the average engine speed recorded when misfiring occurs.
  2. This value is closer to the actual conditions of the vehicle at the time misfire occurred than the values of engine speed and engine load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference.

Misfire Load 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Misfire Load
Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: 0 misfires
Yes
Diagnostic Note:
  1. This is the average engine load recorded when misfiring occurs.
  2. This value is closer to the actual conditions of the vehicle at the time misfire occurred than the values of engine speed and engine load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference.

HINT:
To convert g/rev to gm/sec: RPM / 60 x g/rev = gm/sec.


Misfire Margin 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Misfire Margin
Misfire monitoring/
Min.: -128%, Max.: 127%
0 to 127%: Idling
Yes
Diagnostic Note:
This is the misfire detection margin.
Misfire Margin = (Misfire detection threshold - maximum engine speed variation) / misfire detection threshold x 100%
When the variation in the engine speed is large and exceeds the misfire detection threshold, the misfire count starts. Misfire margin is a measure of how much the engine speed variation can increase with respect to the threshold before the engine is determined to be misfiring.
A large value means there is a large margin for the engine speed to vary before the engine is determined to be misfiring.
Example:
When the engine is determined to be misfiring, Misfire Margin = -128 to 0%.

Catalyst OT MF F/C 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Catalyst OT MF F/C
Fuel cut to prevent catalyst from overheating during misfire/
Not Avl or Avail
Avail: "Fuel cut to prevent catalyst from overheating during misfire" available
Not Avl: "Fuel cut to prevent catalyst from overheating during misfire" not available
Yes
Diagnostic Note:
For vehicles which support this function, Catalyst OT MF F/C is displayed as "Avail".
  1. When a high frequency of misfires is concentrated in a certain cylinder, this function stops fuel injection for that cylinder.
  2. For vehicles which support this function, stop this fuel cut using the Active Test and confirm the misfire counts to determine the malfunctioning cylinder.

Cat OT MF F/C History 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Cat OT MF F/C History
History of fuel cut to prevent catalyst from overheating during misfire/
ON or OFF
-
Yes
Diagnostic Note:
This can be used to tell whether there was a large amount of misfires concentrated in a certain cylinder.

Cat OT MF F/C Cylinder #1 to #4 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Cat OT MF F/C Cylinder #1
Cat OT MF F/C Cylinder #2
Cat OT MF F/C Cylinder #3
Cat OT MF F/C Cylinder #4
Display of fuel cut operation in No. 1 to No. 4 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
-
Yes

Various Vehicle Conditions 5 (All Data)

Engine Speed (Starter Off) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed (Starter Off)
Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
-
Yes
Result of real-vehicle check:
Idling (engine warmed up): 890 rpm
Diagnostic Note:
This is the engine speed immediately after starting the engine.

Starter Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Starter Count
Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
-
Yes
Diagnostic Note:
This is the number of times the starter turned on during the current trip.

Run Dist of Previous Trip 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Run Dist of Previous Trip
Distance driven during previous trip/
Min.: 0 km (0 mile), Max.: 655.35 km (407.23 mile)
-
Yes
Diagnostic Note:
Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

HINT:
Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when the DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.


Engine Starting Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Starting Time
Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm)/
Min.: 0 ms, Max.: 655350 ms
-
Yes
Diagnostic Note:
This is the time elapsed after the starter turns on until the engine speed reaches 400 rpm.
This value is cleared 5 seconds after the engine is started and the value is displayed as 0 ms.

Previous Trip Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Coolant Temp
Engine coolant temperature during previous trip/
Min.: -40°C (-40°F), Max.: 215°C (419°F)
-
Yes
Diagnostic Note:
Before 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature at the end of the previous trip.
After 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature during the current trip.

Previous Trip Intake Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Intake Temp
Intake air temperature during previous trip/
Min.: -40°C (-40°F), Max.: 215°C (419°F)
-
Yes
Diagnostic Note:
Before 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature at the end of the previous trip.
After 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature during the current trip.

Engine Oil Temperature 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Oil Temperature
Engine oil temperature (estimated temperature)/
Min.: -40°C (-40°F), Max.: 215°C (419°F)
-
Yes

Previous Trip Eng Oil Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip/
Min.: -40°C (-40°F), Max.: 215°C (419°F)
-
Yes

Ambient Temp for A/C 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Ambient Temp for A/C
Ambient temperature for A/C/
Min.: -40°C (-40°F), Max.: 215°C (419°F)
-
Yes

Previous Trip Ambient Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Ambient Temp
Ambient temperature during previous trip/
Min.: -40°C (-40°F), Max.: 215°C (419°F)
-
Yes

Engine Start Hesitation 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Start Hesitation
History of hesitation during engine start/
ON or OFF
-
Yes
Diagnostic Note:
This value changes to ON when the engine speed does not reach 500 rpm during cranking.

