Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Separate Type Yaw Rate Sensor)

DTC    B1805/52    Short in Front Passenger Side Squib Circuit

DTC    B1806/52    Open in Front Passenger Side Squib Circuit

DTC    B1807/52    Short to GND in Front Passenger Side Squib Circuit

DTC    B1808/52    Short to B+ in Front Passenger Side Squib Circuit

for Preparation Click here


DESCRIPTION

The front passenger side squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.
The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1805/52
  1. The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit during primary check.
  2. Front passenger side squib malfunction
  3. Airbag sensor assembly malfunction
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Instrument panel passenger airbag assembly (Front passenger side squib)
  4. Airbag sensor assembly
B1806/52
  1. The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit.
  2. Front passenger side squib malfunction
  3. Airbag sensor assembly malfunction
B1807/52
  1. The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib circuit.
  2. Front passenger side squib malfunction
  3. Airbag sensor assembly malfunction
B1808/52
  1. The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit.
  2. Front passenger side squib malfunction
  3. Airbag sensor assembly malfunction

WIRING DIAGRAM


C239227E20


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the Techstream (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).

1.CHECK CONNECTORS


    C241746E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag sensor assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the instrument panel passenger airbag assembly and airbag sensor assembly. Also disconnect the instrument panel wire from the No. 2 instrument panel wire.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the No. 2 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.

  1. Check that the short springs for the instrument panel wire and No. 2 instrument panel wire with the activation prevention mechanism are not deformed or damaged.

    OK:
    The short springs are not deformed or damaged.

    Text in Illustration 
    *1
    Instrument Panel Passenger Airbag Assembly
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Instrument Panel Wire
    *4
    Instrument Panel Wire



NG
REPLACE WIRE HARNESS
OK


2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)


    C241747E06
  1. Connect the instrument panel wire to the No. 2 instrument panel wire and airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector E (orange connector).

    CAUTION:
    Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting it.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.

    HINT:
    Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect SST from connector E.
    Text in Illustration 
    *1
    Instrument Panel Passenger Airbag Assembly
    *2
    Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Instrument Panel Passenger Airbag Assembly)
    *b
    Color: Orange



NG
Go to step 3
OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (Click here)  

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT


    C238254E08
  1. Disconnect the instrument panel wire from the airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      b1-2 (P+) - Body ground
      Ignition switch ON
      Below 1 V
      b1-1 (P-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      b1-2 (P+) - b1-1 (P-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      b1-2 (P+) - Body ground
      Always
      1 MΩ or higher
      b1-1 (P-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      b1-2 (P+) - b1-1 (P-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.
      Text in Illustration 
      *1
      Instrument Panel Passenger Airbag Assembly
      *2
      Airbag Sensor Assembly
      *a
      Front view of wire harness connector
      (to Instrument Panel Passenger Airbag Assembly)
      *b
      Color: Orange



NG
Go to step 5
OK


4.CHECK DTC


    C238235E01
  1. Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.

    HINT:
    Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Instrument Panel Passenger Airbag Assembly
    *2
    Airbag Sensor Assembly



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE


    C241748E07
  1. Disconnect the No. 2 instrument panel wire from the instrument panel wire.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      lb2-1 (P+) - Body ground
      Ignition switch ON
      Below 1 V
      lb2-2 (P-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      lb2-1 (P+) - lb2-2 (P-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      lb2-1 (P+) - Body ground
      Always
      1 MΩ or higher
      lb2-2 (P-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      lb2-1 (P+) - lb2-2 (P-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.
      Text in Illustration 
      *1
      Instrument Panel Passenger Airbag Assembly
      *2
      Airbag Sensor Assembly
      *3
      No. 2 Instrument Panel Wire
      *4
      Instrument Panel Wire
      *a
      Front view of wire harness connector
      (to No. 2 Instrument Panel Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK NO. 2 INSTRUMENT PANEL WIRE


    C238256E08
  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      b1-2 (P+) - Body ground
      Ignition switch ON
      Below 1 V
      b1-1 (P-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      b1-2 (P+) - b1-1 (P-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      b1-2 (P+) - Body ground
      Always
      1 MΩ or higher
      b1-1 (P-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector D (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      b1-2 (P+) - b1-1 (P-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector D to the original condition.
      Text in Illustration 
      *1
      Instrument Panel Passenger Airbag Assembly
      *2
      Airbag Sensor Assembly
      *3
      No. 2 Instrument Panel Wire
      *4
      Instrument Panel Wire
      *a
      Front view of wire harness connector
      (to Instrument Panel Passenger Airbag Assembly)
      *b
      Color: Orange



NG
REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK

USE SIMULATION METHOD TO CHECK (Click here)