Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch (power window regulator master switch assembly), and driver door key cylinder or front passenger door key cylinder* switch signals from the front door lock with motor assembly LH or front door lock with motor assembly RH*. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.
  1. *: w/o wireless door lock control function

WIRING DIAGRAM


B297148E01


INSPECTION PROCEDURE

1.CHECK DOOR LOCK OPERATION
  1. Check door lock operation (Click here).

    Result:
    Result
    Proceed to
    All doors cannot be locked through door control switch (power window regulator switch assembly)
    A
    All doors cannot be locked through door key cylinder
    B



B
Go to step 5
A


2.READ VALUE USING TECHSTREAM (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door control switch (power window regulator master switch assembly) or door control switch assembly lock signal/ON or OFF
    ON: Lock side of door control switch (power window regulator master switch assembly) or door control switch assembly pushed
    OFF: Lock side of door control switch (power window regulator master switch assembly) and door control switch assembly not pushed
    -
    Door Lock SW-Unlock
    Door control switch (power window regulator master switch assembly) or door control switch assembly unlock signal/ON or OFF
    ON: Unlock side of door control switch (power window regulator master switch assembly) or door control switch assembly pushed
    OFF: Unlock side of door control switch (power window regulator master switch assembly) and door control switch assembly not pushed
    -

    OK:
    The Techstream indicates ON or OFF according to the switch operation shown in the table above.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
B279066E07
  1. Remove the door control switch (power window regulator master switch assembly) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (L) - 1 (E)
    Lock switch pushed
    Below 1 Ω
    2 (L) - 1 (E)
    off
    10 kΩ or higher
    9 (UL) - 1 (E)
    Unlock switch pushed
    Below 1 Ω
    9 (UL) - 1 (E)
    off
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Door Control Switch (Power Window Regulator Master Switch Assembly))



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the I13 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K11-2 (L) - I13-9 (L1)
    Always
    Below 1 Ω
    K11-9 (UL) - I13-10 (UL1)
    Always
    Below 1 Ω
    K11-1 (E) - Body ground
    Always
    Below 1 Ω
    K11-2 (L) - Body ground
    Always
    10 kΩ or higher
    K11-9 (UL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

5.CHECK DOOR LOCK OPERATION (DOOR KEY CYLINDER)
  1. Proceed to the next step according to the symptom if all the doors cannot be locked/unlocked at once.

    Result:
    Result
    Proceed to
    All doors cannot be locked/unlocked at once by using door key cylinder on driver door.
    A
    All doors cannot be locked/unlocked at once by using door key cylinder on front passenger door.*
    B
    All doors cannot be locked/unlocked at once by using both driver door and front passenger door key cylinder*.
    C

    1. *: w/o Wireless Door Lock Control Function



B
Go to step 9

C
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
A


6.READ VALUE USING TECHSTREAM (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Driver door and front passenger door* key-linked lock/unlock switch lock signal/ON or OFF
    ON: Driver door or front passenger door* key cylinder turned to lock position
    OFF: Driver door and front passenger door* key cylinder not turned to lock position
    -
    D Door Key SW-UL
    Driver door key-linked lock/unlock switch unlock signal/ON or OFF
    ON: Driver door key cylinder turned to unlock position
    OFF: Driver door key cylinder not turned to unlock position
    -

    1. *: w/o Wireless Door Lock Control Function

    OK:
    The Techstream indicates ON or OFF according to the key cylinder operation shown in the table.



NG
Go to step 7
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

7.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH


    B280166E04
  1. Remove the front door lock with motor assembly LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    9 (L) - 7 (E)
    Held to lock side
    Below 1 Ω
    9 (L) - 7 (E)
    Neutral or held to unlock side
    10 kΩ or higher
    10 (UL) - 7 (E)
    Held to unlock side
    Below 1 Ω
    10 (UL) - 7 (E)
    Neutral or held to lock side
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Front Door Lock with Motor Assembly LH)
    *b
    Lock
    *c
    Unlock



NG
REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the I13 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K1-9 (L) - I13-11 (L2)
    Always
    Below 1 Ω
    K1-10 (UL) - I13-24 (UL3)
    Always
    Below 1 Ω
    K1-7 (E) - Body ground
    Always
    Below 1 Ω
    I13-11 (L2) - Body ground
    Always
    10 kΩ or higher
    I13-24 (UL3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

9.READ VALUE USING TECHSTREAM (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Driver door and front passenger door* key-linked lock/unlock switch lock signal/ON or OFF
    ON: Driver door or front passenger door* key cylinder turned to lock position
    OFF: Driver door and front passenger door* key cylinder not turned to lock position
    -
    Door Key SW-Unlock
    Passenger door key-linked lock/unlock switch unlock signal/ON or OFF
    ON: Passenger door key cylinder turned to unlock position
    OFF: Passenger door key cylinder not turned to unlock position
    -

    1. *: w/o Wireless Door Lock Control Function

    OK:
    The Techstream indicates ON or OFF according to the key cylinder operation shown in the table.



NG
Go to step 10
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

10.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH


    B280267E03
  1. Remove the front door lock with motor assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    6 (L) - 8 (E)
    Held to lock side
    Below 1 Ω
    6 (L) - 8 (E)
    Neutral or held to unlock side
    10 kΩ or higher
    5 (UL) - 8 (E)
    Held to unlock side
    Below 1 Ω
    5 (UL) - 8 (E)
    Neutral or held to lock side
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Front Door Lock with Motor Assembly RH)
    *b
    Lock
    *c
    Unlock



NG
REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the I13 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J1-6 (L) - I13-11 (L2)
    Always
    Below 1 Ω
    J1-5 (UL) - I13-12 (UL2)
    Always
    Below 1 Ω
    J1-8 (E) - Body ground
    Always
    Below 1 Ω
    F13-11 (L2) - Body ground
    Always
    10 kΩ or higher
    F13-12 (UL2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)