Low Rev for Eng Start 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Low Rev for Eng Start
History of low engine speed after engine start/
ON or OFF
-
Yes
Diagnostic Note:
This item changes to ON when the engine speed drops to 200 rpm or less within approximately 2 seconds of starting the engine.

Minimum Engine Speed 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Minimum Engine Speed
Minimum engine speed/
Min.: 0 rpm, Max.: 51199 rpm
-
Yes
Diagnostic Note:
  1. This is the lowest engine speed detected throughout the trip after the engine is started and ISC learning is completed.
  2. For use when engine stall, starting problems or rough idle is present.

Intake Control 3 (Gas Intake Control)

Tumble C.V Duty Ratio 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Tumble C.V Duty Ratio
Intake air control valve actuator for tumble control valve duty ratio/
Min.: -128%, Max.: 127%
-
Yes
Diagnostic Note:
This is the intake air control valve actuator for tumble control valve duty ratio.

Various Vehicle Conditions 6 (All Data)

Electric Fan Motor 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electric Fan Motor
Electric fan motors operation status/
ON or OFF
-
Yes

Brake Override System 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Brake Override System
Brake override system status/
ON or OFF
ON: Brake override system operating
Yes

Idle Fuel Cut 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Idle Fuel Cut
Fuel cut at idle/
ON or OFF
ON: Fuel cut operating
Yes
Diagnostic Note:
Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is high.

FC TAU 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
FC TAU
Fuel cut TAU (fuel cut during very light load)/
ON or OFF
ON: Fuel cut operating
Yes
Diagnostic Note:
This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete.

Immobiliser Fuel Cut 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Immobiliser Fuel Cut
Status of immobiliser fuel cut/
ON or OFF
-
Yes

Immobiliser Fuel Cut History 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Immobiliser Fuel Cut History
Immobiliser fuel cut history/
ON or OFF
OFF
Yes
Diagnostic Note:
When DTC P1604 is output and Immobiliser Fuel Cut History indicates ON, the engine could not start due to engine immobiliser operation.

Electrical Load Signal 1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electrical Load Signal 1
Electrical load signal/
ON or OFF
-
Yes

Electrical Load Signal 3 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electrical Load Signal 3
Electrical load signal/
ON or OFF
-
Yes

Various Vehicle Conditions 7 (Vehicle Information)

Model Code 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Model Code
Model code
-
No
Diagnostic Note:
Used for identifying the model code: ASV5#

Engine Type 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Type
Engine type
-
No
Diagnostic Note:
Used for identifying the engine type: 2ARFE

Cylinder Number 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Cylinder Number
Number of cylinders/
Min.: 0, Max.: 255
-
No
Diagnostic Note:
Used for identifying the number of cylinders: 4

Transmission Type 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Transmission Type
Transmission (transaxle) type
-
No
Diagnostic Note:
Used for identifying the transmission (transaxle) type: ECT 6th

Destination 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Destination
Destination
-
No
Diagnostic Note:
Used for identifying the destination: A (America)

Model Year 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Model Year
Model year/
Min.: 1900, Max.: 2155
-
No
Diagnostic Note:
Used for identifying the model year: 2012

System Identification 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
System Identification
System identification
-
No
Diagnostic Note:
Used for identifying the engine system: Gasoline (gasoline engine)

Compression (Compression)

Engine Speed of Cyl #1 to #4 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
Engine speed for cylinder No. 1 to No. 4/
Min.: 0 rpm, Max.: 51199 rpm
-
No
Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test.
This is the engine speed for each cylinder measured during the fuel-cut with the engine cranking.
When there is compression loss, the engine speed for that cylinder increases.

HINT:
When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.

Results of real-vehicle check when performing the Active Test with a normal vehicle:
  1. Engine Speed of Cyl #1: 228 rpm
  2. Engine Speed of Cyl #2: 230 rpm
  3. Engine Speed of Cyl #3: 228 rpm
  4. Engine Speed of Cyl #4: 231 rpm

Av Engine Speed of All Cyl 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Av Engine Speed of All Cyl
Average engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
-
No
Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test.

