Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch assembly on the front passenger door and activates the door lock motor on each door according to these signals.

WIRING DIAGRAM


B219490E18


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (DOOR CONTROL SWITCH ASSEMBLY)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door control switch (power window regulator master switch assembly) or door control switch assembly lock signal/ON or OFF
    ON: Lock side of door control switch (power window regulator master switch assembly) or door control switch assembly pushed
    OFF: Lock side of door control switch (power window regulator master switch assembly) and door control switch assembly not pushed
    -
    Door Lock SW-Unlock
    Door control switch (power window regulator master switch assembly) or door control switch assembly unlock signal/ON or OFF
    ON: Unlock side of door control switch (power window regulator master switch assembly) or door control switch assembly pushed
    OFF: Unlock side of door control switch (power window regulator master switch assembly) or door control switch assembly not pushed
    -

    OK:
    The Techstream indicates ON or OFF according to the switch operation shown in the table.



NG
Go to step 2
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

2.INSPECT DOOR CONTROL SWITCH ASSEMBLY


    B279067E01
  1. Remove the door control switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (L) - 3 (E)
    Locked
    Below 1 Ω
    4 (L) - 3 (E)
    off
    10 kΩ or higher
    2 (UL) - 3 (E)
    Unlocked
    Below 1 Ω
    2 (UL) - 3 (E)
    off
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Door Control Switch assembly)
    *b
    Unlock
    *c
    Lock



NG
REPLACE DOOR CONTROL SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the I13 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J12-2 (UL) - I13-10 (UL)
    Always
    Below 1 Ω
    J12-4 (L) - I13-9 (L1)
    Always
    Below 1 Ω
    J12-3 (E) - Body ground
    Always
    Below 1 Ω
    J12-2 (UL) - Body ground
    Always
    10 kΩ or higher
    J12-4 (L) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)