Home › Engine / Hybrid System ยท 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

DTC    P0430    Catalyst System Efficiency Below Threshold (Bank 2)

for Preparation Click here


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stores the DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No.
DTC Detection Condition
Trouble Area
P0420
The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
  1. Gas leak from exhaust system
  2. Air fuel ratio sensor (bank 1 sensor 1)
  3. Heated oxygen sensor (bank 1 sensor 2)
  4. Exhaust manifold sub-assembly RH (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)
P0430
The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
  1. Gas leak from exhaust system
  2. Air fuel ratio sensor (bank 2 sensor 1)
  3. Heated oxygen sensor (bank 2 sensor 2)
  4. Exhaust manifold sub-assembly LH (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)

CATALYST LOCATION


A255688E01


Text in Illustration 
*1
Air Fuel Ratio Sensor (Bank 1 Sensor 1)
*2
Air Fuel Ratio Sensor (Bank 2 Sensor 1)
*3
Heated Oxygen Sensor (Bank 1 Sensor 2)
*4
Heated Oxygen Sensor (Bank 2 Sensor 2)
*5
TWC: Front Catalyst
*6
TWC: Rear Catalyst
*7
Center Exhaust Pipe Assembly
*8
Tail Exhaust Pipe Assembly RH
*9
Tail Exhaust Pipe Assembly LH
*10
Exhaust Manifold Sub-assembly RH
*11
Exhaust Manifold Sub-assembly LH
*12
Front Exhaust Pipe Assembly

NOTICE:
  1. When outputting DTC P0420 replace the exhaust manifold sub-assembly RH (*10) and the front exhaust pipe assembly (*12) together when catalyst replacement is necessary (Excluding air fuel ratio sensor *1 and heated oxygen sensor *3).
  2. When outputting DTC P0430 replace the exhaust manifold sub-assembly LH (*11) and the front exhaust pipe assembly (*12) together when catalyst replacement is necessary (Excluding air fuel ratio sensor *2 and heated oxygen sensor *4).


MONITOR STRATEGY


Related DTCs
P0420: Catalyst deterioration (bank 1)
P0430: Catalyst deterioration (bank 2)
Required Sensors/Components (Main)
Air fuel ratio sensor
Heated oxygen sensor
Required Sensors/Components (Related)
Intake air temperature sensor
Mass air flow meter sub-assembly
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
Approximately 30 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever the following DTCs are not stored
P0010, P0020 (Camshaft timing oil control valve bank 1, 2)
P0011, P0021 (VVT system bank 1, 2 - advance)
P0012, P0022 (VVT system bank 1, 2 - retard)
P0013, P0023 (Exhaust camshaft timing oil control valve bank 1, 2)
P0014, P0024 (Exhaust VVT system bank 1, 2 - advance)
P0015, P0025 (Exhaust VVT system bank 1, 2 - retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058, P102D, P105D (Heated oxygen sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0136, P0137, P0138, P0139, P0156, P0157, P0158, P0159, P0607 (Heated oxygen sensor)
P014C, P014D, P14E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0500 (Vehicle speed sensor)
P219A, P219B (Air-fuel ratio imbalance)
Battery voltage
11 V or higher
Intake air temperature
-10°C (14°F) or higher
Engine coolant temperature
75°C (167°F) or higher
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or higher
Idling
Off
Engine speed
Less than 3200 rpm
Air fuel ratio sensor status
Activated
Fuel system status
Closed loop
Engine load
10% or higher, and less than 70%
All of the following conditions are met
1, 2 and 3
1. Mass air flow
5 gm/sec or more, and less than 75 gm/sec
2. Front catalyst temperature (estimated)
520°C (968°F) or higher, and less than 800°C (1472°F)
3. Rear catalyst temperature (estimated)
300°C (572°F) or higher, and less than 800°C (1472°F)
Shift position
3rd or higher

TYPICAL MALFUNCTION THRESHOLDS


Oxygen Storage Capacity (OSC) of catalyst
Less than 0.051 g

MONITOR RESULT

Refer to detailed information in Checking Monitor Status (Click here).

