Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0342    Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0343    Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

DTC    P0347    Camshaft Position Sensor "A" Circuit Low Input (Bank 2)

DTC    P0348    Camshaft Position Sensor "A" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The VVT sensor (for intake camshaft) (VV1, VV2 signal) consists of a magnet and MRE (Magneto Resistance Element).
The camshaft timing gear assembly has a sensor plate for the VVT sensor. When the intake camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the intake camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
Then the ECM uses this data to control fuel injection duration, fuel injection timing and Variable Valve Timing (VVT) system.

DTC No.
DTC Detection Condition
Trouble Area
P0340
One of the following conditions is met:
  1. Missing VVT sensor signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or higher (1 trip detection logic).
  2. No VVT sensor signal to ECM at engine speed of 600 rpm or higher (1 trip detection logic).
  3. No VVT sensor signal to ECM while cranking (2 trip detection logic).
  1. Open or short in VVT sensor (for intake camshaft) circuit
  2. VVT sensor (for intake camshaft)
  3. Camshaft timing gear assembly
  4. Valve timing
  5. ECM
P0342
P0347
The output voltage of the VVT sensor is less than 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for intake camshaft) circuit
  2. VVT sensor (for intake camshaft)
  3. ECM
P0343
P0348
The output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for intake camshaft) circuit
  2. VVT sensor (for intake camshaft)
  3. ECM
P0345
No VVT sensor signal at engine speed of 600 rpm or higher (1 trip detection logic).
  1. Open or short in VVT sensor (for intake camshaft) circuit
  2. VVT sensor (for intake camshaft)
  3. Camshaft timing gear assembly
  4. Valve timing
  5. ECM

HINT:
Reference: Inspection using an oscilloscope .


MONITOR DESCRIPTION

If no pulse signal is transmitted by the VVT sensor (for intake camshaft) despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY


Related DTCs
P0340: VVT sensor (bank 1) verify pulse input
P0342: VVT sensor (bank 1) range check (low voltage)
P0343: VVT sensor (bank 1) range check (high voltage)
P0345: VVT sensor (bank 2) verify pulse input
P0347: VVT sensor (bank 2) range check (low voltage)
P0348: VVT sensor (bank 2) range check (high voltage)
Required Sensors/Components (Main)
VVT sensor
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
4 seconds:
P0340 (VVT sensor (bank 1) verify pulse input (case 2))
P0342 and P0347 (VVT sensor (bank 1, 2) range check (low voltage))
P0343 and P0348 (VVT sensor (bank 1, 2) range check (high voltage))
5 seconds:
P0340 (VVT sensor (bank 1) verify pulse input (case 1))
P0345 (VVT sensor (bank 2) verify pulse input)
MIL Operation
2 driving cycles:
P0340 (VVT sensor (bank 1) verify pulse input (case 2))
Immediate:
Others
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None

P0340: VVT Sensor (Bank 1) Verify Pulse Input (Case 1) 
All of the following conditions are met
-
Engine speed
600 rpm or higher
Starter
Off
VVT system mis-alignment
Not detected
VVT sensor range check fail (P0342, P0343)
Not detected
VVT sensor voltage
0.3 to 4.7 V

P0340: VVT Sensor (Bank 1) Verify Pulse Input (Case 2) 
Both of the following conditions are met
-
Starter
On
Minimal battery voltage while starter on
Less than 11 V

P0342 and P0343: VVT Sensor (Bank 1) Range Check 
All of the following conditions are met
-
Starter
Off
Engine switch
On (IG)
Time after engine switch off to on (IG)
2 seconds or more
VVT sensor pulse input fail (P0340)
Not detected
Battery voltage
8 V or higher

P0345: VVT Sensor (Bank 2) Verify Pulse Input 
All of the following conditions are met
-
Engine speed
600 rpm or higher
Starter
Off
VVT sensor range check fail (P0342, P0343, P0347, P0348)
Not detected
VVT sensor voltage
0.3 to 4.7 V
Battery voltage
8 V or higher
Engine switch
On (IG)
Time after engine switch off to on (IG)
More than 0.5 seconds

P0347 and P0348: VVT Sensor (Bank 2) Range Check 
All of the following conditions are met
-
Starter
Off
Engine switch
On (IG)
Time after engine switch off to on (IG)
2 seconds or more
VVT sensor verify pulse input fail (P0340, P0345)
Not detected
Battery voltage
8 V or higher

TYPICAL MALFUNCTION THRESHOLDS


P0340: VVT Sensor (Bank 1) Verify Pulse Input (Case 1) 
Either of the following conditions is met
1 or 2
1. Camshaft position and crankshaft position alignment
Mis-alignment
2. VVT sensor signal
No signal

P0340: VVT Sensor (Bank 1) Verify Pulse Input (Case 2) 
VVT sensor signal
No signal

P0342 and P0347: VVT Sensor (Bank1, 2) Range Check (Low Voltage) 
VVT sensor voltage
Less than 0.3 V

P0343 and P0348: VVT Sensor (Bank1, 2) Range Check (High voltage) 
VVT sensor voltage
Higher than 4.7 V

P0345: VVT Sensor (Bank 2) Verify Pulse Input 
VVT sensor signal
No signal

COMPONENT OPERATING RANGE


VVT sensor voltage
0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine / Trouble Codes [B].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR INTAKE CAMSHAFT))


    A194108E72
  1. Disconnect the VVT sensor (for intake camshaft) connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E54-3 (VC) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V
    E60-3 (VC) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2
    *a
    Front view of wire harness connector
    (to VVT Sensor (for Intake Camshaft))



NG
Go to step 8
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
  1. Disconnect the VVT sensor (for intake camshaft) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E54-1 (VVR+) - E26-81 (VV1+)
    Always
    Below 1 Ω
    E54-2 (VVR-) - E26-110 (VV1-)
    Always
    Below 1 Ω
    E60-1 (VVL+) - E26-78 (VV2+)
    Always
    Below 1 Ω
    E60-2 (VVL-) - E26-110 (VV1-)
    Always
    Below 1 Ω
    E54-1 (VVR+) or E26-81 (VV1+) - Body ground
    Always
    10 kΩ or higher
    E54-2 (VVR-) or E26-110 (VV1-) - Body ground
    Always
    10 kΩ or higher
    E60-1 (VVL+) or E26-78 (VV2+) - Body ground
    Always
    10 kΩ or higher
    E60-2 (VVL-) or E26-110 (VV1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT))


    BR03795E17
  1. Check the VVT sensor (for intake camshaft) installation.

    OK:
    VVT sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR (FOR INTAKE CAMSHAFT) (Click here)
OK


4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)
  1. Inspect the teeth of the sensor plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)


    A135015E03
  1. Remove the cylinder head cover sub-assemblies RH and LH (Click here).

  1. Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.

    HINT:
    If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

    OK:
    The timing marks on the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark



NG
ADJUST VALVE TIMING (Click here)
OK


6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)
  1. Replace the VVT sensor (for intake camshaft) (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    DTC P0340, P0342, P0343, P0345, P0347 or P0348 is output
    A
    DTC is not output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
END
A

REPLACE ECM (Click here)  

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
  1. Disconnect the VVT sensor (for intake camshaft) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E54-3 (VC) - E26-111 (VCV1)
    Always
    Below 1 Ω
    E60-3 (VC) - E26-111 (VCV1)
    Always
    Below 1 Ω
    E54-3 (VC) or E26-111 (VCV1) - Body ground
    Always
    10 kΩ or higher
    E60-3 (VC) or E26-111 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)