Air Fuel Ratio Cylinder Imbalance (Gas AF O2 Sensor)

A/F Sensor Determination (worst value) #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Sensor Determination (worst value) #1
Worst judgment value of air fuel ratio sensor output (bank 1)/
Min.: -1, Max.: 0.99
0.00
Yes
Diagnostic Note:
  1. The worst value detected during monitoring is displayed.
  2. The value is reset when DTCs are cleared.

Engine Speed Fluctuation Avg (worst value) #1 to #4 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed Fluctuation Avg (worst value) #1
Engine Speed Fluctuation Avg (worst value) #2
Engine Speed Fluctuation Avg (worst value) #3
Engine Speed Fluctuation Avg (worst value) #4
Worst value of average engine speed fluctuation (cylinder 1 to 4)/
Min.: 0, Max.: 2.55
0.00
Yes
Diagnostic Note:
  1. The worst value detected during monitoring is displayed.
  2. The value is reset when DTCs are cleared.

ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5% and 24.8%
    1. All fuel injector assemblies are tested at the same time.
    2. Perform the test at 3000 rpm or less.
    3. Injection volume can be changed in fine gradations within the control range.
    4. Control the Injection Volume enables the checking and graphing of the air fuel ratio sensor and heated oxygen sensor voltage outputs.
    5. To conduct the test, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Gas AF Control / AFS Voltage B1S1 and O2S B1S2.
    6. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
    7. See waveform *3.
    Control the Injection Volume for A/F Sensor
    Change injection volume
    -12.5%/0%/12.5%
    1. All fuel injector assemblies are tested at the same time.
    2. Perform the test at 3000 rpm or less.
    3. Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor and heated oxygen sensor voltage outputs.
    4. To conduct the test, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Gas AF Control / AFS Voltage B1S1 and O2S B1S2.
    5. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
    Activate the VSV for Intake Control
    Activate vacuum switching valve (for acoustic control induction system)
    ON/OFF
    1. ON: Acoustic control induction system VSV is on.
    2. OFF: Acoustic control induction system VSV is off.
    3. This test can only be operated for 10 seconds.
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    1. The purge VSV is opened with a 30% duty ratio.
    2. See waveform *5.
    Control the Fuel Pump / Speed
    Activate fuel pump
    ON/OFF
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever in P.
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 are connected.
    2. OFF: TC and TE1 are disconnected.
    3. Perform this test when the following conditions are met:
      1. Ignition switch is ON.
      2. Engine is stopped.
      3. Shift lever in P.
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever in P.
    Prohibit the Catalyst OT Misfire prevent F/C
    Prohibit fuel cut which prevents catalyst from overheating during misfire
    ON/OFF
    ON: Fuel cut prohibited
    Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
    Control the Electric Cooling Fan
    Control electric cooling fan motor
    ON/OFF
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever in P.
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    Close/Open
    Open: Throttle valve opens slowly
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Accelerator pedal is fully depressed (accelerator pedal position: 58 degrees or more).
    4. Shift lever in P.
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    Close/Open
    Open: Throttle valve opens quickly
    1. Same as above.
    2. See waveform *4.
    Control the VVT Linear (Bank 1)
    Control camshaft timing oil control valve assembly (for intake camshaft of bank 1)
    -128 to 127% (This value added to present camshaft timing oil control valve control duty)
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.
    2. Perform this test when the following conditions are met:
      1. Engine is idling.
      1. Shift lever in P.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    4. See waveform *6.
    Control the VVT System (Bank 1)
    Turn camshaft timing oil control valve on and off
    ON/OFF
    ON: VVT OCV Duty #1 100%
    1. Engine stalls or idles roughly when the camshaft timing oil control valve assembly is turned on.
    2. Engine runs and idles normally when the camshaft timing oil control valve assembly is off.
    3. Perform this test when the following conditions are met:
      1. Engine is idling.
      1. Shift lever in P.
    4. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Exhaust Linear (Bank 1)
    Control camshaft timing oil control valve assembly (for exhaust camshaft of bank 1)
    -128 to 127% (This value added to present camshaft timing oil control valve control duty)
    100%: Maximum retard
    -100%: Maximum advance
    1. Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.
    2. Perform this test when the following conditions are met:
      1. Engine is idling.
      1. Shift lever in P.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    4. See waveform *7.
    Activate the Vacuum Pump
    Activate leak detection pump (built into canister pump module)
    ON/OFF
    Refer to EVAP system (Click here).
    Activate the VSV for Vent Valve
    Activate vent valve (built into canister pump module)
    ON/OFF
    Refer to EVAP system (Click here).
    Control the IAC Duty Ratio
    Control intake air control valve actuator duty ratio for tumble control valve
    Between -100 and 100%
    Perform this test when the following conditions are met:
    1. Ignition switch is ON.
    2. Engine is stopped.
    3. Shift lever in P.
    This test can only be operated for 10 seconds.
    Control the Select Cylinder Fuel Cut
    Selected cylinder (cylinder #1 to #4) injector fuel cut
    #1/#2/#3/#4
    ON/OFF
    Perform this test when the following conditions are met:
    1. Vehicle is stopped.
    2. Engine is idling.
    3. Shift lever in P.
    *1
    Control the All Cylinders Fuel Cut
    Fuel cut for all cylinders
    ON/OFF
    This test possible when the following conditions are met:
    1. Vehicle is stopped.
    2. Engine is idling.
    3. Shift lever in P.
    *1
    Check the Cylinder Compression
    Check the cylinder compression pressure
    ON/OFF
    Fuel injection and ignition stop in all cylinders.
    *2
    Check the Imbalance Cylinder
    Selected cylinder (cylinder #1 to #4) fuel injection volume change
    Between 50 and 200%
    1. Perform this test when the following conditions are met:
      1. Engine is idling.
      1. Shift lever in P.
    2. At the time this Active Test item is entered = 100%
      1. Below 100% = Fuel injection volume is decreased
      2. Higher than 100% = Fuel injection volume is increased
    3. To conduct the test, enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Imbalance Cylinder / Gas AF Control / A/F Sensor Determination (worst value) and Engine Speed Fluctuation Avg (worst value).
    4. Refer to DTC P219A (Click here).