P0420: Catalyst Efficiency / O2 STORAGE B1 
Monitor ID
Test ID
Scaling
Unit
Description
$21
$A9
Multiply by 0.0003
No dimension
Oxygen storage capacity of catalyst bank 1

P0430: Catalyst Efficiency / O2 STORAGE B2 
Monitor ID
Test ID
Scaling
Unit
Description
$22
$A9
Multiply by 0.0003
No dimension
Oxygen storage capacity of catalyst bank 2

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A231470E75

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG)
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the engine off and wait for at least 30 seconds.
  6. Turn the engine switch on (IG) and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine / Monitor / Current Monitor.
  8. Check that Catalyst Efficiency / Current is Incomplete.
  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  10. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates [C].

  11. Enter the following menus: Powertrain / Engine / Trouble Codes.
  12. Check if any DTCs (pending DTCs) are stored.

    HINT:
    If the monitor item does not change to Complete, and no pending DTCs are stored, perform the following procedure.

  13. Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates [E].

  14. Enter the following menus: Powertrain / Engine / Trouble Codes.
  15. Check if any DTCs (pending DTCs) are stored.

    HINT:
    If the monitor item does not change to Complete, and no pending DTCs are stored, extend the driving time.

  16. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


CONDITIONING FOR SENSOR TESTING

HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A118003E93

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.
  3. (c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.
  4. (d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the Techstream.

HINT:
  1. If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.
  2. If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume Active Test using the Techstream.
  3. If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).

A199479E18


INSPECTION PROCEDURE

HINT:
  1. If a malfunction cannot be found when troubleshooting DTC P0420 or P0430, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 and P0174 (System Too Lean), and P0172 and P0175 (System Too Rich).
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.
  6. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 and/or P0430 are output
    A
    DTC P0420 and/or P0430 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0420 and/or P0430 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Turn the Techstream on.

  1. Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Gas AF Control / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

  1. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. Change the fuel injection volume within the range of - 12% to +12%. The injection volume can be changed in fine gradations.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    4. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Techstream Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1
    AFS Voltage B2S1
    (Air fuel ratio)
    +12%
    Rich
    Below 3.1 V
    -12%
    Lean
    Higher than 3.4 V
    O2S B1S2
    O2S B2S2
    (Heated oxygen)
    +12%
    Rich
    Higher than 0.55 V
    -12%
    Lean
    Below 0.4 V


    Result 
    Status
    AFS Voltage B1S1 or AFS Voltage B2S1
    Status
    O2S B1S2 or O2S B2S2
    Actual air fuel ratio, air fuel ratio sensor and
    heated oxygen sensor condition
    Misfire
    Main Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-way catalytic converter
    2. Gas leak from exhaust system
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    Lean/Rich
    Lean
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leak from exhaust system
    C
    Lean/Rich
    Rich
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leak from exhaust system
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leak from exhaust system
    D
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leak from exhaust system
    1. Lean: During Control the Injection Volume, the air fuel ratio sensor output voltage (AFS Voltage B1S1 or AFS Voltage B2S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2 or O2S B2S2) is consistently below 0.4 V.
    2. Rich: During Control the Injection Volume, the AFS Voltage B1S1 or AFS Voltage B2S1 is consistently below 3.1 V, and the O2S B1S2 or O2S B2S2 is consistently higher than 0.55 V.
    3. Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



B
Go to step 7

C
Go to step 5

D
Go to step 6
A


3.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 8
OK


4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NOTICE:
  1. When outputting DTC P0420 replace the exhaust manifold sub-assembly RH (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.
  2. When outputting DTC P0430 replace the exhaust manifold sub-assembly LH (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 is output
    A, C
    DTC P0430 is output
    B, C
    DTC P0420 and P0430 are output
    A, B, C



A
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST) (Click here)

B
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST) (Click here)
C

REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) (Click here)  

5.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



OK
Go to step 9

NG
Go to step 8

6.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



OK
Go to step 10

NG
Go to step 8

7.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NEXT
Go to step 11

8.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
  1. Repair or replace exhaust gas leak point.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NEXT
Go to step 11

9.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).



NEXT
Go to step 11

10.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
  1. Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .


NEXT


11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 and/or P0430 is output
    A
    DTC is not output
    B



B
END
A


12.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NOTICE:
  1. When outputting DTC P0420 replace the exhaust manifold sub-assembly RH (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.
  2. When outputting DTC P0430 replace the exhaust manifold sub-assembly LH (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 is output
    A, C
    DTC P0430 is output
    B, C
    DTC P0420 and P0430 are output
    A, B, C



A
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST) (Click here)

B
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST) (Click here)
C

REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) (Click here)