    NOTICE:
    *1:
    1. If the display of the Data List item Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
    2. If the display of the Data List item Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
      1. Stop the engine, turn the ignition switch to ON.
      2. Enter the Control the Select Cylinder Fuel Cut.
      3. Select the cylinder for fuel cut (cylinder #1 to #4) and turn the Active Test ON (press the RIGHT or LEFT button).
      4. Start the engine.

    HINT:
    *2: In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

      HINT:
      To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

    7. Push the snapshot button to turn the snapshot function on.

      HINT:
      Using the snapshot function, data can be recorded during the Active Test.

    8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

    9. Crank the engine for about 10 seconds.

      HINT:
      Continue to crank the engine until the values change from the default value (51199 rpm).


    10. A242113
      Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the Techstream.

      HINT:
      At first, the Techstream displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

      NOTICE:
      1. Do not crank the engine continuously for 20 seconds or more.
      2. If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
      3. Use a fully-charged battery.

    11. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

      NOTICE:
      If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

    12. Push the snapshot button to turn the snapshot function off.
    13. Select "Stored Data" on the Techstream screen, select the recorded data and display the data as a graph.

      HINT:
      If the data is not displayed as a graph, the change of the values cannot be observed.

    14. Check the change in engine speed values.

      HINT:
      As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.

  1. Reference Waveforms for Active Test

    1. *3: Control the Injection Volume (Idling after warming up)


      A227144E05

      HINT:
      During the Active Test, air fuel ratio feedback control and feedback learning are stopped.


      Tester Display
      Measurement Item/Range
      Normal Condition
      Control the Injection Volume
      -
      ▲A
      ▲B
      Active Test operation
      -12%
      12%
      AFS Voltage B1S1
      3.908 V
      2.868 V
      O2S B1S2
      0.055 V
      0.955 V

      HINT:
      1. Usually, the value of AFS Voltage B1S1 drops below 3.1 V when the control value for Control the Injection Volume is changed to 12%.
      2. Usually, the value of AFS Voltage B1S1 changes to 3.4 V or higher when the control value for Control the Injection Volume is changed to -12%.
      3. Usually, the value of O2S B1S2 changes to 0.55 V or higher when the control value for Control the Injection Volume is changed to 12%.
      4. Usually, the value of O2S B1S2 drops below 0.4 V when the control value for Control the Injection Volume is changed to -12%.


    2. *4: Control the ETCS Open/Close Fast Speed [Active Test for electrical throttle control system] (Ignition switch ON)


      A227143E06

      HINT:
      1. Usually, Throttle Position Command (Target Value) and Throttle Position No. 1 (Actual Value) are almost the same.
      2. If any DTCs related to the Electronic Throttle Control System (ETCS) are stored, this Active Test does not function.


      Tester Display
      Measurement Item/Range
      Normal Condition
      Control the ETCS Open/Close Fast Speed
      -
      ▲A
      ▲B
      Active Test operation
      Open
      Close
      Throttle Position Command
      2.597 V
      0.742 V
      Throttle Position No. 1
      2.597 V
      0.742 V
      Throttle Motor Duty (Open)
      11%
      0%
      Throttle Motor Duty (Close)
      0%
      12%

    3. *5: Activate the VSV for Evap Control (Idling after warming up)


      A233254E11

      HINT:
      Even when the Active Test is turned on (the purge VSV is opened 30%), air fuel ratio feedback continues and control is performed so that the air fuel ratio is the stoichiometric ratio. Therefore, by observing the change in "Short FT #1", it is possible to determine whether the purge VSV is actually open as well as the concentration of HC in the purge gas.


      Tester Display
      Measurement Item/Range
      Normal Condition
      Activate the VSV for Evap Control
      -
      ▲A
      ▲B
      Active Test operation
      ON
      OFF
      EVAP (Purge) VSV
      29.8%
      0%
      Short FT #1
      -9.375%
      0.000%
      Injector (Port)
      2495 μs
      2541 μs
      AFS Voltage B1S1
      3.249 V
      3.205 V

      HINT:
      The graphs and values above are for reference only because the fuel injection volume (compensation volume) varies depending on the HC density of the purge air from the canister.


    4. *6: Control the VVT Linear (Bank 1)


      A229971E06


      Tester Display
      Measurement Item/Range
      Normal Condition
      Control the VVT Linear (Bank 1)
      -
      ▲A
      ▲B
      Active Test operation*
      20%
      -20%
      VVT Change Angle #1
      54.1 DegFR
      0.0 DegFR
      VVT OCV Duty #1
      57.4%
      7.4%
      VVT Aim Angle #1
      32.4%
      32.4%

      HINT:
      1. *: Change the control value for Control the VVT Linear to 20% or -20%.
      2. The Control the VVT Linear Active Test considers the value of VVT Aim Angle #1 to be 0 and raises or lowers the duty ratio with respect to VVT Aim Angle #1.
      3. The sum of the control value for the Control the VVT Linear Active Test and the value of VVT Aim Angle #1 is approximately equal to the value of VVT OCV Duty #1.
      4. When the control value for the Control the VVT Linear Active Test is changed a few times, there should not be a large discrepancy between VVT OCV Duty #1 when the system starts advancing or retarding the timing and the rate of change of VVT Change Angle #1.


    5. *7: Control the VVT Exhaust Linear (Bank 1)


      A229972E04


      Tester Display
      Measurement Item/Range
      Normal Condition
      Control the VVT Exhaust Linear (Bank 1)
      -
      ▲A
      ▲B
      Active Test operation*
      10%
      -10%
      VVT Ex Chg Angle #1
      38.5 DegFR
      0.0 DegFR
      VVT Ex OCV Duty #1
      58.9%
      29.0%
      VVT Ex Hold Lrn Val #1
      44.0%
      44.0%

      HINT:
      1. *: Change the control value for Control the VVT Exhaust Linear to 10% or -10%.
      2. The Control the VVT Exhaust Linear Active Test considers the value of VVT Ex Hold Lrn Val #1 to be 0 and raises or lowers the duty ratio with respect to VVT Ex Hold Lrn Val #1.
      3. The sum of the control value for the Control the VVT Exhaust Linear Active Test and the value of VVT Ex Hold Lrn Val #1 is approximately equal to the value of VVT Ex OCV Duty #1.
      4. When the control value for the Control the VVT Exhaust Linear Active Test is changed a few times, there should not be a large discrepancy between VVT Ex OCV Duty #1 when the system starts advancing or retarding the timing and the rate of change of VVT Ex Chg Angle #1.


SYSTEM CHECK

HINT:
Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are stored, and can detect potential malfunctions in the system. The System Check can be performed with the Techstream.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility.

  5. Perform the System Check by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Evaporative System Check
    (Automatic Mode)
    Perform 6 steps in order to operate EVAP system key-off monitor automatically
    35°C (95°F) or less
    1. If no pending DTCs are output after performing this test, the system is functioning normally.
    2. Refer to EVAP system Inspection Procedure (Click here).
    Evaporative System Check
    (Manual Mode)
    Perform 6 steps in order to operate EVAP system key-off monitor manually
    35°C (95°F) or less
    1. Used to detect malfunctioning parts.
    2. Refer to EVAP system Inspection Procedure (Click here).